Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM
RM33C0E _56 Audio / Visual / Telematics _065452 PARK ASSIST / MONITORING _0333741 REAR VIEW MONITOR SYSTEM Y

PARK ASSIST / MONITORING  REAR VIEW MONITOR SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the rear view monitor system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
a.

Ask the customer about the problems and the conditions at the time the malfunction occurred to make sure the problem symptom was not temporarily caused by radio waves in the surrounding environment.

HINT:

The rear view monitor display may be temporarily distorted due to radio waves around the vehicle.

Problem Symptom Cause
Both of the following conditions are met:
·

The problem symptom indicates a rear view monitor display malfunction and the problem symptom cannot be reproduced.

·

DTC C1622 is output as "Hist" only.*


The display may be temporarily distorted when the vehicle is close to an object that transmits radio waves, such as a telecommunication tower, an airport or a truck equipped with a transceiver.

*: DTCs output as "Hist" will not be output again after DTCs are cleared.




Result:
Proceed to
NEXT



NEXT

3.INSPECT AUXILIARY BATTERY VOLTAGE
3.INSPECT AUXILIARY BATTERY VOLTAGE
a.

Measure the auxiliary battery voltage with the power switch off.

Standard Voltage:

11 to 14 V


HINT:

If the voltage is below 11 V, replace or recharge the auxiliary battery before proceeding to the next step.



Result:
Proceed to
NEXT



NEXT

4.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
4.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
a.

Use the GTS to check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
CAN communication system DTCs are not output A
CAN communication system DTCs are output B



A

5.CHECK FOR DTC*

B

5.CHECK FOR DTC*
a.

Check for DTCs and note any codes that are output.

Body Electrical > Navigation System > Trouble Codes
50001 212

b.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs. Try to reproduce the DTC by simulating the conditions indicated by the DTCs.

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
No DTCs are output A
DTCs are output B



A

6.PROBLEM SYMPTOM CONFIRMATION

B

11.ADJUST, REPAIR OR REPLACE
6.PROBLEM SYMPTOM CONFIRMATION
Result:
Result Proceed to
Symptom does not occur A
Symptom occurs B



A

7.SYMPTOM SIMULATION

B

8.CHECK IF SAME SYMPTOM APPEARS IN OTHER SYSTEM
7.SYMPTOM SIMULATION

NEXT

8.CHECK IF SAME SYMPTOM APPEARS IN OTHER SYSTEM
8.CHECK IF SAME SYMPTOM APPEARS IN OTHER SYSTEM


*1: w/o Navigation System

*2: w/ Navigation System


Result:
Result Proceed to
Symptom does not appear A
Symptom appears (w/o Navigation System) B
Symptom appears (w/ Navigation System) C



A

9.PROBLEM SYMPTOMS TABLE

B

C

9.PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table A
Fault is listed in Problem Symptoms Table B



A

10.PERFORM TROUBLESHOOTING BASED ON MALFUNCTION SYMPTOM

B

11.ADJUST, REPAIR OR REPLACE
10.PERFORM TROUBLESHOOTING BASED ON MALFUNCTION SYMPTOM

Result:
Proceed to
NEXT



NEXT

11.ADJUST, REPAIR OR REPLACE
11.ADJUST, REPAIR OR REPLACE
Result:
Proceed to
NEXT



NEXT

12.CONFIRMATION TEST
12.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END