Home › Engine / Hybrid System › A25A-FXS (ENGINE CONTROL) › SFI SYSTEM (w/ Canister Pump Module) › 2017.09–2020.08
RM33C0E _51 Engine / Hybrid System _065419 A25A-FXS ENGINE CONTROL _0332275 SFI SYSTEM(w/ Canister Pump Module) C

A25A-FXS ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P059F73  Active Grille Air Shutter "A" Actuator Stuck Closed  P05A072  Active Grille Air Shutter "A" Actuator Stuck Open  


DESCRIPTION

The grille shutter system is composed of the radiator shutter sub-assembly and grille shutter ECU (swing grille actuator assembly).

When the certain vehicle conditions are met, the grille shutter system operates the swing grille actuator assembly to open and close the radiator shutter sub-assembly and control the volume of air flowing through the radiator assembly into the engine compartment. This results in increased thermal efficiency and increased fuel economy due to reduced aerodynamic drag. This control is performed based on signals received via CAN communication: vehicle speed signal, engine coolant temperature signal, hybrid inverter coolant temperature signal, ambient temperature signal and refrigerant pressure.

If the grille shutter ECU (swing grille actuator assembly) detects a malfunction in itself or any of the mechanical components of the grille shutter system, it will output a malfunction signal to the ECM and the ECM will store a DTC.

Control List
Control Description
Closing Operation Control The grille shutter closes when certain conditions related to the vehicle speed, engine coolant temperature, inverter coolant temperature, ambient temperature and refrigerant pressure are met.
Opening Operation Control The grille shutter opens when certain conditions related to the vehicle speed, engine coolant temperature, inverter coolant temperature, ambient temperature and refrigerant pressure are met.
Power Switch Off-linked Opening Operation Control Opens the grille shutter when the power switch is turned off in order to prevent the grille shutter from becoming stuck closed while the vehicle is stopped.
Power Switch On (IG) Closing/Opening Operation If the detection conditions of a DTC are met during a trip, the next time the power switch is turned on (IG), a grille shutter opening and closing operation will be performed in order to judge if the malfunction still exists.
Winter Control Mode Stops the grille shutter at a position other than the fully closed position and suspends grille shutter operation in order to prevent it from becoming stuck closed when the ambient temperature is 5°C (41°F) or lower. Winter control mode is canceled when the ambient temperature becomes 10°C (50°F) or higher.
Retry Operation If a mechanical malfunction is detected during a grille shutter operation, the operation will be attempted again.

A379607E02
4.125,0.75 4.292,0.542 4.292,0.542 4.469,0.542 false 1.5,6.313 3.948,6.51 2.448,0.198 10 false End Shaft Switch 4.552,0.469 6.563,0.823 2.01,0.354 10 false Grille Shutter Motor (Swing Grille Actuator Assembly) 5.854,2.302 6.313,2.5 0.458,0.198 10 false CPU 3.76,2.469 4.875,2.792 1.115,0.323 10 false Motor Driver 3.552,1.573 4.677,1.75 1.125,0.177 10 false Motor Drive Circuit 3.667,3.354 4.646,3.698 0.979,0.344 10 false Power Supply Voltage Monitor Circuit 3.49,4.729 4.813,4.885 1.323,0.156 10 false Power Supply Circuit 3.729,5.542 4.646,5.74 0.917,0.198 10 false Switch Circuit 2.74,5.688 3.354,5.885 0.615,0.198 10 false SEN1 2.75,5.906 3.365,6.104 0.615,0.198 10 false SEN2 0.052,4.573 0.802,4.896 0.75,0.323 10 false from ECU-B NO. 2 Fuse 2.26,4.396 2.573,4.594 0.313,0.198 10 false +B 5.458,5.75 6.073,5.948 0.615,0.198 10 false SEN1 5.469,5.99 6.083,6.188 0.615,0.198 10 false SEN2 2.198,5.104 2.656,5.302 0.458,0.198 10 false GND

A379608E02
0.042,1.156 1.01,1.688 0.969,0.531 10 false to CAN Communication System 0.781,6.25 4.448,6.448 3.667,0.198 10 false : CAN Communication Line 3.063,6.104 5.031,6.313 1.969,0.208 10 false Radiator Shutter Sub-assembly 2.875,5.458 6.375,5.698 3.5,0.24 10 false Grille Shutter ECU (Swing Grille Actuator Assembly) 2.094,0.99 2.708,1.188 0.615,0.198 10 false CAN-P 2.083,1.396 2.698,1.594 0.615,0.198 10 false CAN-N 3.438,0.833 4.729,1.208 1.292,0.375 10 false CAN Communication Circuit 5.865,0.583 6.323,0.781 0.458,0.198 10 false CPU 3.469,2.583 4.771,2.948 1.302,0.365 10 false Hall IC Power Supply Circuit 3.885,3.656 4.344,3.865 0.458,0.208 10 false Hall IC 5.448,3.635 6.083,3.833 0.635,0.198 10 false Hall IC1 5.458,3.854 6.094,4.052 0.635,0.198 10 false Hall IC2 3.771,4.479 4.688,4.677 0.917,0.198 10 false Clock Circuit

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P059F73 Active Grille Air Shutter "A" Actuator Stuck Closed All of the following conditions are met and the ECM receives a malfunction signal 17 times* (2 trip detection logic):
·

Grille shutter locking is detected.

·

The grille shutter is not within the normal closing operation judgment area.

·

The grille shutter operation was reattempted once.

·

Grille shutter closing operation malfunction judgment has occurred once or more.


·

Radiator shutter sub-assembly

·

Swing grille actuator assembly


Comes on DTC stored SAE Code: P059F
P05A072 Active Grille Air Shutter "A" Actuator Stuck Open All of the following conditions are met and the ECM receives a malfunction signal 17 times* (2 trip detection logic):
·

Grille shutter locking is detected.

·

The grille shutter is not within the normal opening operation judgment area.

·

The grille shutter operation was reattempted once.

·

Grille shutter opening operation malfunction judgment has occurred once or more.


·

Radiator shutter sub-assembly

·

Swing grille actuator assembly


Comes on DTC stored SAE Code: P05A0

HINT:

*: For every 65 ms that the ECM receives a grille shutter system malfunction signal from the grille shutter ECU (swing grille actuator assembly) the ECM determines it has received the signal 1 time. If the ECM determines the malfunction signal has been received 17 consecutive times (the signal is received for approximately 1 second continuously), it will store a DTC.


MONITOR DESCRIPTION

If the grille shutter ECU (swing grille actuator assembly) detects that the grille shutter has stopped during an opening or closing operation, due to foreign matter or a malfunction, it will send a malfunction signal to the ECM and the ECM will store a DTC.

Detection Condition DTC No.
Closing Operation P059F73 (Active Grille Air Shutter "A" Actuator Stuck Closed)
Opening Operation P05A072 (Active Grille Air Shutter "A" Actuator Stuck Open)

MONITOR STRATEGY

Related DTCs P059F: Active grille air shutter stuck off
P05A0: Active grille air shutter stuck on
Required Sensors/Components (Main) Swing grille actuator assembly
Radiator shutter sub-assembly
Required Sensors/Components (Related) -
Frequency of Operation Continuous
Duration 17 times
MIL Operation 2 driving cycles
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

P059F73
Monitor runs whenever the following DTCs are not stored None
Auxiliary battery voltage 10.5 to 16 V
Command to close active grille air shutter On
Active grille air shutter motor speed sensor range check fail Not occurred
Shutter control timeout condition (*1) Not met
Active grille air shutter Control Circuit fail Not occurred
Lost communication with hybrid control module Not occurred
Active grille air shutter control module fail Not occurred
Motor lock condition (*2) Met
Active grille air shutter first operation Close
Either of the following conditions is met 1 or 2
1. Number of active grille air shutter motor speed sensor 1 signal pulse 1 time or more
2. Time after active grille air shutter open control is operated 0.61 seconds or more

P05A072
Monitor runs whenever the following DTCs are not stored None
Auxiliary battery Voltage 10.5 to 16 V
Command to open active grille air shutter On
Active grille air shutter motor speed sensor range check fail Not occurred
Shutter control timeout condition (*1) Not met
Active grille air shutter Control Circuit fail Not occurred
Lost communication with hybrid control module Not occurred
Active grille air shutter control module fail Not occurred
Motor lock condition (*2) Met
Either of the following conditions is met 1 or 2
1. Number of active grille air shutter motor speed sensor 1 signal pulse 1 time or more
2. Time after active grille air shutter close control is operated 0.61 seconds or more

*1: Shutter control timeout condition judgment -
Either of the following conditions is met 1 or 2
1. Time after active grille air shutter close control is operated 11 seconds or more
2. Time after active grille air shutter open control is operated 11 seconds or more

*2: Motor lock condition judgment -
Either of the following conditions is met 1 or 2
1. All of the following conditions are met -
Number of active grille air shutter motor speed sensor 1 signal pulse Less than 24 times
Pulse period of active grille air shutter motor speed sensor 1 signal 0.61 seconds or more
Pulse period of active grille air shutter motor speed sensor 2 signal 0.61 seconds or more
2. All of the following conditions are met -
Number of active grille air shutter motor speed sensor 1 signal pulse 24 times or more
Pulse period of active grille air shutter motor speed sensor 1 signal 0.25 seconds or more
Pulse period of active grille air shutter motor speed sensor 2 signal 0.25 seconds or more

TYPICAL MALFUNCTION THRESHOLDS

P059F73
All of the following conditions are met -
Active grille air shutter first operation Close
Number of active grille air shutter motor speed sensor 1 signal pulse 1 time or more

P05A072
All of the following conditions are met -
Active grille air shutter first operation Open
Number of active grille air shutter motor speed sensor 1 signal pulse 1 time or more

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG).

7.

Turn the GTS on.

8.

Enter the following menus: Body Electrical / Grill Shutter / Utility / Grill Shutter Control Mode Switching.

9.

According to the display on the GTS, change the grille shutter control mode from normal mode to maintenance mode.

10.

Enter the following menus: Body Electrical / Grill Shutter / Active Test / Shutter Closing Operation Lock Detection / Data List / Shutter Operation Lock Detection Result for Active Test.

11.

According to the display on the GTS, perform the Active Test and read the value of Data List item Shutter Operation Lock Detection Result for Active Test.

OK:

"Normal" is displayed.


12.

Enter the following menus: Body Electrical / Grill Shutter / Active Test / Shutter Opening Operation Lock Detection / Data List / Shutter Operation Lock Detection Result for Active Test.

13.

According to the display on the GTS, perform the Active Test and read the value of Data List item Shutter Operation Lock Detection Result for Active Test.

OK:

"Normal" is displayed.



WIRING DIAGRAM

A404766E15
0.583,3.417 2.625,3.698 2.042,0.281 10 false : CAN Communication Line 0.74,2.292 1.969,2.667 1.229,0.375 10 false Auxiliary Battery 0.552,1.385 1.167,1.583 0.615,0.198 10 false MAIN 0.792,0.656 1.563,0.854 0.771,0.198 10 false J/B-B 1.521,0.656 2.833,0.99 1.313,0.333 10 false ECU-B NO. 2 5.833,0.385 5.99,0.583 0.156,0.198 10 false 4 6.021,0.49 6.333,0.688 0.313,0.198 10 false +B 5.833,0.854 5.99,1.052 0.156,0.198 10 false 2 6.021,1.021 6.635,1.219 0.615,0.198 10 false CAN-P 5.823,1.365 5.979,1.563 0.156,0.198 10 false 3 6.01,1.552 6.625,1.75 0.615,0.198 10 false CAN-N 5.823,1.938 5.979,2.135 0.156,0.198 10 false 1 6.01,2.052 6.469,2.25 0.458,0.198 10 false GND 1.594,1.26 4.063,1.771 2.469,0.51 10 false to CAN Communication System 5.198,3.083 7.156,3.344 1.958,0.26 10 false Radiator Shutter Sub-assembly 5.198,2.917 5.656,3.115 0.458,0.198 10 false A41

CAUTION / NOTICE / HINT

NOTICE:
·

In order to ensure safety, before performing troubleshooting or removing the swing grille actuator assembly or radiator shutter sub-assembly, change the grille shutter control mode to maintenance mode.

·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY



HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM UTILITY USING GTS (GRILL SHUTTER CONTROL MODE SWITCHING)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Grill Shutter / Utility / Grill Shutter Control Mode Switching.

Body Electrical > Grill Shutter > Utility
Tester Display
Grill Shutter Control Mode Switching
50005 352 4221

e.

According to the display on the GTS, change the grille shutter control mode from normal mode to maintenance mode.


Result:
Proceed to
NEXT



NEXT

2.INSPECT GRILLE SHUTTER (FOREIGN MATTER AND ICE)
2.INSPECT GRILLE SHUTTER (FOREIGN MATTER AND ICE)
a.

Check the area around the shutters and the links of the grille shutter for foreign matter and ice.

OK:

No foreign matter or ice.



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS (GRILLE SHUTTER OPERATION)

NG

8.REMOVE FOREIGN MATTER OR ICE (CLEAN GRILLE SHUTTER)
3.PERFORM ACTIVE TEST USING GTS (GRILLE SHUTTER OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Grill Shutter / Active Test / Shutter Closing Operation Lock Detection / Data List / Shutter Operation Lock Detection Result for Active Test.

Body Electrical > Grill Shutter > Active Test
Active Test Display
Shutter Closing Operation Lock Detection
Data List Display
Shutter Operation Lock Detection Result for Active Test
50004 352 3 8

e.

According to the display on the GTS, perform the Active Test and read the value of Data List item Shutter Operation Lock Detection Result for Active Test.

OK:

"Normal" is displayed.



f.

Enter the following menus: Body Electrical / Grill Shutter / Active Test / Shutter Opening Operation Lock Detection / Data List / Shutter Operation Lock Detection Result for Active Test.

Body Electrical > Grill Shutter > Active Test
Active Test Display
Shutter Opening Operation Lock Detection
Data List Display
Shutter Operation Lock Detection Result for Active Test
50004 352 4 8

g.

According to the display on the GTS, perform the Active Test and read the value of Data List item Shutter Operation Lock Detection Result for Active Test.

OK:

"Normal" is displayed.



HINT:

When the value of Data List item Shutter Operation Lock Detection Result for Active Test is "Normal", it can be determined that the grille shutter system has returned to normal.


Result:
Proceed to
OK
NG



OK

4.CLEAR DTC

NG

6.PERFORM ACTIVE TEST USING GTS (SWING GRILLE ACTUATOR ASSEMBLY OPERATION)
4.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

f.

Turn the power switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

5.PERFORM UTILITY USING GTS (GRILL SHUTTER CONTROL MODE SWITCHING)
5.PERFORM UTILITY USING GTS (GRILL SHUTTER CONTROL MODE SWITCHING)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Grill Shutter / Utility / Grill Shutter Control Mode Switching.

Body Electrical > Grill Shutter > Utility
Tester Display
Grill Shutter Control Mode Switching
50005 352 4221

e.

According to the display on the GTS, change the grille shutter control mode from maintenance mode to normal mode.


f.

Check for DTCs and make sure that DTC B1333 is not output.

Body Electrical > Grill Shutter > Trouble Codes
50001 352

Result:
Proceed to
NEXT



NEXT

END

6.PERFORM ACTIVE TEST USING GTS (SWING GRILLE ACTUATOR ASSEMBLY OPERATION)
a.

Remove the radiator shutter sub-assembly.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER>REMOVAL


b.

Remove the swing grille actuator assembly.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER>DISASSEMBLY


c.

Reconnect the swing grille actuator assembly connector.


d.

Connect the GTS to the DLC3.


e.

Turn the power switch on (IG).


f.

Turn the GTS on.


g.

Enter the following menus: Body Electrical / Grill Shutter / Active Test / Shutter Closing Operation Lock Detection.

Body Electrical > Grill Shutter > Active Test
Tester Display
Shutter Closing Operation Lock Detection
50004 352 3

h.

According to the display on the GTS, perform the Active Test and check the operation of the swing grille actuator assembly.

OK:

Operation is normal.



i.

Enter the following menus: Body Electrical / Grill Shutter / Active Test / Shutter Opening Operation Lock Detection.

Body Electrical > Grill Shutter > Active Test
Tester Display
Shutter Opening Operation Lock Detection
50004 352 4

j.

According to the display on the GTS, perform the Active Test and check the operation of the swing grille actuator assembly.

OK:

Operation is normal.



HINT:

Perform "Grill Shutter Control Mode Switching and Grill Shutter Initialization" after replacing the swing grille actuator assembly.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER SYSTEM>INITIALIZATION


Result:
Proceed to
OK
NG



OK

7.INSPECT RADIATOR SHUTTER SUB-ASSEMBLY (GRILLE SHUTTER OPERATION)

NG

REPLACE SWING GRILLE ACTUATOR ASSEMBLY

7.INSPECT RADIATOR SHUTTER SUB-ASSEMBLY (GRILLE SHUTTER OPERATION)
a.

Remove the radiator shutter sub-assembly.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER>REMOVAL


b.

Remove the swing grille actuator assembly.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER>DISASSEMBLY


c.

Manually open and close the radiator shutter sub-assembly and check that it moves smoothly.

OK:

Radiator shutter sub-assembly moves smoothly.



HINT:

Perform "Grill Shutter Control Mode Switching and Grill Shutter Initialization" after replacing the swing grille actuator assembly or radiator shutter sub-assembly.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER SYSTEM>INITIALIZATION


Result:
Proceed to
OK
NG



OK

REPLACE SWING GRILLE ACTUATOR ASSEMBLY

NG

REPLACE RADIATOR SHUTTER SUB-ASSEMBLY

8.REMOVE FOREIGN MATTER OR ICE (CLEAN GRILLE SHUTTER)
a.

Remove any foreign matter and/or ice from the area around the shutters and the links of the grille shutter.


Result:
Proceed to
NEXT



NEXT

9.PERFORM ACTIVE TEST USING GTS (GRILLE SHUTTER OPERATION)
9.PERFORM ACTIVE TEST USING GTS (GRILLE SHUTTER OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Grill Shutter / Active Test / Shutter Closing Operation Lock Detection / Data List / Shutter Operation Lock Detection Result for Active Test.

Body Electrical > Grill Shutter > Active Test
Active Test Display
Shutter Closing Operation Lock Detection
Data List Display
Shutter Operation Lock Detection Result for Active Test
50004 352 3 8

e.

According to the display on the GTS, perform the Active Test and read the value of Data List item Shutter Operation Lock Detection Result for Active Test.

OK:

"Normal" is displayed.



f.

Enter the following menus: Body Electrical / Grill Shutter / Active Test / Shutter Opening Operation Lock Detection / Data List / Shutter Operation Lock Detection Result for Active Test.

Body Electrical > Grill Shutter > Active Test
Active Test Display
Shutter Opening Operation Lock Detection
Data List Display
Shutter Operation Lock Detection Result for Active Test
50004 352 4 8

g.

According to the display on the GTS, perform the Active Test and read the value of Data List item Shutter Operation Lock Detection Result for Active Test.

OK:

"Normal" is displayed.



HINT:

When the value of Data List item Shutter Operation Lock Detection Result for Active Test is "Normal", it can be determined that the grille shutter system has returned to normal.


Result:
Proceed to
OK
NG



OK

10.CLEAR DTC

NG

6.PERFORM ACTIVE TEST USING GTS (SWING GRILLE ACTUATOR ASSEMBLY OPERATION)
10.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

f.

Turn the power switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

11.PERFORM UTILITY USING GTS (GRILL SHUTTER CONTROL MODE SWITCHING)
11.PERFORM UTILITY USING GTS (GRILL SHUTTER CONTROL MODE SWITCHING)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Grill Shutter / Utility / Grill Shutter Control Mode Switching.

Body Electrical > Grill Shutter > Utility
Tester Display
Grill Shutter Control Mode Switching
50005 352 4221

e.

According to the display on the GTS, change the grille shutter control mode from maintenance mode to normal mode.


f.

Check for DTCs and make sure that DTC B1333 is not output.

Body Electrical > Grill Shutter > Trouble Codes
50001 352

Result:
Proceed to
NEXT



NEXT

END