Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
1. REPAIR INSTRUCTION
75988C
2.INSTALL REAR DOOR OUTSIDE STRIPE
75978H
3.INSTALL REAR DOOR LOWER OUTSIDE STRIPE
75708
4.INSTALL REAR DOOR WINDOW FRAME MOULDING SUB-ASSEMBLY
67846A
5.INSTALL REAR DOOR FRONT OUTSIDE SEAL
Engage the guide to install the rear door front outside seal.
75762A
6.INSTALL REAR DOOR FRONT WINDOW FRAME MOULDING
75792
7.INSTALL DOOR WINDOW FRAME MOULDING CLIP
|
Install in this Direction |
Engage the 2 claws to install the door window frame moulding clip.
75740
8.INSTALL REAR DOOR BELT MOULDING ASSEMBLY
67888F
9.INSTALL REAR DOOR NO. 2 WEATHERSTRIP
Engage the 5 clips to install the rear door No. 2 weatherstrip.
67003C
10.INSTALL REAR DOOR PANEL CUSHION
Engage the 4 claws to install 2 new rear door panel cushions.
65923E
11.INSTALL CURTAIN HOOK (w/ Rear Door Sunshade)
Engage the 4 claws to install the 2 curtain hooks.
Engage the 2 pins as shown in the illustration.
69204A
12.INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
Apply MP grease to the sliding parts of the rear door outside handle frame sub-assembly.
| *A | Outside |
| *B | Inside |
Engage the claw as shown in the illustration.
Using a T30 "TORX" socket wrench, install the rear door outside handle frame sub-assembly with the screw.
69242G
13.INSTALL REAR DOOR REAR OUTSIDE HANDLE PAD
Engage the 3 guides and claw to install the rear door rear outside handle pad.
69241G
14.INSTALL REAR DOOR FRONT OUTSIDE HANDLE PAD
Engage the 3 claws to install the rear door front outside handle pad.
69227L
15.INSTALL REAR DOOR OUTSIDE HANDLE COVER
Engage the claw.
Using a T30 "TORX" socket wrench, install the rear door outside handle cover with the screw.
69240
16.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY
|
Install in this Direction |
Insert the front end of the rear door outside handle assembly into the rear door outside handle frame sub-assembly.
Insert the rear end of the rear door outside handle assembly into the rear door outside handle frame sub-assembly, then slide the rear door outside handle assembly toward the front of the vehicle to install it.
|
Engage in this Direction |
Move the lever as shown in the illustration and engage the 2 claws to secure the rear door outside handle assembly.
69060A
17.INSTALL REAR DOOR LOCK WITH MOTOR ASSEMBLY
18.INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY
Apply MP grease to the sliding parts of the rear door window regulator assembly.
Temporarily install the temporary bolt to the rear door window regulator assembly.
| *a | Temporary Bolt |
Temporarily install the rear door window regulator assembly with the 3 bolts.
Tighten the temporary bolt and 3 bolts to install the rear door window regulator assembly.
Tighten the bolts in the order shown in the illustration.
Connect the connector.
69975A
19.INSTALL REAR DOOR GLASS CHANNEL FILLER
Apply soapy water to a new rear door glass channel filler.
| *A | Front Side |
| *B | Rear Side |
| *a | Edge of curved surface |
Install the rear door glass channel filler to the rear door glass sub-assembly at position shown in the illustration.
| Area | Measurement |
|---|---|
| A | 5.0 mm (0.197 in.) |
| B | 5.0 mm (0.197 in.) |
69906B
20.INSTALL REAR DOOR GLASS CHANNEL SUB-ASSEMBLY
Apply soapy water to the channel filler side of the rear door glass channel sub-assembly.
| *A | Front Side |
| *B | Rear Side |
| *a | Edge of curved surface |
Using a plastic hammer, install the rear door glass channel sub-assembly to the position shown in the illustration.
| Area | Measurement |
|---|---|
| A | 5.0 mm (0.197 in.) |
| B | 5.0 mm (0.197 in.) |
To prevent damaging the rear door glass sub-assembly, be careful not to strike the rear door glass channel sub-assembly with too much force.
68104
21.INSTALL REAR DOOR GLASS SUB-ASSEMBLY
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Insert the rear door glass sub-assembly into the rear door panel as indicated by the arrows, in the order shown in the illustration.
Do not damage the rear door glass sub-assembly.
Slide the rear door glass sub-assembly to install it as shown in the illustration.
68124B
22.INSTALL REAR DOOR QUARTER WINDOW GLASS
Install the rear door quarter window glass to the rear door quarter window weatherstrip.
|
Install in this Direction |
Install the rear door quarter window glass with rear door quarter window weatherstrip as shown in the illustration.
67408F
23.INSTALL REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY
|
Screw |
|
Bolt |
Install the rear door rear lower window frame sub-assembly with the screw and 2 bolts.
67872
24.INSTALL REAR DOOR WEATHERSTRIP
Clean the rear door panel.
Remove the release paper from a new rear door weatherstrip.
After removing the release paper, keep the exposed adhesive free from foreign matter.
| *a | Double-sided Tape |
Engage the 23 clips and install the rear door weatherstrip.
68640A
25.INSTALL REAR DOOR CHECK ASSEMBLY
Clean the bolt hole in the vehicle body.
Clean the threads of the bolt.
Apply adhesive to the threads of the bolt.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
|
Nut |
|
Bolt |
Install the rear door check assembly with the 2 nuts and bolt.
68152C
26.INSTALL REAR DOOR GLASS RUN
Install the rear door glass run.
67858B
27.INSTALL REAR DOOR PANEL PROTECTOR
Install the rear door panel protector.
Engage the clip.
67848A
28.INSTALL REAR DOOR NO. 1 VENT SEAL
Install the rear door No. 1 vent seal.
67842E
29.INSTALL REAR DOOR SERVICE HOLE COVER
Engage the 8 clips to install the rear door service hole cover.
Engage the 2 clamps.
Connect the connector.
67674A
30.INSTALL REAR DOOR FRAME GARNISH
Engage the 2 claws to install the rear door frame garnish.
86160B
31.INSTALL REAR SPEAKER ASSEMBLY
69206C
32.INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY
Engage the 3 claws to install the rear door inside handle sub-assembly.
67844A
33.INSTALL REAR DOOR NO. 2 SERVICE HOLE COVER
|
Install in this Direction |
Install the rear door No. 2 service hole cover to the rear door inner glass weatherstrip.
65907E
34.INSTALL REAR CURTAIN SUB-ASSEMBLY (w/ Rear Door Sunshade)
Engage the 3 guides.
Install the rear curtain sub-assembly with the 9 screws.
68174A
35.INSTALL REAR DOOR INNER GLASS WEATHERSTRIP
|
Install in this Direction |
Install the rear door inner glass weatherstrip with rear door No. 2 service hole cover as shown in the illustration.
Engage the clip.
67604
36.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY
Install the No. 1 door scuff plate clamp as shown in the illustration.
| *1 | Rear Door Inside Locking Cable Assembly |
| *2 | Rear Door Lock Remote Control Cable Assembly |
|
Install in this Direction |
Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly to the rear door inside handle sub-assembly as shown in the illustration.
Engage the 5 claws and guide.
Engage the 7 clips to install the rear door trim board sub-assembly.
Install the 3 screws.
74260
37.INSTALL REAR ARMREST ASSEMBLY
|
Install in this Direction |
Engage the guide as shown in the illustration.
|
Install in this Direction |
Engage the 3 clips, 8 claws and 2 guides to install the rear armrest assembly as shown in the illustration.
38.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL
Connect the connector.
|
Install in this Direction |
Engage the 2 clips 5 claws and 6 guides to install the rear power window regulator switch assembly with rear door upper armrest base panel as shown in the illustration.
74038B
39.INSTALL REAR DOOR ARMREST COVER SUB-ASSEMBLY
Engage the 3 claws to install the rear door armrest cover sub-assembly.
40.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
41. INITIALIZE POWER WINDOW CONTROL SYSTEM
42.INSPECT POWER WINDOW OPERATION