Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM (w/o Parking Support Brake System)
RM33C0E _56 Audio / Visual / Telematics _065452 PARK ASSIST / MONITORING _0333740 TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/o Parking Support Brake System) J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/o Parking Support Brake System)  Clearance Warning Buzzer Circuit  


DESCRIPTION

This circuit consists of the No. 1 clearance warning buzzer and clearance warning ECU assembly. An ECU-excited type buzzer is used. The ECU operates the buzzers using a sound pattern that changes depending on the distance to the obstacle.

WIRING DIAGRAM

E220929E55
1.979,1.354 2.073,1.51 0.094,0.156 10 false 1 3.271,1.354 3.365,1.51 0.094,0.156 10 false 2 1.667,2.021 2.208,2.365 0.542,0.344 10 false K74 1.667,2.146 4.26,2.365 2.594,0.219 10 false No. 1 Clearance Warning Buzzer 4.292,2.021 4.906,2.302 0.615,0.281 10 false R39 4.292,2.188 7.021,2.427 2.729,0.24 10 false Clearance Warning ECU Assembly 4.698,0.615 4.906,0.771 0.208,0.156 10 false 14 4.948,0.708 5.281,0.865 0.333,0.156 10 false CBZ 4.698,1.354 4.875,1.51 0.177,0.156 10 false 13 4.948,1.438 5.156,1.594 0.208,0.156 10 false EF 2.135,1.354 2.396,1.552 0.26,0.198 10 false Z+ 3.052,1.354 3.313,1.552 0.26,0.198 10 false Z-

PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / IPA/ICS/Clearance Sonar / Active Test.


e.

Check that the buzzer operates by performing the Active Test.

Body Electrical > IPA/ICS/Clearance Sonar > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Buzzer No. 1 clearance warning buzzer Operate or Stop Confirm that the vehicle is stopped and the power switch is on (IG)
Body Electrical > IPA/ICS/Clearance Sonar > Active Test
Tester Display
Buzzer
50004 170 4
OK:

The No. 1 clearance warning buzzer sounds.


Result:
Proceed to
OK
NG




OK

NG

2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - NO. 1 CLEARANCE WARNING BUZZER)
2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - NO. 1 CLEARANCE WARNING BUZZER)
a.

Disconnect the R39 clearance warning ECU assembly connector.


b.

Disconnect the K74 No. 1 clearance warning buzzer connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R39-14 (CBZ) - K74-1 (Z+) Always Below 1 Ω
R39-13 (EF) - K74-2 (Z-) Always Below 1 Ω
R39-14 (CBZ) or K74-1 (Z+) - Body ground Always 10 kΩ or higher
R39-13 (EF) or K74-2 (Z-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE NO. 1 CLEARANCE WARNING BUZZER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE NO. 1 CLEARANCE WARNING BUZZER

Result:
Proceed to
NEXT



NEXT

4.PERFORM ACTIVE TEST USING GTS
4.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / IPA/ICS/Clearance Sonar / Active Test.


e.

Check that the buzzer operates by performing the Active Test.

Body Electrical > IPA/ICS/Clearance Sonar > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Buzzer No. 1 clearance warning buzzer Operate or Stop Confirm that the vehicle is stopped and the power switch is on (IG)
Body Electrical > IPA/ICS/Clearance Sonar > Active Test
Tester Display
Buzzer
50004 170 4
OK:

The No. 1 clearance warning buzzer sounds.


Result:
Proceed to
OK
NG




OK

END

NG