Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM33C0E _56 Audio / Visual / Telematics _065452 PARK ASSIST / MONITORING _0333742 BLIND SPOT MONITOR SYSTEM Y

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the blind spot monitor system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
HINT:

If there are any scratches or impact marks on the rear bumper, perform the blind spot monitor beam axis confirmation. If any abnormalities are found, perform the blind spot monitor sensor installation condition inspection.


Result:
Proceed to
NEXT



NEXT

3.INSPECT AUXILIARY BATTERY VOLTAGE
3.INSPECT AUXILIARY BATTERY VOLTAGE
a.

Measure the auxiliary battery voltage with the power switch off.

Standard Voltage:

11 to 14 V


If the voltage is below 11 V, replace or recharge the auxiliary battery before proceeding to the next step.


Result:
Proceed to
NEXT



NEXT

4.CHECK CAN COMMUNICATION SYSTEM*
4.CHECK CAN COMMUNICATION SYSTEM*
a.

Use the GTS to check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
CAN communication system DTCs are not output. A
CAN communication system DTCs are output. B



A

5.CHECK FOR DTC AND FREEZE FRAME DATA*

B

5.CHECK FOR DTC AND FREEZE FRAME DATA*
a.

Refer to DTC Check / Clear for the blind spot monitor system.

Body Electrical > Blind Spot Monitor Master > Trouble Codes
50001 313
Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314

b.

Record or print DTCs and freeze frame data, if necessary.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>FREEZE FRAME DATA


Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

6.PROBLEM SYMPTOMS TABLE

B

6.PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table. A
Fault is listed in Problem Symptoms Table. B


HINT:

If the symptom does not recur and no DTCs are output, attempt to reproduce the symptoms.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



A

7.PERFORM TROUBLESHOOTING BASED ON MALFUNCTION SYMPTOM*

B

7.PERFORM TROUBLESHOOTING BASED ON MALFUNCTION SYMPTOM*

NEXT

8.ADJUST, REPAIR OR REPLACE
8.ADJUST, REPAIR OR REPLACE
Result:
Result Proceed to
When adjusting or repairing A
When replacing B



A

9.CLEAR DTC*

B

10.PERFORM BEAM AXIS INSPECTION
9.CLEAR DTC*
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Master > Clear DTCs
50002 313
Body Electrical > Blind Spot Monitor Slave > Clear DTCs
50002 314
Result:
Proceed to
NEXT




NEXT

10.PERFORM BEAM AXIS INSPECTION
10.PERFORM BEAM AXIS INSPECTION
a.

Enter Test Mode (refer to Blind Spot Monitor Beam Axis Inspection).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>OPERATION CHECK


b.

Confirm the blind spot monitor beam axis display and perform the blind spot monitor beam axis adjustment.


Result:
Proceed to
NEXT



NEXT

11.PERFORM CONFIRMATION TEST*
11.PERFORM CONFIRMATION TEST*
Result:
Proceed to
NEXT



NEXT

END