Home › Engine / Hybrid System › A25A-FXS (ENGINE CONTROL) › SFI SYSTEM (w/ Canister Pump Module)
RM33C0E _51 Engine / Hybrid System _065419 A25A-FXS ENGINE CONTROL _0332275 SFI SYSTEM(w/ Canister Pump Module) J

A25A-FXS ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  Ignition Circuit  


DESCRIPTION

A direct ignition system is used on this vehicle. The direct ignition system is a 1 cylinder ignition system which ignites one cylinder with one ignition coil. In the 1 cylinder ignition system, one spark plug is connected to the end of the secondary winding. High voltage is generated in the secondary winding and is applied directly to the spark plug. The spark of the spark plug passes from the center electrode to the ground electrode.

The ECM determines the ignition timing and transmits the ignition signals for each cylinder. Using the ignition signal, the ECM turns on and off the power transistor inside the igniter, which switches on and off a current to the primary coil. When the current to the primary coil is cut off, high voltage is generated in the secondary coil and this voltage is applied to the spark plugs to create sparks inside the cylinders.

WIRING DIAGRAM

A404775E02
5.906,6.094 6.469,6.385 0.563,0.292 10 false C100 6.365,6.094 6.823,6.292 0.458,0.198 10 false ECM 5.875,0.635 6.49,0.833 0.615,0.198 10 false IGT1 5.625,0.646 5.938,0.844 0.313,0.198 10 false 49 5.635,2.271 5.948,2.469 0.313,0.198 10 false 48 5.875,2.26 6.49,2.458 0.615,0.198 10 false IGT2 5.646,3.854 5.958,4.052 0.313,0.198 10 false 47 5.875,3.844 6.49,4.042 0.615,0.198 10 false IGT3 5.656,5.365 5.969,5.563 0.313,0.198 10 false 46 5.896,5.344 6.51,5.542 0.615,0.198 10 false IGT4 4.969,0.646 5.125,0.844 0.156,0.198 10 false 2 4.979,2.24 5.135,2.438 0.156,0.198 10 false 2 4.958,3.854 5.115,4.052 0.156,0.198 10 false 2 4.948,5.365 5.104,5.563 0.156,0.198 10 false 2 4.563,0.75 5.177,0.948 0.615,0.198 10 false IGT1 4.573,2.365 5.188,2.563 0.615,0.198 10 false IGT2 4.573,3.958 5.188,4.156 0.615,0.198 10 false IGT3 4.583,5.469 5.198,5.667 0.615,0.198 10 false IGT4 3.948,0.75 4.26,0.948 0.313,0.198 10 false +B 3.781,0.625 3.938,0.823 0.156,0.198 10 false 1 3.781,2.25 3.938,2.448 0.156,0.198 10 false 1 3.74,3.823 3.896,4.021 0.156,0.198 10 false 1 3.76,5.385 3.917,5.583 0.156,0.198 10 false 1 3.948,2.365 4.26,2.563 0.313,0.198 10 false +B 3.927,3.958 4.24,4.156 0.313,0.198 10 false +B 3.948,5.458 4.26,5.656 0.313,0.198 10 false +B 3.781,0.979 3.938,1.177 0.156,0.198 10 false 3 3.76,2.573 3.938,2.833 0.177,0.26 10 false 3 3.76,4.167 3.917,4.365 0.156,0.198 10 false 3 3.76,5.74 3.917,5.938 0.156,0.198 10 false 3 3.927,1.073 4.385,1.271 0.458,0.198 10 false GND 3.927,2.688 4.385,2.885 0.458,0.198 10 false GND 3.927,4.271 4.385,4.469 0.458,0.198 10 false GND 3.938,5.885 4.396,6.083 0.458,0.198 10 false GND 3.427,1.458 3.74,1.656 0.313,0.198 10 false C2 3.438,1.656 5.938,2.052 2.5,0.396 10 false Ignition Coil Assembly (No. 1 Cylinder) 3.458,3.073 3.771,3.271 0.313,0.198 10 false C4 3.469,3.271 5.875,3.563 2.406,0.292 10 false Ignition Coil Assembly (No. 2 Cylinder) 3.438,4.667 3.75,4.865 0.313,0.198 10 false C8 3.438,4.865 5.896,5.313 2.458,0.448 10 false Ignition Coil Assembly (No. 3 Cylinder) 3.531,6.219 3.99,6.417 0.458,0.198 10 false C11 3.51,6.427 5.969,6.781 2.458,0.354 10 false Ignition Coil Assembly (No. 4 Cylinder) 2.615,0.927 3.073,1.125 0.458,0.198 10 false INJ 1.969,0.625 2.125,0.823 0.156,0.198 10 false 3 1.958,1.125 2.115,1.323 0.156,0.198 10 false 1 1.208,1.146 1.365,1.344 0.156,0.198 10 false 2 1.208,0.625 1.365,0.823 0.156,0.198 10 false 5 1.271,1.604 2.646,1.802 1.375,0.198 10 false IG2 NO. 1 0.427,2.729 1.656,2.927 1.229,0.198 10 false IG2-MAIN 1.667,3.698 2.281,3.896 0.615,0.198 10 false IG1D 2.083,3.698 2.396,3.896 0.313,0.198 10 false 17 0.427,4.74 1.042,4.938 0.615,0.198 10 false MAIN 0.938,4.115 1.396,4.313 0.458,0.198 10 false K62 0.917,4.302 2.75,4.906 1.833,0.604 10 false Certification ECU (Smart Key ECU Assembly) 0.563,5.563 1.729,5.875 1.167,0.313 10 false Auxiliary Battery

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Perform a spark test before proceeding. If there is no spark for any cylinder, inspect this circuit.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION


PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)
A402447C01
0.281,0.469 0.688,0.688 0.406,0.219 0.281,0.813 0.688,1.031 0.406,0.219 0.281,1.146 0.688,1.365 0.406,0.219 0.281,1.479 0.688,1.698 0.406,0.219 0.948,1.719 1.365,1.302 false 2.521,1.708 2.104,1.302 false 0.167,0.156 0.479,0.354 0.313,0.198 10 false *a 0.74,1.667 1.052,1.865 0.313,0.198 10 false +B 2.583,1.667 2.896,1.865 0.313,0.198 10 false GND 0.406,0.51 0.719,0.708 0.313,0.198 10 false C2 0.406,0.844 0.719,1.042 0.313,0.198 10 false C4 0.406,1.167 0.719,1.365 0.313,0.198 10 false C8 0.375,1.51 0.688,1.708 0.313,0.198 10 false C11
*a Front view of wire harness connector
(to Ignition Coil Assembly)


a.

Disconnect the ignition coil assembly connectors.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C2-1 (+B) - C2-3 (GND) Power switch on (IG) 11 to 14 V
C4-1 (+B) - C4-3 (GND) Power switch on (IG) 11 to 14 V
C8-1 (+B) - C8-3 (GND) Power switch on (IG) 11 to 14 V
C11-1 (+B) - C11-3 (GND) Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
a.

Disconnect the ignition coil assembly connectors.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C2-2 (IGT1) - C100-49 (IGT1) Always Below 1 Ω
C4-2 (IGT2) - C100-48 (IGT2) Always Below 1 Ω
C8-2 (IGT3) - C100-47 (IGT3) Always Below 1 Ω
C11-2 (IGT4) - C100-46 (IGT4) Always Below 1 Ω
C2-2 (IGT1) or C100-49 (IGT1) - Body ground and other terminals Always 10 kΩ or higher
C4-2 (IGT2) or C100-48 (IGT2) - Body ground and other terminals Always 10 kΩ or higher
C8-2 (IGT3) or C100-47 (IGT3) - Body ground and other terminals Always 10 kΩ or higher
C11-2 (IGT4) or C100-46 (IGT4) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
a.

Disconnect the ignition coil assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C2-3 (GND) - Body ground Always Below 1 Ω
C4-3 (GND) - Body ground Always Below 1 Ω
C8-3 (GND) - Body ground Always Below 1 Ω
C11-3 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (IG2 NO. 1 RELAY - IGNITION COIL ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (IG2 NO. 1 RELAY - IGNITION COIL ASSEMBLY)
a.

Disconnect the IG2 NO. 1 relay from No. 1 engine room relay block and No. 1 junction block assembly.


b.

Disconnect the ignition coil assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (IG2 NO. 1 relay) - C2-1 (+B) Always Below 1 Ω
3 (IG2 NO. 1 relay) - C4-1 (+B) Always Below 1 Ω
3 (IG2 NO. 1 relay) - C8-1 (+B) Always Below 1 Ω
3 (IG2 NO. 1 relay) - C11-1 (+B) Always Below 1 Ω
3 (IG2 NO. 1 relay) or C2-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
3 (IG2 NO. 1 relay) or C4-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
3 (IG2 NO. 1 relay) or C8-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
3 (IG2 NO. 1 relay) or C11-1 (+B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR