Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY
RM33C0E _52 Drivetrain _065435 DRIVE SHAFT / PROPELLER SHAFT _0328128 FRONT DRIVE SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front drive shaft assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT WHEELS

Hide 53851M 2.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH

Hide 53852K 3.REMOVE FRONT WHEEL OPENING EXTENSION PAD LH

Hide 51441 4.REMOVE NO. 1 ENGINE UNDER COVER

Hide 5.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY (w/ Cover)

Hide 53737B 6.REMOVE FRONT FENDER APRON SEAL LH

Hide 53736 7.REMOVE FRONT FENDER APRON SEAL RH

Hide 43502H 9.REMOVE FRONT AXLE SHAFT NUT

a.
C370393N01
2.448,1.135 2.448,0.656 2.448,0.656 2.771,0.656 true 2.802,0.552 3.177,0.74 0.375,0.188 10 true SST

Using SST and a hammer, release the staked part of the front axle shaft nut.

SST
09930-00010  

NOTICE:

Fully loosen the staked part of the front axle shaft nut, otherwise the threads of the drive shaft may be damaged.



b.

While applying the brakes, remove the front axle shaft nut.


Hide 89543 10.SEPARATE FRONT SPEED SENSOR

Hide 45470 11.SEPARATE TIE ROD ASSEMBLY

Hide 48810 12.SEPARATE FRONT STABILIZER LINK ASSEMBLY

Hide 48069 13.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY

Hide 14.SEPARATE FRONT DRIVE SHAFT ASSEMBLY

Hide 43420 15.REMOVE FRONT DRIVE SHAFT ASSEMBLY LH

a.
C377778N01
2.104,1.646 1.26,1.875 1.26,1.875 1.896,1 true 0.958,1.844 1.417,2.042 0.458,0.198 10 false SST

Using SST, remove the front drive shaft assembly LH.

SST
09520-01010  
09520-24010  (09520-32040)

NOTICE:
·

Do not damage the front drive shaft oil seal LH.

·

Do not damage the front axle inboard joint boot.

·

Do not drop the front drive shaft assembly LH.




Hide 43410 16.REMOVE FRONT DRIVE SHAFT ASSEMBLY RH

a.
C377779

Remove the 2 bolts and pull out the drive shaft together with the drive shaft bearing case sub-assembly.


b.

Remove the front drive shaft assembly RH from the drive shaft bearing bracket.

NOTICE:
·

Do not damage the front drive shaft oil seal RH.

·

Do not damage the front axle inboard joint boot.

·

Do not drop the front drive shaft assembly RH.



HINT:

If it is difficult to disengage the fitting, tap the end of the front drive inboard joint assembly with a brass bar and a hammer.



Hide 43420G 17.REMOVE FRONT DRIVE SHAFT HOLE SNAP RING

a.
C183640

Using a screwdriver, remove the front drive shaft hole snap ring.