Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>PRECAUTION
When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
A communication malfunction DTC may be stored.
The radio and display receiver assembly may not operate normally.
Check the radio automatic station search function.
Check the radio automatic station search function by activating it.
| Result | Proceed to |
|---|---|
| Automatic station search function does not stop. | A |
| Automatic station search function stops on a station. | B |
A
B
Check if any optional components that may decrease reception capacity, such as a sunshade film or telephone antenna, are installed.
| Result | Proceed to |
|---|---|
| Optional components are not installed. | A |
| Optional components are installed. | B |
Do not remove optional components without the permission of the customer.
A
B
Preparation for check
Disconnect the antenna connector from the radio and display receiver assembly.
Check for noise
Turn the power switch on (ACC) with the radio and display receiver assembly connector connected.
Turn the radio on and tune into AM mode.
Place a screwdriver, thin wire or other metal object on the radio and display receiver assembly antenna jack and check that noise can be heard from the speakers.
Noise can be heard from the speakers.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Tester Probe |
| *b | Antenna Wire |
| *c | Tin Foil |
Check for continuity in the window glass antenna wire.
When cleaning the glass, wipe it in the direction of the wire with a soft dry cloth. Take care not to damage the wire. Do not use detergents or glass cleaners with abrasive ingredients. When measuring resistance, wrap a piece of tin foil around the tip of each probe and press the foil against the wire with your finger, as shown in the illustration.
Check for continuity at the center of each antenna wire as shown in the illustration.
There is continuity in the window glass antenna wire.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the RA radio and display receiver assembly connector.
| *a | Component without harness connected
(Radio and Display Receiver Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| RA-5 (ANT+) - Body ground | Power switch on (ACC)
Radio switch on and FM or AM selected |
11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the antenna cord sub-assembly (for front side) with a new or known good one and check if radio broadcasts can be received normally.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL
Radio broadcasts can be received normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the No. 2 antenna cord sub-assembly with a new or known good one and check if radio broadcasts can be received normally.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL
Radio broadcasts can be received normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the No. 1 amplifier antenna assembly with a new or known good one and check if radio broadcasts can be received normally.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA>REMOVAL
Radio broadcasts can be received normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the antenna cord sub-assembly (for rear side) with a new or known good one and check if radio broadcasts can be received normally.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA>REMOVAL
Radio broadcasts can be received normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG