Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2017.09–2019.02
RM33C0E _56 Audio / Visual / Telematics _065450 AUDIO / VIDEO _0333622 AUDIO AND VISUAL SYSTEM C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  B1579  Voice Recognition Microphone Disconnected  


DESCRIPTION

The radio and display receiver assembly, roof console box sub-assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.

This DTC is stored when a microphone connection detection signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1579 Voice Recognition Microphone Disconnected Microphone signal is lost
·

Roof console box sub-assembly

·

Telephone microphone assembly

·

Radio and display receiver assembly

·

Harness or connector



WIRING DIAGRAM

w/o Sliding Roof


E371450E07
5.25,2.135 6.927,2.542 1.677,0.406 10 false Radio and Display Receiver Assembly 5.094,1.969 5.625,2.323 0.531,0.354 10 false K2 3.042,2 4.167,2.458 1.125,0.458 10 false Roof Console Box Sub-assembly 0.417,2.073 2.583,2.385 2.167,0.313 10 false Telephone Microphone Assembly 2.927,1.135 3.333,1.448 0.406,0.313 10 false B 2.917,0.719 3.323,1.031 0.406,0.313 10 false B 4.083,1.135 4.49,1.448 0.406,0.313 10 false V12 4.083,0.719 4.49,1.031 0.406,0.313 10 false V12 4.146,0.531 4.552,0.844 0.406,0.313 10 false 12 4.125,0.948 4.531,1.26 0.406,0.313 10 false 11 2.927,0.521 3.333,0.833 0.406,0.313 10 false 1 2.948,0.948 3.354,1.26 0.406,0.313 10 false 2 5.073,0.604 5.479,0.917 0.406,0.313 10 false 25 5.063,1.042 5.469,1.354 0.406,0.313 10 false 22 5.271,0.729 5.729,1 0.458,0.271 10 false SNS2 5.281,1.156 5.74,1.427 0.458,0.271 10 false MIN- 3.625,0.708 4.083,0.979 0.458,0.271 10 false SNS2 3.604,1.115 4.063,1.385 0.458,0.271 10 false MCO- 3.677,1.531 4.135,1.802 0.458,0.271 10 false GND 4.083,1.542 4.49,1.854 0.406,0.313 10 false V12 4.156,1.365 4.563,1.677 0.406,0.313 10 false 4


w/ Sliding Roof


E371450E03
5.25,2.135 6.927,2.542 1.677,0.406 10 false Radio and Display Receiver Assembly 5.094,1.969 5.625,2.323 0.531,0.354 10 false K2 3.042,2 4.167,2.458 1.125,0.458 10 false Roof Console Box Sub-assembly 0.531,2.052 2.698,2.365 2.167,0.313 10 false Telephone Microphone Assembly 2.927,1.135 3.333,1.448 0.406,0.313 10 false B 2.906,0.719 3.313,1.031 0.406,0.313 10 false B 4.083,1.135 4.49,1.448 0.406,0.313 10 false V14 4.083,0.719 4.49,1.031 0.406,0.313 10 false V14 4.146,0.531 4.552,0.844 0.406,0.313 10 false 6 4.125,0.948 4.531,1.26 0.406,0.313 10 false 7 2.927,0.521 3.333,0.833 0.406,0.313 10 false 1 2.948,0.948 3.354,1.26 0.406,0.313 10 false 2 5.073,0.604 5.479,0.917 0.406,0.313 10 false 25 5.063,1.042 5.469,1.354 0.406,0.313 10 false 22 5.271,0.729 5.729,1 0.458,0.271 10 false SNS2 5.281,1.156 5.74,1.427 0.458,0.271 10 false MIN- 3.604,0.698 4.063,0.969 0.458,0.271 10 false SNS2 3.604,1.115 4.063,1.385 0.458,0.271 10 false MCO- 3.667,1.521 4.125,1.792 0.458,0.271 10 false GND 4.073,1.542 4.479,1.854 0.406,0.313 10 false V14 4.156,1.365 4.563,1.677 0.406,0.313 10 false 15


CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>PRECAUTION

·

When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:

-

A communication malfunction DTC may be stored.

-

The radio and display receiver assembly may not operate normally.




PROCEDURE

1.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
E360498C04
1.531,0.729 1.896,1.01 0.365,0.281 2.813,2.604 2.052,2.156 false 0.25,0.24 0.563,0.438 0.313,0.198 10 false *a 1.635,0.792 1.948,0.99 0.313,0.198 10 false K2 2.865,2.563 3.24,2.771 0.375,0.208 10 false MIN-
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K2-22 (MIN-) - Body ground Always Below 1 Ω


Result:
Result Proceed to
OK (w/ Sliding Roof) A
OK (w/o Sliding Roof) B
NG C




A

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX SUB-ASSEMBLY)

B

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX SUB-ASSEMBLY)

C

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX SUB-ASSEMBLY)
a.

Disconnect the K2 radio and display receiver assembly connector.


b.

Disconnect the V14 roof console box sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K2-25 (SNS2) - V14-6 (SNS2) Always Below 1 Ω
K2-22 (MIN-) - V14-7 (MCO-) Always Below 1 Ω
K2-25 (SNS2) or V14-6 (SNS2) - Body ground Always 10 kΩ or higher
K2-22 (MIN-) or V14-7 (MCO-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
a.

Remove the roof console box sub-assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.
E360501C01
1.76,1.24 1.688,0.698 false 1.969,1.24 2.208,0.719 false 0.156,0.146 0.469,0.344 0.313,0.198 10 false *a 1.521,0.531 1.948,0.74 0.427,0.208 10 false MCO- 2.104,0.552 2.531,0.771 0.427,0.219 10 false SNS2
*a Component without harness connected
(Roof Console Box Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (SNS2) - 7 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

4.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
4.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
a.

Remove the roof console box sub-assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Disconnect the B telephone microphone assembly connector.


c.
E371472C09
1.427,2.781 1.885,3.042 0.458,0.26 1.563,0.427 2.021,0.688 0.458,0.26 1.823,1.583 1.563,0.875 false 1.969,1.583 2.229,0.885 false 2.448,2.448 2.708,1.75 false 1.167,0.781 1.677,1.052 0.51,0.271 10 false MCO- 0.188,0.24 0.5,0.438 0.313,0.198 10 false *a 0.219,2.708 0.531,2.906 0.313,0.198 10 false *b 1.646,0.479 2.125,0.698 0.479,0.219 10 false V14 1.625,2.844 2.104,3.063 0.479,0.219 10 false B 2.302,0.781 2.844,1 0.542,0.219 10 false SNS2 2.135,2.396 2.677,2.615 0.542,0.219 10 false GND
*a Component without harness connected
(Roof Console Box Sub-assembly (No. 1 Roof Wire Side))
*b Component without harness connected
(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-1 - V14-6 (SNS2) Always Below 1 Ω
B-2 - V14-7 (MCO-) Always Below 1 Ω
B-1 or V14-6 (SNS2) - V14-15 (GND) Always 10 kΩ or higher
B-2 or V14-7 (MCO-) - V14-15 (GND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE ROOF CONSOLE BOX SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX SUB-ASSEMBLY)
a.

Disconnect the K2 radio and display receiver assembly connector.


b.

Disconnect the V12 roof console box sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K2-25 (SNS2) - V12-12 (SNS2) Always Below 1 Ω
K2-22 (MIN-) - V12-11 (MCO-) Always Below 1 Ω
K2-25 (SNS2) or V12-12 (SNS2) - Body ground Always 10 kΩ or higher
K2-22 (MIN-) or V12-11 (MCO-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
a.

Remove the roof console box sub-assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.
E360499C01
1.74,1.698 1.573,1.385 false 1.219,1.719 1.458,1.385 false 0.25,0.156 0.563,0.354 0.313,0.198 10 false *a 1.031,1.719 1.479,1.958 0.448,0.24 10 false SNS2 1.667,1.698 2.156,1.958 0.49,0.26 10 false MCO-
*a Component without harness connected
(Roof Console Box Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
12 (SNS2) - 11 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

7.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
7.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
a.

Remove the roof console box sub-assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Disconnect the B telephone microphone assembly connector.


c.
E371473C13
1.458,2.75 1.885,3.01 0.427,0.26 1.417,0.563 1.844,0.823 0.427,0.26 1.042,1.531 0.771,0.969 false 1.396,2.073 1.51,1.729 false 1.865,2.177 1.625,1.74 false 0.26,0.292 0.573,0.49 0.313,0.198 10 false *a 0.281,2.74 0.594,2.938 0.313,0.198 10 false *b 1.052,2.083 1.563,2.365 0.51,0.281 10 false SNS2 1.917,2.094 2.427,2.375 0.51,0.281 10 false MCO- 0.448,0.875 0.958,1.156 0.51,0.281 10 false GND 1.5,0.625 2.01,0.906 0.51,0.281 10 false V12 1.625,2.813 2.135,3.094 0.51,0.281 10 false B
*a Component without harness connected
(Roof Console Box Sub-assembly (No. 1 Roof Wire Side))
*b Component without harness connected
(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-1 - V12-12 (SNS2) Always Below 1 Ω
B-2 - V12-11 (MCO-) Always Below 1 Ω
B-1 or V12-12 (SNS2) - V12-4 (GND) Always 10 kΩ or higher
B-2 or V12-11 (MCO-) - V12-4 (GND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE ROOF CONSOLE BOX SUB-ASSEMBLY