This DTC is stored when a power seat motor operates (a position control sensor is being supplied with power) and the power supply voltage does not rise to the specified value.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2658 | Short in Sensor with Motor Power Supply Circuit | Slide motor position sensor power supply voltage is low | ·
Position control ECU assembly (driver seat) ·
Slide motor (Upper seat track rail sub-assembly (driver seat)) ·
Power Seat Tilt Motor Assembly (Driver Seat) ·
Power Seat Lifter Motor Assembly (Driver Seat) ·
Reclining Motor (Front Seatback Frame Sub-assembly (Driver Seat)) ·
Wire harness or connector |
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
DTC B2658 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Disconnect the a31 position control ECU assembly (driver seat) connector.
Disconnect the a28 slide motor (front seat adjuster assembly (driver seat)) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a31-26 (SSRS) - a28-2 | Always | Below 1 Ω |
| a31-26 (SSRS) or a28-2 - Body ground | Always | 10 kΩ or higher |
| a31-12 (SENG) - a28-3 | Always | Below 1 Ω |
| a31-12 (SENG) or a28-3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the a28 slide motor (front seat adjuster assembly (driver seat)) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a28-2 - a28-3 | Slide switch on | 4.8 to 5.1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the a31 position control ECU assembly (driver seat) connector.
Disconnect the a33 power seat tilt motor assembly (driver seat) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a31-10 (SSFV) - a33-2 | Always | Below 1 Ω |
| a31-10 (SSFV) or a33-2 - Body ground | Always | 10 kΩ or higher |
| a31-12 (SENG) - a33-3 | Always | Below 1 Ω |
| a31-12 (SENG) or a33-3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the a33 power seat tilt motor assembly (driver seat) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a33-2 - a33-3 | Front vertical switch on | 4.8 to 5.1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the a31 position control ECU assembly (driver seat) connector.
Disconnect the a36 power seat lifter motor assembly (driver seat) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a31-25 (SSRL) - a36-2 | Always | Below 1 Ω |
| a31-25 (SSRL) or a36-2 - Body ground | Always | 10 kΩ or higher |
| a31-12 (SENG) - a36-3 | Always | Below 1 Ω |
| a31-12 (SENG) or a36-3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the a36 power seat lifter motor assembly (driver seat) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a36-2 - a36-3 | Lifter switch on | 4.8 to 5.1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the a31 position control ECU assembly (driver seat) connector.
Disconnect the q1 reclining motor (front seatback frame sub-assembly (driver seat)) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a31-11 (SSRR) - q1-2 | Always | Below 1 Ω |
| a31-11 (SSRR) or q1-2 - Body ground | Always | 10 kΩ or higher |
| a31-12 (SENG) - q1-3 | Always | Below 1 Ω |
| a31-12 (SENG) or q1-3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the q1 reclining motor (front seatback frame sub-assembly (driver seat)) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| q1-2 - q1-3 | Reclining switch on | 4.8 to 5.1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the power seat tilt motor assembly (driver seat) with a new or known good one.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Recheck for DTCs.
DTC B2685 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the power seat lifter motor assembly (driver seat) with a new or known good one.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Recheck for DTCs.
DTC B2685 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the slide motor (upper seat track rail sub-assembly (driver seat)) with a new or known good one.
Click hereVehicle Interior>SEAT>POWER SEAT TRACK RAIL ASSEMBLY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Recheck for DTCs.
DTC B2685 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the reclining motor (front seatback frame sub-assembly (driver seat)) with a new or known good one.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Recheck for DTCs.
DTC B2685 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG