Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK
RM33C0E _58 Vehicle Interior _065455 DOOR LOCK _0333669 REAR DOOR LOCK A

DOOR LOCK  REAR DOOR LOCK  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 69780B 1.INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY

a.
B469787C01
0,0 0,0 false
V113147

Install in this Direction


Install the rear door inside locking cable assembly as shown in the illustration.


Hide 69740D 2.INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

a.
B469788C01
0,0 0,0 false
V113147

Install in this Direction


Install the rear door lock remote control cable assembly as shown in the illustration.


Hide 69038A 3.INSTALL REAR DOOR LOCK COVER SUB-ASSEMBLY

a.
B469789C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 claws as shown in the illustration.


b.
B469790

Engage the 2 claws to install the rear door lock cover sub-assembly as shown in the illustration.


Hide 69060A 4.INSTALL REAR DOOR LOCK WITH MOTOR ASSEMBLY

NOTICE:
·

When reusing a removed rear door lock with motor assembly, replace the door lock wiring harness seal with a new one.

·

Do not allow grease or dust to adhere to the door lock wiring harness seal installation surface.

·

Reusing a door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water ingress. This may result in a malfunction of the rear door lock with motor assembly.



a.

Apply MP grease to the sliding parts of the rear door lock with motor assembly.


b.

When reusing the rear door lock with motor assembly:

i.

Install a new door lock wiring harness seal to the rear door lock with motor assembly.



c.
B469781C01
2.865,2.865 2.781,2.604 true 2.823,2.875 3.01,3.052 0.188,0.177 10 true *a
*a Release Plate
V113147

Install in this Direction


Connect the rear door lock with motor assembly to the release plate of the rear door outside handle frame sub-assembly, and set it to the rear door panel.

HINT:

Make sure that the release plate of the rear door outside handle frame sub-assembly is securely connected to the rear door lock with motor assembly.



d.

Using a T30 "TORX" socket wrench, install the rear door lock with motor assembly with the 3 screws.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 68104 5.INSTALL REAR DOOR GLASS SUB-ASSEMBLY

Hide 68124B 6.INSTALL REAR DOOR QUARTER WINDOW GLASS

Hide 67408F 7.INSTALL REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY

Hide 67872 8.CONNECT REAR DOOR WEATHERSTRIP

a.

Connect the rear door weatherstrip.


Hide 68152C 9.INSTALL REAR DOOR GLASS RUN

Hide 67858B 10.INSTALL REAR DOOR PANEL PROTECTOR

Hide 67848A 11.INSTALL REAR DOOR NO. 1 VENT SEAL

Hide 67842E 12.INSTALL REAR DOOR SERVICE HOLE COVER

Hide 67844A 13.INSTALL REAR DOOR NO. 2 SERVICE HOLE COVER

Hide 68174A 14.INSTALL REAR DOOR INNER GLASS WEATHERSTRIP

Hide 67604 15.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

Hide 74260 16.INSTALL REAR ARMREST ASSEMBLY

Hide 17.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL

Hide 74038B 18.INSTALL REAR DOOR ARMREST COVER SUB-ASSEMBLY

Hide 19.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 64718C 20.INSTALL LUGGAGE TRIM SERVICE HOLE COVER

Hide 21. INITIALIZE POWER WINDOW CONTROL SYSTEM