Home › Engine / Hybrid System › A25A-FXS (ENGINE CONTROL) › SFI SYSTEM (w/ Canister Pump Module)
RM33C0E _51 Engine / Hybrid System _065419 A25A-FXS ENGINE CONTROL _0332275 SFI SYSTEM(w/ Canister Pump Module) C

A25A-FXS ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P00B111  Radiator Coolant Temperature Sensor Circuit Short to Ground  


DESCRIPTION

The No. 2 engine coolant temperature sensor is installed to the radiator pipe between the engine and radiator and monitors the thermostat operation.

The structure of the thermistor used in the No. 2 engine coolant temperature sensor and its connection to the ECM are the same as those of the intake air temperature sensor.

Refer to DTC P011011.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>P011011

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P00B111 Radiator Coolant Temperature Sensor Circuit Short to Ground The No. 2 engine coolant temperature sensor output voltage is less than 0.081 V for 3 seconds or more (1 trip detection logic).
·

Short in No. 2 engine coolant temperature sensor circuit

·

No. 2 engine coolant temperature sensor

·

ECM


Comes on DTC stored SAE Code: P00B3

MONITOR DESCRIPTION

The No. 2 engine coolant temperature sensor is used to monitor the engine coolant temperature. The No. 2 engine coolant temperature sensor has a thermistor with a resistance that varies according to the temperature of the engine coolant. When the engine coolant temperature is low, the resistance in the thermistor increases. When the temperature is high, the resistance decreases. These variations in resistance are reflected in the output voltage from the sensor. The ECM monitors the sensor voltage and uses this value to calculate the engine coolant temperature. If the No. 2 engine coolant temperature sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction of the No. 2 engine coolant temperature sensor circuit, illuminates the MIL and stores a DTC.

Example:

If the No. 2 engine coolant temperature sensor output voltage is less than 0.081 V for 3 seconds or more, the ECM store this DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG).

7.

Turn the GTS on.

8.

Wait 3 seconds or more.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P00B111.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A408013E02
0.104,2.76 2.781,3.115 2.677,0.354 10 false No. 2 Engine Coolant Temperature Sensor 0.083,2.604 2.073,2.802 1.99,0.198 10 false C46 2.219,1.323 2.729,1.521 0.51,0.198 10 false 2 2.229,1.927 4.219,2.125 1.99,0.198 10 false 1 4.927,1.333 5.438,1.531 0.51,0.198 10 false 129 4.917,1.917 5.427,2.115 0.51,0.198 10 false 130 5.552,2.99 6.063,3.188 0.51,0.198 10 false C100 6.031,2.99 6.458,3.24 0.427,0.25 10 false ECM 5.271,1.323 5.781,1.521 0.51,0.198 10 false THTW 5.271,1.927 5.781,2.125 0.51,0.198 10 false ETHT 5.896,0.938 6.406,1.135 0.51,0.198 10 false 5 V 5.854,1.229 6.365,1.427 0.51,0.198 10 false R 1.698,1.323 2.208,1.521 0.51,0.198 10 false THW3 1.896,1.927 2.406,2.125 0.51,0.198 10 false E2

CAUTION / NOTICE / HINT

NOTICE:
·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY



HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT NO. 2 ENGINE COOLANT TEMPERATURE SENSOR
a.

Inspect the No. 2 engine coolant temperature sensor.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION

Result:
Proceed to
OK
NG




OK

2.CHECK HARNESS AND CONNECTOR (NO. 2 ENGINE COOLANT TEMPERATURE SENSOR - ECM)

NG

REPLACE NO. 2 ENGINE COOLANT TEMPERATURE SENSOR

2.CHECK HARNESS AND CONNECTOR (NO. 2 ENGINE COOLANT TEMPERATURE SENSOR - ECM)
a.

Disconnect the No. 2 engine coolant temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C46-2 (THW3) or C100-129 (THTW) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR