Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM
RM33C0E _56 Audio / Visual / Telematics _065450 AUDIO / VIDEO _0333622 AUDIO AND VISUAL SYSTEM C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  B15D3  Stereo Component Amplifier Disconnected  


DESCRIPTION

The radio and display receiver assembly and stereo component amplifier assembly are connected via AVC-LAN communication line.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15D3 Stereo Component Amplifier Disconnected When either of the following conditions is met:
·

Stereo component amplifier assembly is/was not connected while the power switch is/was on (IG) or (ACC)

·

Communication between the master unit and the stereo component amplifier assembly is not possible when the hybrid system is operated.


·

Stereo component amplifier assembly power source circuit

·

AVC-LAN circuit between radio and display receiver assembly and stereo component amplifier assembly

·

Stereo component amplifier assembly

·

Radio and display receiver assembly

·

Harness or connector



HINT:

The radio and display receiver assembly is the master unit.


WIRING DIAGRAM

E371990E16
5.229,0.552 5.708,0.76 0.479,0.208 10 false K14 5.219,1.365 5.698,1.573 0.479,0.208 10 false K9 5.615,0.531 6.094,0.74 0.479,0.208 10 false +B 3.771,0.667 4.604,0.885 0.833,0.219 10 false AMP NO. 1 1.323,0.521 2.906,0.802 1.583,0.281 10 false from Auxiliary Battery 1.625,1.333 2.865,1.531 1.24,0.198 10 false from ACC Relay 2.354,2.688 2.833,2.896 0.479,0.208 10 false K3 2.344,2.833 4.042,3.26 1.698,0.427 10 false Radio and Display Receiver Assembly 1.104,4.188 3.396,4.469 2.292,0.281 10 false : AVC-LAN Communication Line 5.427,3.646 6.615,4.063 1.188,0.417 10 false Stereo Component Amplifier Assembly 5.25,3.021 5.729,3.229 0.479,0.208 10 false 18 5.302,2.656 5.781,2.865 0.479,0.208 10 false 3 5.313,2.146 5.792,2.354 0.479,0.208 10 false 7 5.292,1.646 5.771,1.854 0.479,0.208 10 false 8 5.26,1.167 5.74,1.375 0.479,0.208 10 false 12 5.26,0.74 5.74,0.948 0.479,0.208 10 false 16 5.292,0.333 5.771,0.542 0.479,0.208 10 false 1 5.615,1.844 6.094,2.052 0.479,0.208 10 false TX+ 5.615,1.365 6.094,1.573 0.479,0.208 10 false ACC 5.615,2.823 6.094,3.031 0.479,0.208 10 false GND 3.615,2.219 4.094,2.427 0.479,0.208 10 false 6 3.615,1.729 4.094,1.938 0.479,0.208 10 false 5 3.802,1.51 4.573,1.75 0.771,0.24 10 false ECU-ACC 5.604,0.938 6.083,1.146 0.479,0.208 10 false +B2 5.615,2.333 6.094,2.542 0.479,0.208 10 false TX- 5.604,3.208 6.083,3.417 0.479,0.208 10 false GND2 3.229,1.844 3.708,2.052 0.479,0.208 10 false TX1+ 3.26,2.344 3.74,2.552 0.479,0.208 10 false TX1- 3.74,1.104 4.573,1.323 0.833,0.219 10 false AMP NO. 2 5.25,0.958 5.729,1.167 0.479,0.208 10 false K14 5.229,2.844 5.708,3.052 0.479,0.208 10 false K14 5.24,3.229 5.719,3.438 0.479,0.208 10 false K14 5.229,1.854 5.708,2.063 0.479,0.208 10 false K9 5.24,2.344 5.719,2.552 0.479,0.208 10 false K9 1.323,0.927 2.906,1.208 1.583,0.281 10 false from Auxiliary Battery

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>PRECAUTION

·

When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:

-

A communication malfunction DTC may be stored.

-

The radio and display receiver assembly may not operate normally.


·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK DTC
a.

If DTC B15C3 is output, perform troubleshooting for DTC B15C3 first.

Result:
Result Proceed to
DTC B15C3 is not output. A
DTC B15C3 is output. B




A

2.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

2.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Check that optional components (including associated wiring) which generate radio waves are not installed.

Result:
Result Proceed to
Optional components (including associated wiring) are installed. A
Optional components (including associated wiring) are not installed. B


HINT:
·

Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

·

This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.





A

3.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

4.CHECK DTC
3.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Remove optional components (including associated wiring).

NOTICE:

Do not remove optional components or associated wiring without the permission of the customer.



Result:
Proceed to
NEXT



NEXT

4.CHECK DTC
4.CHECK DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY POWER SOURCE)
5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY POWER SOURCE)
a.

Disconnect the K14 and K9 stereo component amplifier assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K14-3 (GND) - Body ground Always Below 1 Ω
K14-18 (GND2) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K14-1 (+B) - K14-3 (GND) Power switch off 11 to 14 V
K14-16 (+B2) - K14-3 (GND) Power switch off 11 to 14 V
K9-12 (ACC) - K14-3 (GND) Power switch on (ACC) 11 to 14 V


Result:
Proceed to
OK
NG




OK

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the K3 radio and display receiver assembly connector.


b.

Disconnect the K9 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K3-5 (TX1+) - K9-8 (TX+) Always Below 1 Ω
K3-6 (TX1-) - K9-7 (TX-) Always Below 1 Ω
K3-5 (TX1+) or K9-8 (TX+) - Body ground Always 10 kΩ or higher
K3-6 (TX1-) or K9-7 (TX-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY
a.

Replace the stereo component amplifier assembly with a new or known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>STEREO COMPONENT AMPLIFIER>REMOVAL


b.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY