Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › 2017.09–2021.02
RM33C0E _58 Vehicle Interior _065461 PRE-COLLISION _0332154 PRE-COLLISION SYSTEM C

PRE-COLLISION  PRE-COLLISION SYSTEM  U023A  Lost Communication With Image Processing Module "A"  


DESCRIPTION

The millimeter wave radar sensor assembly communicates with the forward recognition camera via CAN communication. If there is a communication error with the forward recognition camera, the millimeter wave radar sensor assembly stores DTC U023A.

DTC No. Detection Item DTC Detection Condition Trouble Area
U023A Lost Communication With Image Processing Module "A" When the power switch is on (IG), a communication error between the forward recognition camera and millimeter wave radar sensor assembly is detected for approximately 2 seconds.
·

CAN communication system

·

Forward recognition camera power source circuit

·

Forward recognition camera

·

Wire harness or connector



WIRING DIAGRAM

B472644E02
5.677,1.667 7.073,2.083 1.396,0.417 10 false Millimeter Wave Radar Sensor Assembly 5.677,1.49 6.135,1.688 0.458,0.198 10 false A30 3.625,1.667 4.875,2.042 1.25,0.375 10 false Forward Recognition Camera 3.615,1.5 4.073,1.698 0.458,0.198 10 false V6 6.021,0.417 6.635,0.615 0.615,0.198 10 false CA1P 6.01,1.177 6.625,1.375 0.615,0.198 10 false CA1N 4.479,0.417 5.094,0.615 0.615,0.198 10 false CANH 4.51,1.177 5.125,1.375 0.615,0.198 10 false CANL 5.833,0.417 5.99,0.615 0.156,0.198 10 false 5 5.833,1.177 5.99,1.375 0.156,0.198 10 false 6 4.948,1.188 5.219,1.417 0.271,0.229 10 false 12 4.969,0.417 5.125,0.615 0.156,0.198 10 false 6 3.625,1.073 4.073,1.271 0.448,0.198 10 false GND 3.625,0.521 4.24,0.719 0.615,0.198 10 false IGB 3.448,0.417 3.604,0.615 0.156,0.198 10 false 7 3.375,0.948 3.635,1.167 0.26,0.219 10 false 10 2.344,0.677 3.719,0.875 1.375,0.198 10 false ECU-IG1 NO. 3 0.354,0.531 3.417,0.729 3.063,0.198 10 false from IG1-NO. 1 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.READ VALUE USING GTS (CAN BUS CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Can Bus Check.

CAN Bus Check
50007

Result:
Result Proceed to
All of the ECUs and sensors that are currently connected to the CAN communication system are displayed A
None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed B



A

2.CHECK FOR DTCs (PRE-COLLISION SYSTEM)

B

2.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
a.

Clear the DTCs.

Body Electrical > Pre-Collision 2 > Clear DTCs
50002 220

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the power switch on (IG) and wait 2 seconds or more.




c.

Check for DTCs.

Body Electrical > Pre-Collision 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC U1002 is not output A
DTC U1002 is output B



A

3.CHECK FOR OPEN IN CAN BUS LINES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - FORWARD RECOGNITION CAMERA)

B

3.CHECK FOR OPEN IN CAN BUS LINES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - FORWARD RECOGNITION CAMERA)
a.

Disconnect the V6 forward recognition camera connector.


b.

Disconnect the A30 millimeter wave radar sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V6-6 (CANH) - A30-5 (CA1P) Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
V6-12 (CANL) - A30-6 (CA1N) Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



d.

Connect the A30 millimeter wave radar sensor assembly connector.


e.

Connect the V6 forward recognition camera connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE)

NG

REPAIR OR REPLACE CAN BUS LINE OR CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - FORWARD RECOGNITION CAMERA)

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE)
a.
A380142C64
1.521,0.167 1.875,0.417 0.354,0.25 0.917,1.542 1.26,1.385 true 1.802,1.427 1.854,1.771 true 0.146,0.125 0.458,0.281 0.313,0.156 10 false *a 1.615,0.208 1.927,0.406 0.313,0.198 10 false V6 0.646,1.469 1.104,1.667 0.458,0.198 10 false IGB 1.74,1.781 2.198,1.979 0.458,0.198 10 false GND
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the V6 forward recognition camera connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V6-10 (GND) - Body ground Always Below 1 Ω



c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
V6-7 (IGB) - Body ground Power switch on (IG) 11 to 14 V



e.

Connect the V6 forward recognition camera connector.


Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)