The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during instrument panel safety pad removal/installation are shown below.
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
1. PRECAUTION
Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>PRECAUTION
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2. CHANGE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM SETTINGS (for Power Tilt and Power Telescopic Steering Column)
3.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
45130
4.REMOVE HORN BUTTON ASSEMBLY
5.REMOVE STEERING WHEEL ASSEMBLY
45024
6.REMOVE LOWER STEERING COLUMN COVER SUB-ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)
45024
7.REMOVE LOWER STEERING COLUMN COVER SUB-ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)
45286B
8.REMOVE UPPER STEERING COLUMN COVER (for Manual Tilt and Manual Telescopic Steering Column)
45286B
9.REMOVE UPPER STEERING COLUMN COVER (for Power Tilt and Power Telescopic Steering Column)
84650
10.REMOVE WINDSHIELD WIPER SWITCH ASSEMBLY
84329
11.REMOVE TURN SIGNAL SWITCH
58810J
12.REMOVE CONSOLE BOX ASSEMBLY
67914
13.REMOVE FRONT DOOR SCUFF PLATE LH
62112A
14.REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH
62312B
15.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Disconnect the front door opening trim weatherstrip LH.
62212
16.REMOVE FRONT PILLAR GARNISH LH
55318C
17.REMOVE INSTRUMENT SIDE PANEL LH
|
Protective Tape |
Apply protective tape to the area shown in the illustration.
|
Remove in this Direction |
Using a moulding remover, disengage the 2 claws and 4 clips as shown in the illustration.
To prevent damage to the instrument side panel LH, do not insert the moulding remover in a position other than shown in the illustration.
|
Remove in this Direction |
Disengage the 3 guides to remove the instrument side panel LH as shown in the illustration.
55606
18.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)
Remove the 2 screws <C>.
|
Remove in this Direction |
Disengage the 3 claws as shown in the illustration.
|
Remove in this Direction |
Disengage the guide as shown in the illustration.
Disconnect the connector.
Disengage the 2 claws to disconnect the DLC3 connector.
Disengage the 2 clamps to remove the No. 1 instrument panel under cover sub-assembly.
55606
19.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)
Remove the 3 screws <C>.
|
Remove in this Direction |
Disengage the 2 claws as shown in the illustration.
Disconnect the connector.
Disengage the 2 claws to disconnect the DLC3 connector.
Disengage the clamp to remove the No. 1 instrument panel under cover sub-assembly.
55436B
20.REMOVE NO. 2 METER HOOD CLUSTER
|
Place Hand Here |
|
Remove in this Direction |
Disengage the 3 clips to remove the No. 2 meter hood cluster as shown in the illustration.
53601
21.DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.
55302D
22.REMOVE NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY
|
Remove in this Direction |
Disengage the 6 clips as shown in the illustration.
Disengage the clamp.
Disconnect each connector to remove the No. 1 instrument panel sub-assembly.
73900
23.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY
55410C
24.REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
Remove the 2 clips.
|
Place Hand Here |
|
Remove in this Direction |
Disengage the 2 clips as shown in the illustration.
|
Place Hand Here |
|
Remove in this Direction |
Disengage the 2 clips as shown in the illustration.
|
Remove in this Direction |
Disengage the 2 guides as shown in the illustration.
Disconnect the connector to remove the instrument cluster finish panel assembly.
83100
25.REMOVE COMBINATION METER ASSEMBLY
55480D
26.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
|
Place Hand Here |
|
Remove in this Direction |
Disengage the 5 clips as shown in the illustration.
Disconnect the connector to remove the lower instrument panel finish panel assembly.
55670
27.REMOVE NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY
Disengage the 8 clips in the order shown in the illustration.
|
Place Hand Here |
|
Remove in this Direction |
Disengage the 3 clips in the order shown in the illustration.
|
Place Hand Here |
|
Remove in this Direction |
Disconnect the connector to remove the No. 3 instrument panel register assembly.
55900
28.REMOVE AIR CONDITIONING CONTROL ASSEMBLY (w/o Radio Receiver)
55423B
29.REMOVE INSTRUMENT CLUSTER FINISH PANEL COVER (w/o Radio Receiver)
Disengage the 4 clips to remove the instrument cluster finish panel cover as shown in the illustration.
|
Place Hand Here |
|
Remove in this Direction |
55420A
30.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/o Radio Receiver)
Disengage the 4 clips in the order shown in the illustration.
|
Place Hand Here |
|
Remove in this Direction |
Disengage the 5 clips as shown in the illustration.
|
Place Hand Here |
|
Remove in this Direction |
Disconnect the connector to remove the center instrument cluster finish panel assembly.
31.REMOVE RADIO TUNER OPENING COVER WITH BRACKET (w/o Radio Receiver)
Remove the 4 bolts <B>.
Disconnect the connector to remove the radio tuner opening cover with bracket.
32.REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (w/ Radio Receiver)
67913
33.REMOVE FRONT DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
62111A
34.REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH
Use the same procedure as for the LH side.
62311B
35.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure as for the LH side.
62211
36.REMOVE FRONT PILLAR GARNISH RH
Use the same procedure as for the LH side.
55317A
37.REMOVE INSTRUMENT SIDE PANEL RH
|
Protective Tape |
Apply protective tape to the area shown in the illustration.
|
Remove in this Direction |
Using a moulding remover, disengage the 2 claws and 4 clips as shown in the illustration.
To prevent damage to the instrument side panel RH, do not insert the moulding remover in a position other than shown in the illustration.
|
Remove in this Direction |
Disengage the 3 guides to remove the instrument side panel RH as shown in the illustration.
55607
38.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
|
Remove in this Direction |
Disengage the 4 claws as shown in the illustration.
|
Remove in this Direction |
Disengage the 2 guides as shown in the illustration.
Disengage the clamp.
Disconnect the connector to remove the No. 2 instrument panel under cover sub-assembly.
73990
39.REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Passenger Side Knee Airbag)
55303B
40.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/o Passenger Side Knee Airbag)
| *a | Screws <C> |
| *b | Bolts <D> |
Remove the 3 screws <C>.
Remove the 2 bolts <D>.
|
Remove in this Direction |
Disengage the 4 claws as shown in the illustration.
Disconnect the connector to remove the lower instrument panel sub-assembly.
55303B
41.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/ Passenger Side Knee Airbag)
Remove the 5 screws <C>.
|
Remove in this Direction |
Disengage the 4 claws as shown in the illustration.
Disconnect the connector to remove the lower instrument panel sub-assembly.
55472C
42.REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL
|
Place Hand Here |
|
Remove in this Direction |
Disengage the 2 clips as shown in the illustration.
|
Remove in this Direction |
Disengage the 2 guides to remove the No. 1 instrument panel speaker panel as shown in the illustration.
86160P
43.REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)
55473B
44.REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL
|
Place Hand Here |
|
Remove in this Direction |
Disengage the 2 clips as shown in the illustration.
|
Remove in this Direction |
Disengage the 2 guides to remove the No. 2 instrument panel speaker panel as shown in the illustration.
86160P
45.REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)
Use the same procedure as for the LH side.
55011A
46.REMOVE NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY
|
Place Hand Here |
|
Remove in this Direction |
Disengage the 4 clips to remove the No. 1 instrument panel garnish sub-assembly as shown in the illustration.
55650
47.REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY
|
Place Hand Here |
|
Remove in this Direction |
Disengage the 2 clips and 2 claws to remove the No. 1 instrument panel register assembly as shown in the illustration.
82149A
48.DISCONNECT NO. 5 INSTRUMENT PANEL WIRE (w/o Occupant Classification System)
82149A
49.DISCONNECT NO. 5 INSTRUMENT PANEL WIRE (w/ Occupant Classification System)
50.REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY
|
Remove in this Direction |
Disengage the 2 claws to disconnect the cooler (room temp. sensor) thermistor as shown in the illustration.
Disconnect each connector.
| *A | w/ Digital Audio Broadcasting Antenna or Television Antenna | *B | w/ Ion Generator |
| *C | w/ Headup Display | - | - |
Disengage each clamp.
Remove the 2 clips.
| *a | Bolt <A> | *b | Bolt <B> |
| *c | Clip | *d | Nut <F> |
Remove the 4 bolts <B>, 2 bolts <A> and nut <F>.
Disengage the 4 guides and remove the instrument panel safety pad sub-assembly as shown in the illustration.
|
Remove in this Direction | - | - |
Do not damage the instrument panel safety pad sub-assembly.
Do not allow the wire harnesses to interfere with the surrounding parts.