Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › PANORAMIC MOON ROOF SYSTEM
RM33C0E _59 Vehicle Exterior _065468 SLIDING ROOF / CONVERTIBLE _0333641 PANORAMIC MOON ROOF SYSTEM U

SLIDING ROOF / CONVERTIBLE  PANORAMIC MOON ROOF SYSTEM  TERMINALS OF ECU  


CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)


B417851N33
3.354,0.104 3.781,0.333 0.427,0.229 3.469,0.125 3.781,0.323 0.313,0.198 10 false o1

a.

Disconnect the o1 sliding roof ECU (sliding roof drive gear assembly) connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
o1-1 (+B) - o1-2 (E) L - W-B Auxiliary battery power supply Power switch off 11 to 14 V
o1-6 (IG) - o1-2 (E) V - W-B IG power supply Power switch off Below 1 V
o1-6 (IG) - o1-2 (E) V - W-B IG power supply Power switch on (IG) 11 to 14 V
o1-2 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the o1 sliding roof ECU (sliding roof drive gear assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
o1-10 (ROOF OPEN) - o1-2 (E) BE - W-B Sliding roof open switch input signal Power switch on (IG), sliding roof open switch on Below 1 V
o1-10 (ROOF OPEN) - o1-2 (E) BE - W-B Sliding roof open switch input signal Power switch on (IG), sliding roof open switch off 11 to 14 V
o1-8 (ROOF CLOSE) - o1-2 (E) W - W-B Sliding roof close switch input signal Power switch on (IG), sliding roof close switch on Below 1 V
o1-8 (ROOF CLOSE) - o1-2 (E) W - W-B Sliding roof close switch input signal Power switch on (IG), sliding roof close switch off 11 to 14 V
o1-4 (VENT) - o1-2 (E) P - W-B Sliding roof tilt switch input signal Power switch on (IG), sliding roof tilt switch on Below 1 V
o1-4 (VENT) - o1-2 (E) P - W-B Sliding roof tilt switch input signal Power switch on (IG), sliding roof tilt switch off 11 to 14 V
o1-9 (SHADE CLOSE) - o1-2 (E) R - W-B Roof sunshade close switch input signal Power switch on (IG), roof sunshade close switch on Below 1 V
o1-9 (SHADE CLOSE) - o1-2 (E) R - W-B Roof sunshade close switch input signal Power switch on (IG), roof sunshade close switch off 11 to 14 V
o1-5 (SHADE OPEN) - o1-2 (E) G - W-B Roof sunshade open switch input signal Power switch on (IG), roof sunshade open switch on Below 1 V
o1-5 (SHADE OPEN) - o1-2 (E) G - W-B Roof sunshade open switch input signal Power switch on (IG), roof sunshade open switch off 11 to 14 V



CHECK ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)


B417851N34
3.354,0.104 3.781,0.333 0.427,0.229 3.479,0.125 3.792,0.323 0.313,0.198 10 false o2

a.

Disconnect the o2 roof sunshade ECU (sliding roof drive gear assembly) connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
o2-1 (+B) - o2-2 (E) G - W-B Auxiliary battery power supply Power switch off 11 to 14 V
o2-6 (IG) - o2-2 (E) V - W-B IG power supply Power switch off Below 1 V
o2-6 (IG) - o2-2 (E) V - W-B IG power supply Power switch on (IG) 11 to 14 V
o2-2 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the o2 roof sunshade ECU (sliding roof drive gear assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
o2-10 (ROOF OPEN) - o2-2 (E) BE - W-B Sliding roof open switch input signal Power switch on (IG), sliding roof open switch on Below 1 V
o2-10 (ROOF OPEN) - o2-2 (E) BE - W-B Sliding roof open switch input signal Power switch on (IG), sliding roof open switch off 11 to 14 V
o2-8 (ROOF CLOSE) - o2-2 (E) W - W-B Sliding roof close switch input signal Power switch on (IG), sliding roof close switch on Below 1 V
o2-8 (ROOF CLOSE) - o2-2 (E) W - W-B Sliding roof close switch input signal Power switch on (IG), sliding roof close switch off 11 to 14 V
o2-4 (VENT) - o2-2 (E) P - W-B Sliding roof tilt switch input signal Power switch on (IG), sliding roof tilt switch on Below 1 V
o2-4 (VENT) - o2-2 (E) P - W-B Sliding roof tilt switch input signal Power switch on (IG), sliding roof tilt switch off 11 to 14 V
o2-9 (SHADE CLOSE) - o2-2 (E) R - W-B Roof sunshade close switch input signal Power switch on (IG), roof sunshade close switch on Below 1 V
o2-9 (SHADE CLOSE) - o2-2 (E) R - W-B Roof sunshade close switch input signal Power switch on (IG), roof sunshade close switch off 11 to 14 V
o2-5 (SHADE OPEN) - o2-2 (E) G - W-B Roof sunshade open switch input signal Power switch on (IG), roof sunshade open switch on Below 1 V
o2-5 (SHADE OPEN) - o2-2 (E) G - W-B Roof sunshade open switch input signal Power switch on (IG), roof sunshade open switch off 11 to 14 V



CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>TERMINALS OF ECU