Refer to DTC P052012.
Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>P052012
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P052024 | Engine Oil Pressure Sensor/Switch "A" Signal Stuck High | The oil pressure sensor output voltage is higher than the threshold value (1 trip detection logic). | ·
Open or short in oil pressure sensor (oil pressure sender gauge assembly) circuit ·
Oil pressure sensor (oil pressure sender gauge assembly) ·
ECM |
Comes on | DTC stored | SAE Code: P0521 |
| P05202A | Engine Oil Pressure Sensor/Switch "A" Signal Stuck in Range | The oil pressure sensor output voltage is the same value for a certain period of time (1 trip detection logic). | ·
Open or short in oil pressure sensor (oil pressure sender gauge assembly) circuit ·
Oil pressure sensor (oil pressure sender gauge assembly) ·
ECM |
Comes on | DTC stored | SAE Code: P0521 |
| DTC No. | Data List |
|---|---|
| P052024 | ·
Engine Oil Temperature Sensor ·
Engine Oil Pressure |
| P05202A |
The ECM calculates the engine oil pressure based on the output voltage of the oil pressure sensor. If any of the following are detected, the ECM will illuminate the MIL and store a DTC.
The oil pressure sensor output value differs from the specified value for a given engine speed (P052024).
The oil pressure sensor output voltage does not change for a certain period of time (P05202A).
| Frequency of Operation | Continuous |
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in Inspection Mode (Maintenance Mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with all the accessories switched off [A].
When the vehicle is stationery, gently depress the accelerator pedal until the engine speed increases to 2500 rpm for 30 seconds, then release the accelerator pedal to return to the idling speed [B].
Repeat step [B] 3 times or more.
Enter the following menus: Powertrain / Engine / Trouble Codes [C].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P052024 or P05202A.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system is malfunctioning.
If the judgment result is INCOMPLETE, perform steps [B] through [C] again.
Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.
(Select Powertrain in Health Check and then check the time stamp data.)
If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P052024 or P05202A is output | A |
| DTC P052024 or P05202A and other DTCs are output | B |
If any DTCs other than P052024 or P05202A are output, troubleshoot those DTCs first.
A
B
Read the value displayed on the GTS.
Disconnect the oil pressure control valve assembly connector.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in Inspection Mode (Maintenance Mode).
| Tester Display |
|---|
| Inspection Mode |
Start the engine.
Enter the following menus: Powertrain / Engine / Data List / Engine Oil Temperature Sensor and Engine Oil Pressure.
| Tester Display |
|---|
| Engine Oil Temperature Sensor |
| Engine Oil Pressure |
With the engine oil temperature at 75 to 85°C (167 to 185°F), read the "Engine Oil Pressure" with the engine speed at 2500 rpm.
Read the oil pressure using an oil pressure gauge with adapter.
Install the oil pressure gauge with adapter.
Click hereEngine / Hybrid System>A25A-FXS (LUBRICATION)>OIL PRESSURE SENSOR>REMOVAL
Removing the oil pressure sender gauge assembly while the engine is hot could result in burns caused by contact with hot engine oil.
Clean the hose and adapter of the oil pressure gauge before and after measurement.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in Inspection Mode (Maintenance Mode).
| Tester Display |
|---|
| Inspection Mode |
Start the engine.
With the engine oil temperature at 75 to 85°C (167 to 185°F), read the oil pressure gauge with the engine speed at 2500 rpm.
Compare the Data List value and the oil pressure gauge reading.
Data List value and gauge reading are within +/-50 kPa (7.3 psi) of each other
Be sure to clear the DTCs after reinstalling the oil pressure sensor (oil pressure sender gauge assembly) or reconnecting the oil pressure sensor (oil pressure sender gauge assembly) or oil pressure control valve assembly connector, as DTCs may be stored.
| Proceed to |
|---|
| OK |
| NG |
OK
NG