Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SIDE AIRBAG SENSOR (for Front Door)
RM33C0E _58 Vehicle Interior _065460 SUPPLEMENTAL RESTRAINT SYSTEMS _0331869 SIDE AIRBAG SENSOR(for Front Door) A

SUPPLEMENTAL RESTRAINT SYSTEMS  SIDE AIRBAG SENSOR(for Front Door)  INSTALLATION  


PROCEDURE

Hide 89835 1.INSTALL DOOR SIDE AIRBAG SENSOR

a.

Check that the power switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Before connecting the connector, check that the position of the white housing lock is as shown in the illustration.

B296255C05
4.76,1.833 5.031,2.104 0.271,0.271 10 false *b 1.396,1.833 1.677,2.115 0.281,0.281 10 false *b 4.76,0.573 5.031,0.875 0.271,0.302 10 false *a 1.396,0.573 1.677,0.865 0.281,0.292 10 false *a
*a Incorrect *b Correct



d.
B474823C01
1.031,0.906 1.573,0.906 true 0.833,0.813 1.042,1.01 0.208,0.198 10 true *a
*a Stopper


Insert the door side airbag sensor stopper into the door hole, engage the claw and install the door side airbag sensor to the front door panel with the nut.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:
·

If the door side airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.

·

When installing the door side airbag sensor, make sure that the SRS wiring does not interfere with or is not pinched between other parts.

·

Make sure that the door side airbag sensor stopper is securely inserted into the door hole.

·

Keep the stud bolt and waterproof rubber seal free of foreign matter.




e.

Connect the connector to the door side airbag sensor.

B312074C10
2.208,0.802 2.385,0.531 true 2.385,0.531 2.583,0.531 false 2.417,1.01 3,0.792 true 3.052,0.677 3.26,0.885 0.208,0.208 10 false *a 5.938,3.365 6.25,3.521 0.313,0.156 10 false *b 2.615,0.469 2.948,0.698 0.333,0.229 10 false A
*a White Housing Lock *b Connection is completed


NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.


HINT:
·

Be sure to connect the connector until it is locked (when locking, make sure that a click sound can be heard).

·

When the connector is locked, the white housing lock will slide. Do not hold the white housing lock or the part (A) as it may result in an insecure connection.




f.

Check that there is no looseness in the installed parts of the door side airbag sensor.


Hide 67832 2.INSTALL FRONT DOOR SERVICE HOLE COVER

Hide 67602 3.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Hide 81230 4.INSTALL COURTESY LIGHT ASSEMBLY

Hide 74220 5.INSTALL FRONT ARMREST ASSEMBLY

Hide 6.INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

Hide 7.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)

Hide 74038A 8.INSTALL FRONT DOOR ARMREST COVER SUB-ASSEMBLY

Hide 67492A 9.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH

Hide 10.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>AUXILIARY BATTERY>INSTALLATION

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 64718C 11.INSTALL LUGGAGE TRIM SERVICE HOLE COVER