Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › ULTRASONIC SENSOR (for Front) › 2017.09–2019.02
RM33C0E _56 Audio / Visual / Telematics _065452 PARK ASSIST / MONITORING _0334379 ULTRASONIC SENSOR(for Front) A

PARK ASSIST / MONITORING  ULTRASONIC SENSOR(for Front)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during ultrasonic sensor removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link
Replacement of ultrasonic sensor Adjust TOYOTA parking assist-sensor system TOYOTA parking assist-sensor system (Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT BUMPER ASSEMBLY

Hide 89341K 2.REMOVE FRONT CORNER ULTRASONIC SENSOR

a.

for Bar Type Radiator Grille:

i.
E375826C01
0,0 0,0 false
V113147

Remove in this Direction


Disconnect the connector.


ii.

Disengage the claw as shown in the illustration.


iii.
E375828C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws and remove the front corner ultrasonic sensor as shown in the illustration.



b.

for Mesh Type Radiator Grille:

i.
E375830

Disconnect the connector.


ii.
E375831C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws and remove the front corner ultrasonic sensor as shown in the illustration.



Hide 89348J 3.REMOVE ULTRASONIC SENSOR CLIP (for Bar Type Radiator Grille)

HINT:

Perform this procedure only when replacement of the ultrasonic sensor clip is necessary.


a.
E375835

Disengage the clamp to remove the ultrasonic sensor clip from the wire.


Hide 89347B 4.REMOVE FRONT CORNER ULTRASONIC SENSOR RETAINER

HINT:
·

Perform this procedure only when replacement of the front corner ultrasonic sensor retainer is necessary.

·

When removing the front corner ultrasonic sensor retainer, heat the front bumper assembly and front corner ultrasonic sensor retainer using a heat light.



a.

Heat the front bumper assembly and front corner ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.

Heating Temperature:
Item Temperature
Front Bumper Assembly 40 to 60°C (104 to 140°F)
Front Corner Ultrasonic Sensor Retainer


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.




b.

for Bar Type Radiator Grille:

i.
E375833

Remove the front corner ultrasonic sensor retainer.



c.

for Mesh Type Radiator Grille:

i.
E375834

Remove the front corner ultrasonic sensor retainer.



Hide 89305 5.REMOVE ULTRASONIC SENSOR CUSHION SET

HINT:

Only perform this procedure when removing and installing the ultrasonic sensor cushion set.


a.

Remove the ultrasonic sensor cushion set as shown in the illustration.

E488344C01
0,0 0,0 false
V113147

Remove in this Direction - -