Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT AXLE HUB › 2017.09–2019.02
RM33C0E _52 Drivetrain _065436 AXLE AND DIFFERENTIAL _0334218 FRONT AXLE HUB A

AXLE AND DIFFERENTIAL  FRONT AXLE HUB  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front axle hub sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ steering control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)

NOTICE:
·

When removing or installing the front disc brake caliper assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C1214 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this step.

·

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISABLE BRAKE CONTROL

Hide 3.REMOVE FRONT WHEEL

Hide 89543 5.SEPARATE FRONT SPEED SENSOR

a.
C369722

Remove the bolt and separate the front speed sensor and front flexible hose from the front shock absorber assembly.

NOTICE:

Be sure to separate the front speed sensor and front flexible hose from the front shock absorber assembly completely.



b.
C369723

Remove the bolt, disengage the clamp and separate the front speed sensor from the front shock absorber assembly and steering knuckle.

NOTICE:
·

Prevent foreign matter from contacting the sensor tip.

·

Be careful not to damage the front speed sensor.

·

Clean the speed sensor installation hole and the contact surfaces every time the front speed sensor is removed.




Hide 45470 6.SEPARATE TIE ROD ASSEMBLY

Hide 7.SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY

Hide 43512 8.REMOVE FRONT DISC

Hide 48069 9.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY

a.
C369724

Remove the bolt and 2 nuts and separate the front lower No. 1 suspension arm sub-assembly from the front lower ball joint assembly.


Hide 43420 10.SEPARATE FRONT DRIVE SHAFT ASSEMBLY

a.
C369725C01
2.74,0.406 3.146,0.406 3.146,0.406 3.146,1.573 true 2.885,0.667 3.146,0.667 true 3.094,1.583 3.406,1.74 0.313,0.156 10 false *a
*a Matchmark


Put matchmarks on the front drive shaft assembly and the front axle hub sub-assembly.


b.
C369726

Using a plastic hammer, separate the front drive shaft assembly from the front axle assembly.

NOTICE:
·

Do not damage the front drive shaft outboard joint boot.

·

Do not push the front axle assembly towards the outside of the vehicle any further than necessary.



HINT:

If it is difficult to separate the front drive shaft assembly from the front axle assembly, tap the end of the front drive shaft assembly using a brass bar and a hammer.



Hide 11.REMOVE FRONT AXLE ASSEMBLY

a.
C369727

Remove the 2 bolts, 2 nuts and front axle assembly from the front shock absorber assembly.

NOTICE:

When removing the nuts, keep the bolts from rotating.



Hide 43502C 12.REMOVE FRONT AXLE HUB SUB-ASSEMBLY

a.
C369728

Secure the front axle assembly between aluminum plates in a vise.

NOTICE:

Do not overtighten the vise.



b.

Remove the 4 bolts, front axle hub sub-assembly and front disc brake dust cover from the steering knuckle.

NOTICE:
·

Do not drop the front axle hub sub-assembly.

·

Be careful not to damage the speed sensor rotor or contact surfaces.

·

Do not allow foreign matter to contact the speed sensor rotor or contact surfaces.