Home › Vehicle Exterior › DOOR / HATCH › FUEL LID OPENER SYSTEM › 2017.09–2018.08
RM33C0E _59 Vehicle Exterior _065469 DOOR / HATCH _0333676 FUEL LID OPENER SYSTEM J

DOOR / HATCH  FUEL LID OPENER SYSTEM  Fuel Lid Opener does not Operate  


DESCRIPTION

When the fuel lid opener switch is pushed, a fuel lid opener switch signal is sent to the ECM. The ECM turns on the FUEL OPN relay and EFI-MAIN NO. 1 relay, and the fuel lid lock with motor assembly opens the fuel lid. When the fuel lid is open, a fuel lid courtesy switch signal is output from the fuel lid lock with motor assembly.

WIRING DIAGRAM

B479764E01
0.292,0.906 1.167,1.792 0.875,0.885 10 false from Auxiliary Battery 0.302,3.125 1.177,4.01 0.875,0.885 10 false from Auxiliary Battery 1.49,1.073 3.635,1.271 2.146,0.198 10 false EFI-MAIN NO. 1 2.802,0.813 2.958,1.01 0.156,0.198 10 false 1 2.802,1.24 2.958,1.438 0.156,0.198 10 false 3 4.115,0.802 4.271,1 0.156,0.198 10 false 2 4.115,1.24 4.271,1.438 0.156,0.198 10 false 5 5.333,0.802 5.646,1 0.313,0.198 10 false 15 5.604,0.917 6.219,1.115 0.615,0.198 10 false MREL 5.333,2.552 5.646,2.75 0.313,0.198 10 false 44 5.604,2.667 6.219,2.865 0.615,0.198 10 false FREL 4.448,2.448 4.76,2.646 0.313,0.198 10 false 20 4.448,2.927 4.76,3.125 0.313,0.198 10 false 28 4.448,2.656 4.76,2.854 0.313,0.198 10 false 3C 4.448,3.135 4.76,3.333 0.313,0.198 10 false 3D 2.469,2.458 2.781,2.656 0.313,0.198 10 false 30 2.469,2.667 2.781,2.865 0.313,0.198 10 false 3C 2.458,3.135 2.771,3.333 0.313,0.198 10 false 3C 2.51,2.927 2.667,3.125 0.156,0.198 10 false 7 1.646,2.813 3.021,3.01 1.375,0.198 10 false EFI-NO. 1 1.604,3.302 2.833,3.5 1.229,0.198 10 false FUEL OPN 3.177,3.438 4.406,3.635 1.229,0.198 10 false FUEL OPN 3.042,1.635 5.188,1.833 2.146,0.198 10 false EFI-MAIN NO. 1 2.76,3.948 4.375,4.635 1.615,0.688 10 false Instrument Panel Junction Block Assembly 4.167,5.01 4.323,5.208 0.156,0.198 10 false B 4.167,5.625 4.323,5.823 0.156,0.198 10 false B 2.802,5.615 2.958,5.813 0.156,0.198 10 false E 2.594,5.615 2.75,5.813 0.156,0.198 10 false 2 4.375,5.01 4.531,5.208 0.156,0.198 10 false 1 4.385,5.625 4.542,5.823 0.156,0.198 10 false 3 5.333,5.625 5.646,5.823 0.313,0.198 10 false 31 5.604,5.74 6.219,5.938 0.615,0.198 10 false LIDO 2.469,6.042 2.781,6.24 0.313,0.198 10 false W4 2.469,6.198 4.875,6.875 2.406,0.677 10 false Fuel Lid Lock with Motor Assembly 2.781,7.052 2.938,7.25 0.156,0.198 10 false 2 4.104,7.052 4.26,7.25 0.156,0.198 10 false 5 2.99,7.052 3.146,7.25 0.156,0.198 10 false E 3.844,7.052 4.156,7.25 0.313,0.198 10 false IG 2.813,7.469 3.271,7.667 0.458,0.198 10 false K38 2.813,7.635 6.177,7.833 3.365,0.198 10 false Fuel Lid Opener Switch 5.323,7.052 5.635,7.25 0.313,0.198 10 false 38 5.615,7.156 6.229,7.354 0.615,0.198 10 false FUEL 6.125,7.875 6.583,8.073 0.458,0.198 10 false A22 6.115,8.031 6.573,8.229 0.458,0.198 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK FOR DTCs (HEALTH CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Health Check.


e.

Check DTCs.


Result:
Result Proceed to
No DTCs are output. A
DTCs are output. B



A

2.CHECK EVAPORATIVE EMISSION CONTROL SYSTEM

B

GO TO DTC CHART

2.CHECK EVAPORATIVE EMISSION CONTROL SYSTEM
a.

Perform the Evaporative System Check using the GTS (Automatic Mode). Refer to "CONFIRMATION DRIVING PATTERN" of P045011.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>P045011


b.

Check for DTCs.

Powertrain > Engine > Trouble Codes
50001 372
OK:

Evaporative emission control system DTCs are not output.



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS (Activate the Fuel Filler Opener)

NG

3.PERFORM ACTIVE TEST USING GTS (Activate the Fuel Filler Opener)
a.

Enter the following menus: Powertrain / Engine / Active Test.


b.

Perform the Active Test according to the display on the GTS.

Powertrain > Engine > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Activate the Fuel Filler Opener Fuel lid lock with motor assembly OFF/ON -
Powertrain > Engine > Active Test
Tester Display
Activate the Fuel Filler Opener
50004 372 41

OK:

The fuel lid lock with motor assembly operates normally.


Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (Fuel Lid SW)

NG

10.INSPECT FUEL LID LOCK WITH MOTOR ASSEMBLY
4.READ VALUE USING GTS (Fuel Lid SW)
a.

Enter the following menus: Powertrain / Engine / Data List.


b.

Read the Data List according to the display on the GTS.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Fuel Lid SW Fuel lid opener switch status Close or Open Close: Fuel lid opener switch not pushed
Open: Fuel lid opener switch pushed
-
Powertrain > Engine > Data List
Tester Display
Fuel Lid SW
50003 372 37

OK:

The GTS display changes correctly in response to the operation of the fuel lid opener switch.


Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (Fuel Lid Sensor SW)

NG

8.INSPECT FUEL LID OPENER SWITCH
5.READ VALUE USING GTS (Fuel Lid Sensor SW)
a.

Enter the following menus: Powertrain / Engine / Data List.


b.

Read the Data List according to the display on the GTS.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Fuel Lid Sensor SW Fuel lid courtesy switch status Close or Open Close: Fuel lid closed
Open: Fuel lid open
-
Powertrain > Engine > Data List
Tester Display
Fuel Lid Sensor SW
50003 372 38

OK:

The GTS display changes correctly in response to the operation of the fuel lid courtesy switch (fuel lid lock with motor assembly).


Result:
Proceed to
OK
NG



OK

NG

6.INSPECT FUEL LID LOCK WITH MOTOR ASSEMBLY (FUEL LID COURTESY SWITCH)
6.INSPECT FUEL LID LOCK WITH MOTOR ASSEMBLY (FUEL LID COURTESY SWITCH)
a.

Remove the fuel lid lock with motor assembly.

Click hereVehicle Exterior>DOOR / HATCH>FUEL LID OPENER MOTOR ASSEMBLY>REMOVAL


b.

Inspect the fuel lid lock with motor assembly (fuel lid courtesy switch).

Click hereVehicle Exterior>DOOR / HATCH>FUEL LID OPENER MOTOR ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (FUEL LID LOCK WITH MOTOR ASSEMBLY - ECM)

NG

REPLACE FUEL LID LOCK WITH MOTOR ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (FUEL LID LOCK WITH MOTOR ASSEMBLY - ECM)
a.

Disconnect the A22 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W4-3 (B) - A22-31 (LIDO) Always Below 1 Ω
W4-3 (B) or A22-31 (LIDO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT FUEL LID OPENER SWITCH
a.

Remove the fuel lid opener switch.

Click hereVehicle Exterior>DOOR / HATCH>FUEL LID OPENER SWITCH>REMOVAL


b.

Inspect the fuel lid opener switch.

Click hereVehicle Exterior>DOOR / HATCH>FUEL LID OPENER SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (FUEL LID OPENER SWITCH - ECM AND BODY GROUND)

NG

REPLACE FUEL LID OPENER SWITCH

9.CHECK HARNESS AND CONNECTOR (FUEL LID OPENER SWITCH - ECM AND BODY GROUND)
a.

Disconnect the A22 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K38-5 (IG) - A22-38 (FUEL) Always Below 1 Ω
K38-2 (E) - Body ground Always Below 1 Ω
K38-5 (IG) or A22-38 (FUEL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT FUEL LID LOCK WITH MOTOR ASSEMBLY
a.

Remove the fuel lid lock with motor assembly.

Click hereVehicle Exterior>DOOR / HATCH>FUEL LID OPENER MOTOR ASSEMBLY>REMOVAL


b.

Inspect the fuel lid lock with motor assembly (motor operation).

Click hereVehicle Exterior>DOOR / HATCH>FUEL LID OPENER MOTOR ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - EFI-MAIN RELAY AND AUXILIARY BATTERY)

NG

REPLACE FUEL LID LOCK WITH MOTOR ASSEMBLY

11.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - EFI-MAIN RELAY AND AUXILIARY BATTERY)
a.

Disconnect the 3C instrument panel junction block assembly connector.


b.
B429545C06
1.479,0.083 1.906,0.323 0.427,0.24 1.615,0.125 1.927,0.323 0.313,0.198 10 false 3C 0.177,0.156 0.49,0.354 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3C-7 - Body ground Power switch off 11 to 14 V
3C-30 - Body ground Power switch on (IG) 11 to 14 V
Power switch off and fuel lid opener switch not pressed → fuel lid opener switch pressed Below 1 V → 11 to 14 V



Result:
Result Proceed to
OK A
The result for terminal 3C-7 is not as specified. B
The result for terminal 3C-30 (with power switch on (IG)) is not as specified.
The result for terminal 3C-30 (with power switch off and fuel lid opener switch pressed) is not as specified. C



A

12.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ECM)

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

C

12.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ECM)
a.

Disconnect the A22 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3C-20 - A22-44 (FREL) Always Below 1 Ω
3C-20 or A22-44 (FREL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - FUEL LID LOCK WITH MOTOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - FUEL LID LOCK WITH MOTOR ASSEMBLY)
a.

Disconnect the 3D instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3D-28 - W4-1 (B) Always Below 1 Ω
3D-28 or W4-1 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Replace the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

15.CHECK FUEL LID OPEN OPERATION
15.CHECK FUEL LID OPEN OPERATION
a.

Check that the fuel lid can be opened.

Click hereVehicle Exterior>DOOR / HATCH>FUEL LID OPENER SYSTEM>OPERATION CHECK


OK:

The fuel lid can be opened.


Result:
Proceed to
OK
NG



OK

END (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WAS DEFECTIVE)

NG