The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during instrument panel passenger airbag assembly removal/installation are shown below.
1. PRECAUTION
Be sure to read Precaution thoroughly before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
55650
2.REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY
82149A
3.DISCONNECT NO. 5 INSTRUMENT PANEL WIRE (w/o Occupant Classification System)
Check that the power switch is off.
Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
| *a | Slider |
|
Release in this Direction |
Slide the slider to release the lock, and then disconnect the connector.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
82149A
4.DISCONNECT NO. 5 INSTRUMENT PANEL WIRE (w/ Occupant Classification System)
Check that the power switch is off.
Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
| *a | Slider |
|
Release in this Direction |
Slide the slider to release the lock, and then disconnect the connector.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
5.REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY
73960A
6.REMOVE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (w/o Occupant Classification System)
|
Deployment Side |
When storing the instrument panel passenger airbag assembly, keep the airbag deployment side facing upward.
Remove the 2 screws and disengage the clamp.
| *a | Passenger Airbag Door Retainer |
|
Move the screwdriver in this Direction |
Using a screwdriver, pry back the passenger airbag door retainer to disengage the 3 hooks as shown in the illustration.
Do not damage the deployment surface of the instrument panel passenger airbag assembly.
Disengage the 3 hooks to remove the instrument panel passenger airbag assembly from the instrument panel safety pad sub-assembly.
73960A
7.REMOVE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (w/ Occupant Classification System)
|
Deployment Side |
When storing the instrument panel passenger airbag assembly, keep the airbag deployment side facing upward.
Remove the 2 screws and disengage the clamp.
| *a | Passenger Airbag Door Retainer |
|
Move the screwdriver in this Direction |
Using a screwdriver, pry back the passenger airbag door retainer to disengage the 3 hooks as shown in the illustration.
Do not damage the deployment surface of the instrument panel passenger airbag assembly.
Disengage the 3 hooks to remove the instrument panel passenger airbag assembly from the instrument panel safety pad sub-assembly.
82149A
8.REMOVE NO. 5 INSTRUMENT PANEL WIRE (w/o Occupant Classification System)
| *a | Protective Tape |
| *b | Airbag Connector |
| *c | Airbag Connector Locking Button |
|
Release in this Direction |
Using a screwdriver with its tip wrapped with protective tape, release the airbag connector locking button.
Disconnect the airbag connector to remove the No. 5 instrument panel wire from the instrument panel passenger airbag assembly.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
82149A
9.REMOVE NO. 5 INSTRUMENT PANEL WIRE (w/ Occupant Classification System)
| *a | Protective Tape |
| *b | Airbag Connector |
| *c | Airbag Connector Locking Button |
|
Release in this Direction |
Using a screwdriver with its tip wrapped with protective tape, release the 2 airbag connector locking buttons.
Disconnect the 2 airbag connectors to remove the No. 5 instrument panel wire from the instrument panel passenger airbag assembly.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.