Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM33C0E _59 Vehicle Exterior _065471 WIPER / WASHER _0332906 WIPER AND WASHER SYSTEM C

WIPER / WASHER  WIPER AND WASHER SYSTEM  B1372  Wiper Switch Signal Mismatch between LIN and Line  


DESCRIPTION

Under normal operation, the windshield wiper motor assembly receives operation signals from the windshield wiper switch assembly via LIN communication.

The windshield wiper motor assembly and windshield wiper switch assembly are also connected via direct line in order to operate the front wipers in HI in an emergency. If the operation signals sent via LIN communication and direct line do not match, this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from
B1372 Wiper Switch Signal Mismatch between LIN and Line
Detection condition:

Auxiliary battery voltage is 9.5 V or more


Malfunction Status:

The operation signals sent via LIN communication and direct line do not match


Malfunction Time:

10 seconds or more


·

Windshield wiper motor assembly

·

Main body ECU (multiplex network body ECU)

·

Steering sensor

·

Harness or connector


○ Wiper

WIRING DIAGRAM

for LHD


E367354E04
5.094,2.042 7.156,2.313 2.063,0.271 10 false Front Wiper Switch 2.458,2.052 4.99,2.313 2.531,0.26 10 false Steering Wheel Switch Housing 0.708,7.292 3.24,7.552 2.531,0.26 10 false Steering Sensor 4.823,7.458 6.458,7.854 1.635,0.396 10 false Main Body ECU (Multiplex Network Body ECU) 4.635,5.01 6.781,5.333 2.146,0.323 10 false Windshield Wiper Motor Assembly 4.604,4.333 5.063,4.531 0.458,0.198 10 false LIN 4.594,6.271 5.052,6.469 0.458,0.198 10 false LIN3 4.604,3.802 5.063,4 0.458,0.198 10 false 2S 2.031,3.677 2.49,3.875 0.458,0.198 10 false 2S 2.104,1.583 2.563,1.781 0.458,0.198 10 false E 2.021,1.167 2.479,1.365 0.458,0.198 10 false +2 1.417,0.302 1.875,0.5 0.458,0.198 10 false 5 V 0.375,3.74 0.833,3.938 0.458,0.198 10 false IC 0.854,7.979 3.385,8.24 2.531,0.26 10 false : CAN Communication Line 0.854,8.417 3.385,8.677 2.531,0.26 10 false : LIN Communication Line 2.313,3.792 2.771,3.99 0.458,0.198 10 false K71 4.333,1.698 4.792,1.896 0.458,0.198 10 false z7 4.323,1.281 4.781,1.479 0.458,0.198 10 false z7 2.344,1.271 2.802,1.469 0.458,0.198 10 false z6 2.344,1.677 2.802,1.875 0.458,0.198 10 false z6 4.313,1.104 4.771,1.302 0.458,0.198 10 false 12 2.354,1.094 2.813,1.292 0.458,0.198 10 false 27 2.354,1.51 2.813,1.708 0.458,0.198 10 false 33 4.354,1.51 4.813,1.708 0.458,0.198 10 false 5 2.385,3.604 2.844,3.802 0.458,0.198 10 false 2 4.417,3.677 4.875,3.875 0.458,0.198 10 false 3 4.417,4.177 4.875,4.375 0.458,0.198 10 false 2 4.656,4.844 5.115,5.042 0.458,0.198 10 false A31 4.833,7.292 5.292,7.49 0.458,0.198 10 false K51 4.427,6.115 4.885,6.313 0.458,0.198 10 false 3 5.958,1.708 6.115,1.906 0.156,0.198 10 false E 5.917,1.292 6.115,1.5 0.198,0.208 10 false +2 5.25,0.896 5.448,1.104 0.198,0.208 10 false HI 4.583,2.594 7.115,2.854 2.531,0.26 10 false Windshield Wiper Switch Assembly


for RHD


E367354E05
5.094,2.042 7.156,2.313 2.063,0.271 10 false Front Wiper Switch 2.458,2.052 4.99,2.313 2.531,0.26 10 false Steering Wheel Switch Housing 0.708,7.292 3.24,7.552 2.531,0.26 10 false Steering Sensor 4.823,7.458 6.458,7.854 1.635,0.396 10 false Main Body ECU (Multiplex Network Body ECU) 4.635,5.01 6.781,5.333 2.146,0.323 10 false Windshield Wiper Motor Assembly 4.604,4.333 5.063,4.531 0.458,0.198 10 false LIN 4.594,6.271 5.052,6.469 0.458,0.198 10 false LIN3 4.604,3.802 5.063,4 0.458,0.198 10 false 2S 2.031,3.677 2.49,3.875 0.458,0.198 10 false 2S 2.104,1.583 2.563,1.781 0.458,0.198 10 false E 2.021,1.167 2.479,1.365 0.458,0.198 10 false +2 1.417,0.302 1.875,0.5 0.458,0.198 10 false 5 V 0.375,3.74 0.833,3.938 0.458,0.198 10 false IC 0.854,7.979 3.385,8.24 2.531,0.26 10 false : CAN Communication Line 0.854,8.417 3.385,8.677 2.531,0.26 10 false : LIN Communication Line 2.313,3.792 2.771,3.99 0.458,0.198 10 false K71 4.333,1.698 4.792,1.896 0.458,0.198 10 false z7 4.323,1.281 4.781,1.479 0.458,0.198 10 false z7 2.344,1.271 2.802,1.469 0.458,0.198 10 false z6 2.344,1.677 2.802,1.875 0.458,0.198 10 false z6 4.313,1.104 4.771,1.302 0.458,0.198 10 false 13 2.354,1.094 2.813,1.292 0.458,0.198 10 false 27 2.354,1.51 2.813,1.708 0.458,0.198 10 false 33 4.354,1.51 4.813,1.708 0.458,0.198 10 false 4 2.385,3.604 2.844,3.802 0.458,0.198 10 false 2 4.427,3.677 4.885,3.875 0.458,0.198 10 false 2 4.417,4.167 4.875,4.365 0.458,0.198 10 false 3 4.656,4.844 5.115,5.042 0.458,0.198 10 false A31 4.833,7.292 5.292,7.49 0.458,0.198 10 false K51 4.427,6.115 4.885,6.313 0.458,0.198 10 false 3 5.958,1.708 6.115,1.906 0.156,0.198 10 false E 5.917,1.292 6.115,1.5 0.198,0.208 10 false +2 5.25,0.896 5.448,1.104 0.198,0.208 10 false HI 4.583,2.594 7.115,2.854 2.531,0.26 10 false Windshield Wiper Switch Assembly


CAUTION / NOTICE / HINT

NOTICE:

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.


PROCEDURE

1.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Wiper / Trouble Codes.


e.

Clear the DTCs.

Body Electrical > Wiper > Clear DTCs
50002 384

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Wait 10 seconds or more.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Wiper / Trouble Codes.


f.

Check for DTCs.

Body Electrical > Wiper > Trouble Codes
50001 384

Result:
Result Proceed to
DTC B1372 is not output A
DTC B1372 is output B



A

B

3.READ VALUE USING GTS
3.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Wiper / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Wiper > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Wiper Switch HI (Line) Front wiper switch HI position signal (direct line) OFF or ON OFF: Front wiper switch not in HI position
ON: Front wiper switch in HI position
-
Body Electrical > Wiper > Data List
Tester Display
Wiper Switch HI (Line)
50003 384 20
OK:

The GTS display is normal.



Result:
Result
OK
NG



OK

4.READ VALUE USING GTS

NG

7.CHECK HARNESS AND CONNECTOR (STEERING SENSOR - WINDSHIELD WIPER MOTOR ASSEMBLY)
4.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / Steering Angle Sensor / Data List.


e.

Read the Data List according to the display on the GTS.

Chassis > Steering Angle Sensor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Wiper Hi Switch Front wiper switch HI position signal OFF or ON OFF: Front wiper switch not in HI position
ON: Front wiper switch in HI position
-
Chassis > Steering Angle Sensor > Data List
Tester Display
Wiper Hi Switch
50003 417 16
OK:

The GTS display is normal.



Result:
Result
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - WINDSHIELD WIPER MOTOR ASSEMBLY)

NG

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - WINDSHIELD WIPER MOTOR ASSEMBLY)
a.

Disconnect the K51 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the A31 windshield wiper motor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
K51-3 (LIN3) - A31-2 (LIN) Always Below 1 Ω
K51-3 (LIN3) or A31-2 (LIN) - Body ground Always 10 kΩ Higher

for RHD
Tester Connection Condition Specified Condition
K51-3 (LIN3) - A31-3 (LIN) Always Below 1 Ω
K51-3 (LIN3) or A31-3 (LIN) - Body ground Always 10 kΩ Higher



Result:
Proceed to
OK
NG



OK

6.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
E366392C01
1.5,0.25 1.917,0.5 0.417,0.25 0.76,1.646 1.167,0.917 false 1.594,0.292 2,0.531 0.406,0.24 10 false K51 0.604,1.719 0.938,1.917 0.333,0.198 10 false LIN3 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a
*a Component without harness connected
(Main Body ECU (Multiplex Network Body ECU)


a.

Check for voltage and pulses according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K51-3 (LIN3) - Body ground Power switch off Below 1 V
Power switch on (IG) Pulse generation



Result:
Proceed to
OK
NG



OK

REPLACE WINDSHIELD WIPER MOTOR ASSEMBLY

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

7.CHECK HARNESS AND CONNECTOR (STEERING SENSOR - WINDSHIELD WIPER MOTOR ASSEMBLY)
a.

Disconnect the K71 steering sensor connector.


b.

Disconnect the A31 windshield wiper motor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
K71-2 (2S) - A31-3 (2S) Always Below 1 Ω
K71-2 (2S) or A31-3 (2S) - Body ground Always 10 kΩ Higher

for RHD
Tester Connection Condition Specified Condition
K71-2 (2S) - A31-2 (2S) Always Below 1 Ω
K71-2 (2S) or A31-2 (2S) - Body ground Always 10 kΩ Higher



Result:
Proceed to
OK
NG



OK

8.INSPECT STEERING SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT STEERING SENSOR
E367361C02
1.271,0.646 1.625,0.896 0.354,0.25 4.677,0.771 5.031,1.021 0.354,0.25 1.844,2.146 1.635,1.552 false 5.354,1.958 5.156,1.635 false 0.281,0.292 0.594,0.49 0.313,0.198 10 false *a 1.313,0.677 1.625,0.875 0.313,0.198 10 false K71 4.792,0.813 5.104,1.01 0.313,0.198 10 false z6 1.781,2.188 2.281,2.427 0.5,0.24 10 false 2S 5.313,1.979 5.563,2.208 0.25,0.229 10 false +2
*a Component without harness connected
(Steering Sensor)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K71-2 (2S) - z6-27 (+2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE WINDSHIELD WIPER MOTOR ASSEMBLY

NG