Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR
RM33C0E _59 Vehicle Exterior _065469 DOOR / HATCH _0333680 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 75754A 5.INSTALL FRONT DOOR UPPER WINDOW FRAME MOULDING

Hide 67852D 6.INSTALL FRONT DOOR REAR OUTSIDE SEAL

a.
B471661

Engage the guide to install the front door rear outside seal.


Hide 75756C 7.INSTALL FRONT DOOR REAR WINDOW FRAME MOULDING

Hide 75792 8.INSTALL DOOR WINDOW FRAME MOULDING CLIP

a.
B469835C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 claws to install the door window frame moulding clip.


Hide 67496A 9.INSTALL FRONT DOOR FRONT LOWER FRAME UPPER COVER

Hide 75720 10.INSTALL FRONT DOOR BELT MOULDING ASSEMBLY

Hide 67864B 11.INSTALL FRONT DOOR NO. 2 WEATHERSTRIP

a.
B471468

Engage the 8 clips to install the front door No. 2 weatherstrip.


Hide 67001A 12.INSTALL FRONT DOOR PANEL CUSHION

a.
B481250

Engage the 2 claws to install new front door panel cushion.


Hide 67402F 13.INSTALL FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY

a.
B471447C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guide as shown in the illustration.


b.

Install the front door front lower frame sub-assembly with the 2 bolts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 67664C 14.INSTALL DOOR FRAME GARNISH

a.
B471466

Engage the 3 claws to install the door frame garnish.


Hide 67862 15.INSTALL FRONT DOOR WEATHERSTRIP

a.
B471469

Engage the 25 clips and install the front door weatherstrip.


Hide 68620 16.INSTALL FRONT DOOR CHECK ASSEMBLY

a.

Clean the bolt hole in the vehicle body.


b.

Clean the threads of the bolt.


c.

Apply adhesive to the threads of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.
B471464C02
0,0 0,0 false
V100135

Nut
V100136

Bolt


Install the front door check assembly with the 2 nuts and bolt.

Torque:
Bolt : 29 N*m (296 kgf*cm, 21 ft.*lbf)
Nut : 8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 69312 17.INSTALL FRONT DOOR LOCK OPEN ROD

a.
B471463C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Install the front door lock open rod as indicated by the arrows, in the order shown in the illustration.


Hide 69202A 18.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.

Apply MP grease to the sliding parts on the front door outside handle frame sub-assembly.


b.
B471470C01
0.073,0.073 0.458,0.396 0.385,0.323 12 true *A 0.073,2.656 0.427,2.948 0.354,0.292 12 true *B
*A Outside
*B Inside


Engage the claw as shown in the illustration.


c.

Using a T30 "TORX" socket wrench, install the front door outside handle frame sub-assembly with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69040A 19.INSTALL FRONT DOOR LOCK WITH MOTOR ASSEMBLY

Hide 69242E 20.INSTALL FRONT DOOR REAR OUTSIDE HANDLE PAD

a.
B471460

Engage the 3 guides.


b.

Engage the claw to install the front door rear outside handle pad.


Hide 69241H 21.INSTALL FRONT DOOR FRONT OUTSIDE HANDLE PAD

a.
B471459

Engage the 3 claws to install the front door front outside handle pad.


Hide 69217F 22.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)

a.
B471458

Engage the 2 guides and claw.


b.

Using a T30 "TORX" socket wrench, install the front door outside handle cover with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


c.
B471457

Install the hole plug.


Hide 23.INSTALL FRONT DOOR LOCK CYLINDER ASSEMBLY (for Driver Side)

a.
B471456

Using a T30 "TORX" socket wrench, install the front door lock cylinder assembly with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


b.
B471455

Install the hole plug.


Hide 69220 24.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY

a.
B471454C01
0,0 0,0 false
V113147

Install in this Direction


Insert the front end of the front door outside handle assembly into the front door outside handle frame sub-assembly.


b.

Insert the rear end of the front door outside handle assembly into the front door outside handle frame sub-assembly, then slide the front door outside handle assembly toward the front of the vehicle to install it.


c.
B471452C01
0,0 0,0 false
V113147

Engage in this Direction


Move the lever as shown in the illustration and engage the 2 claws to secure the front door outside handle assembly.


d.
B471450

Engage the 3 clamps.


e.
B471449

Connect the connector.


f.

Engage the 2 claws.


Hide 67404F 25.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

a.
B471445C02
0,0 0,0 false
V113147

Install in this Direction


Engage the guide as shown in the illustration.


b.

Install the front door rear lower frame sub-assembly with the 2 bolts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 68151C 26.INSTALL FRONT DOOR GLASS RUN

a.
B471443

Install the front door glass run.


Hide 67856B 27.INSTALL FRONT DOOR PANEL PROTECTOR

a.
B471722

Install the front door panel protector.


Hide 28.INSTALL FRONT DOOR WINDOW REGULATOR ASSEMBLY

a.

Apply MP grease to the sliding parts of the front door window regulator assembly.


b.

Temporarily install the temporary bolt to the front door window regulator assembly.


c.
B471471C01
1.219,0.479 1.917,0.917 true 0.969,0.365 1.219,0.573 0.25,0.208 10 true *a 1.844,1.677 2,1.875 0.156,0.198 10 true 1 2.031,0.198 2.188,0.396 0.156,0.198 10 true 2 2.521,1.5 2.677,1.698 0.156,0.198 10 true 3 1.677,0.365 1.833,0.563 0.156,0.198 10 true 4 0.479,0.719 0.635,0.917 0.156,0.198 10 true 5 1.198,0.625 1.354,0.823 0.156,0.198 10 true 6
*a Temporary Bolt


Temporarily install the front door window regulator assembly with the 5 bolts.


d.

Tighten the temporary bolt and 5 bolts to install the front door window regulator assembly.

HINT:

Tighten the bolts in the order shown in the illustration.


Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Connect the connector.


f.
B471441

Engage the 2 claws to install the front door No. 2 service hole cover.


Hide 68102 29.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

a.

for Driver Side:

i.

Connect the multiplex network master switch assembly.



b.

for Front Passenger Side:

i.

Connect the power window regulator switch assembly.



c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).


e.

Move the front door window regulator assembly so that the door glass bolt holes can be seen.


f.

Turn the power switch on (IG).


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

for Driver Side:

i.

Disconnect the multiplex network master switch assembly.



i.

for Front Passenger Side:

i.

Disconnect the power window regulator switch assembly.



j.
B471472C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Insert the front door glass sub-assembly into the front door panel along the front door glass run as shown in the illustration.


k.
B471439

Install the front door glass sub-assembly with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


l.
B471438

Install the hole plug.


Hide 67832 31.INSTALL FRONT DOOR SERVICE HOLE COVER

a.
B471437

Engage the 3 clips to install the front door service hole cover.


b.
B471473

Insert 4 front door weatherstrip clips and turn them 45 degrees as shown in the illustration to install them.


c.
B471435

Engage the 2 clamps.


Hide 86160 32.INSTALL FRONT NO. 1 SPEAKER ASSEMBLY

Hide 33.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER

Hide 87964 34.INSTALL OUTER MIRROR INSTALL HOLE COVER

Hide 89430A 36.INSTALL OUTER MIRROR CONTROL ECU ASSEMBLY

Hide 69206B 37.INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B471434

Engage the 3 claws to install the front door inside handle sub-assembly.


Hide 67838A 38.INSTALL FRONT DOOR VENT SEAL

a.
B471474C01
0,0 0,0 false
V113147

Install in this Direction


Install the front door vent seal to the front door inner glass weatherstrip.


Hide 39.INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP WITH FRONT DOOR VENT SEAL

a.
B471475C01
0,0 0,0 false
V113147

Install in this Direction


Install the front door inner glass weatherstrip with front door vent seal as shown in the illustration.


b.
B477384

Engage the clip.


Hide 67602 40.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

a.
B471476C01
2.219,1.208 2.635,0.927 true 2.115,1.646 2.469,1.906 true 2.635,0.813 2.875,1.01 0.24,0.198 10 true *1 2.479,1.844 2.719,2.042 0.24,0.198 10 true *2
*1 Front Door Inside Locking Cable Assembly
*2 Front Door Lock Remote Control Cable Assembly
V113147

Install in this Direction


Connect the front door lock remote control cable assembly and front door inside locking cable assembly to the front door inside handle sub-assembly as shown in the illustration.


b.
B471477

Engage the guide and 7 claws.


c.

Engage the 10 clips to install the front door trim board sub-assembly.


d.
B469213

Install the 3 screws.


Hide 81230 41.INSTALL COURTESY LIGHT ASSEMBLY

Hide 74220 42.INSTALL FRONT ARMREST ASSEMBLY

a.
B469211C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guide as shown in the illustration.


b.
B469209C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 3 clips, 8 claws and 3 guides to install the front armrest assembly as shown in the illustration.


Hide 43.INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

a.

Connect the connector.


b.
B471736C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guide as shown in the illustration.


c.
B469207C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 5 guides, 7 claws and clip to install the multiplex network master switch assembly with front door upper armrest base panel as shown in the illustration.


Hide 44.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)

a.

Connect the connector.


b.
B471742C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guide as shown in the illustration.


c.
B471721C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 5 guides, 7 claws and clip to install the power window regulator switch assembly with front door upper armrest base panel as shown in the illustration.


Hide 74038A 45.INSTALL FRONT DOOR ARMREST COVER SUB-ASSEMBLY

a.
B471478

Engage the 3 claws to install the front door armrest cover sub-assembly.


Hide 67492A 46.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH

a.
B469203

Engage the guide and clip to install the front door lower frame bracket garnish.


Hide 47.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 48.INITIALIZE POWER WINDOW CONTROL SYSTEM