Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT AXLE HUB › 2017.09–2019.02
RM33C0E _52 Drivetrain _065436 AXLE AND DIFFERENTIAL _0334218 FRONT AXLE HUB G

AXLE AND DIFFERENTIAL  FRONT AXLE HUB  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front axle hub sub-assembly on-vehicle inspection are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ steering control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)

NOTICE:
·

When removing or installing the front disc brake caliper assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C1214 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this step.

·

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISABLE BRAKE CONTROL

Hide 3.REMOVE FRONT WHEEL

Hide 47313J 4.SEPARATE FRONT FLEXIBLE HOSE

Hide 5.SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY

Hide 43512 6.REMOVE FRONT DISC

Hide 7.INSPECT FRONT AXLE HUB BEARING LOOSENESS

a.
C373232

Using a dial indicator with magnetic base, check for looseness near the center of the front axle hub sub-assembly.

Maximum Looseness:

0.05 mm (0.00196 in.)


NOTICE:
·

Ensure that the dial indicator is set perpendicular to the measurement surface.

·

Keep the magnet of the dial indicator away from the front axle hub sub-assembly and front speed sensor.



HINT:

If the looseness exceeds the maximum, replace the front axle hub sub-assembly.



Hide 8.INSPECT FRONT AXLE HUB RUNOUT

a.
C373233

Using a dial indicator with magnetic base, check for runout on the surface of the front axle hub sub-assembly outside the front axle hub bolts.

Maximum Runout:

0.05 mm (0.00196 in.)


NOTICE:
·

Ensure that the dial indicator is set perpendicular to the measurement surface.

·

Make sure to set the tip of the dial indicator towards the outside of the front axle hub bolts.

·

Keep the magnet of the dial indicator away from the front axle hub sub-assembly and front speed sensor.



HINT:

If the runout exceeds the maximum, replace the front axle hub sub-assembly.



Hide 43512 9.INSTALL FRONT DISC

Hide 10.INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY

Hide 47313J 11.INSTALL FRONT FLEXIBLE HOSE

Hide 12.INSTALL FRONT WHEEL

Hide 13.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

a.

Connect the reservoir level switch connector.


b.

Connect the cable to the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>AUXILIARY BATTERY>INSTALLATION


c.

Turn the power switch on (READY).


d.

Depress the brake pedal and release it.