The main body ECU (multiplex network body ECU) and rain sensor communicate via LIN communication. The main body ECU (multiplex network body ECU) stores this DTC if communication becomes abnormal.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | DTC Output from |
|---|---|---|---|---|---|
| B1279 | Lost Communication with Humidity/Rain Sensor LIN | Detection Condition:
Auxiliary battery voltage is 9.5 V or more Malfunction Status:
Communication malfunction with rain sensor Malfunction Duration:
10 seconds or more |
·
Rain sensor ·
Harness or connector ·
Main body ECU (multiplex network body ECU) |
○ | Main Body |
Inspect the fuses of circuits related to this system before performing the following procedure.
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| Only DTC B1279 is output | A |
| DTC B1279 and B1373 are output | B |
A
B
Disconnect the K51 main body ECU (multiplex network body ECU) connector.
Disconnect the V4*1 or V5*2 rain sensor connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K51-3 (LIN3) - V4-3 (MPX) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K51-3 (LIN3) - V5-3 (MPX) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Main Body ECU (Multiplex Network Body ECU) |
Check for voltage and pulses according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K51-3 (LIN3) - Body ground | Power switch off | Below 1 V |
| Power switch on (IG) | Pulse generation |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | for LHD |
| *B | for RHD |
| *a | Front view of wire harness connector
(to Rain Sensor) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V4-4 (SIG) - Body ground | Power switch off | Below 1 V |
| Power switch on (IG) | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V5-4 (SIG) - Body ground | Power switch off | Below 1 V |
| Power switch on (IG) | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | for LHD |
| *B | for RHD |
| *a | Front view of wire harness connector
(to Rain Sensor) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V4-2 (ES) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V5-2 (ES) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG