Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › 2017.09–2017.12
RM33C0E _59 Vehicle Exterior _065471 WIPER / WASHER _0332906 WIPER AND WASHER SYSTEM C

WIPER / WASHER  WIPER AND WASHER SYSTEM  B1373  Lost Communication with Wiper System LIN BUS  


DESCRIPTION

The main body ECU (multiplex network body ECU) and windshield wiper motor assembly communicate via LIN communication. The main body ECU (multiplex network body ECU) stores this DTC if communication becomes abnormal.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from
B1373 Lost Communication with Wiper System LIN BUS
Detection condition:

Auxiliary battery voltage is 9.5 V or more


Malfunction Status:

A malfunction in the communication or LIN communication line between the main body ECU (multiplex network body ECU) and components of the wiper system occurs


Malfunction Time:

7 seconds or more 3 times consecutively


·

Windshield wiper motor assembly

·

Main body ECU (multiplex network body ECU)

·

Harness or connector

·

Rain sensor


○ Main body ECU (multiplex network body ECU)

WIRING DIAGRAM

E378085E02
0.083,1.156 1.771,1.354 1.688,0.198 10 false K51 0.073,1.323 3.25,1.688 3.177,0.365 10 false Main Body ECU (Multiplex Network Body ECU) 0.813,3.302 2.5,3.5 1.688,0.198 10 false : LIN Communication Line 2.219,0.615 3.906,0.813 1.688,0.198 10 false LIN3 2.615,0.448 2.896,0.656 0.281,0.208 10 false 3 4.625,0.615 6.313,0.813 1.688,0.198 10 false LIN 4.74,1.156 6.427,1.354 1.688,0.198 10 false A31 4.74,1.313 7.104,1.615 2.365,0.302 10 false Windshield Wiper Motor Assembly 4.625,2.583 6.313,2.781 1.688,0.198 10 false MPX 5.323,3.313 6.635,3.563 1.313,0.25 10 false Rain Sensor 4,0.448 4.729,0.656 0.729,0.208 10 false 2*1, 3*2 4.438,2.438 4.719,2.646 0.281,0.208 10 false 3 5.313,3.135 6.219,3.469 0.906,0.333 10 false V4*1, V5*2 0.635,2.24 2.323,2.438 1.688,0.198 10 false *1: for LHD 0.635,2.615 2.323,2.813 1.688,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.


PROCEDURE

1.CHECK RAIN SENSOR
a.

Disconnect the V4*1 or V5*2 rain sensor connector.

*1: for LHD

*2: for RHD



b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

c.

Turn the power switch on (IG) and wait for at least 10 seconds.


d.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
Only DTC B1279 is output A
DTC B1373 is output B



A

B

2.CHECK WINDSHIELD WIPER MOTOR ASSEMBLY
2.CHECK WINDSHIELD WIPER MOTOR ASSEMBLY
a.

Disconnect the A31 windshield wiper motor assembly connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

c.

Turn the power switch on (IG) and wait for at least 10 seconds.


d.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
Only DTC B1245 is output A
DTC B1373 is output B



A

REPLACE WINDSHIELD WIPER MOTOR ASSEMBLY

B

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - WINDSHIELD WIPER MOTOR ASSEMBLY AND RAIN SENSOR)
3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - WINDSHIELD WIPER MOTOR ASSEMBLY AND RAIN SENSOR)
a.

Disconnect the K51 main body ECU (multiplex network body ECU) connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

c.

Turn the power switch on (IG) and wait for at least 10 seconds.


d.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B1373 is not output A
DTC B1373 is output B



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)