CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
| *A | for LHD | *B | for RHD |
Disconnect the instrument panel junction block assembly and main body ECU (multiplex network body ECU) connectors.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 3B-3 - Body ground | LA - Body ground | Ground | Always | Below 1 Ω |
| 3B-23 - Body ground | B - Body ground | Auxiliary battery power supply | Power switch off | 11 to 14 V |
| 3F-1 - Body ground*1 | W - Body ground | Auxiliary battery power supply | Power switch off | 11 to 14 V |
| 3G-1 - Body ground*2 | W - Body ground | Auxiliary battery power supply | Power switch off | 11 to 14 V |
*1: for LHD
*2: for RHD
Connect the instrument panel junction block assembly and main body ECU (multiplex network body ECU) connectors.
Measure the voltage and resistance, and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 3C-19 - Body ground | BE - Body ground | BKUP LP relay drive output | Power switch off, shift lever not in R | Below 1 V |
| Power switch on (IG), shift lever in R | 11 to 14 V | |||
| 3C-25 - Body ground*1 | BE - Body ground | FOG FR relay drive output | Light control switch in tail or head position, fog light switch in front position | Below 1 V |
| Light control switch in tail or head position, fog light switch off position | 11 to 14 V | |||
| 3C-31 - Body ground | V - Body ground | H-LP LH relay drive output | ·
Power switch on (IG) or within 15 seconds after power switch turned off ·
Taillights on |
Below 1 V |
·
15 seconds or more after power switch turned off ·
Taillights off |
11 to 14 V | |||
| 3C-32 - Body ground*1 | LA-B - Body ground | Tail signal output | Taillights on | 11 to 14 V |
| Taillights off | Below 1 V | |||
| 3D-10 - Body ground | LG - Body ground | Back-up lights drive output | Power switch off, shift lever not in R | Below 1 V |
| Power switch on (IG), shift lever in R | 11 to 14 V | |||
| 3D-21 - Body ground*2 | LG - Body ground | Rear fog light drive output | Light control switch in tail or head position, fog light switch in rear position | 11 to 14 V |
| Light control switch in tail or head position, fog light switch off position | Below 1 V | |||
| 3D-30 - Body ground | LA-B - Body ground | Taillights, rear side marker lights*4 and license plate lights drive output | Taillights on | 11 to 14 V |
| Taillights off | Below 1 V | |||
| K51-19 (GND2) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| K51-23 (AHID) - Body ground*3 | BE - Body ground | Auto high beam switch indicator drive output | Power switch on (IG), auto high beam switch on | Below 1 V |
| Power switch on (IG), auto high beam switch off | 11 to 14 V | |||
| K52-12 (HRY2) - Body ground | BE - Body ground | H-LP RH relay drive output | ·
Power switch on (IG) or within 15 seconds after power switch turned off ·
Taillights on |
Below 1 V |
·
15 seconds or more after power switch turned off ·
Taillights off |
11 to 14 V | |||
| K52-16 (HEAD) - Body ground | LG - Body ground | Light control switch head position input | Light control switch in head position | Below 1 V |
| Light control switch not in head position | 11 to 14 V | |||
| K52-23 (CLTB) - K52-25 (CLTE) | BE - GR | Automatic light control sensor power supply output | Power switch off | Below 1 V |
| Power switch on (IG) | 11 to 14 V | |||
| K52-24 (CLTS) - Body ground | R - Body ground | Automatic light control sensor signal input | Power switch off | Below 1 V |
| Power switch on (IG) | Pulse generation
(See waveform 1) |
|||
| K52-26 (AHBI) - Body ground*3 | B - Body ground | Auto high beam switch signal input | Auto high beam switch on | Below 1 V |
| Auto high beam switch off | 11 to 14 V |
*1: w/ Front Fog Light
*2: w/ Rear Fog Light
*3: w/ Automatic High Beam System
*4: w/ Rear Side Marker Light
Waveform 1
| Item | Content |
|---|---|
| Tester Connection | K52-24 (CLTS) - Body ground |
| Tool setting | 2 V/DIV., 10 ms./DIV. |
| Condition | Power switch on (IG) |
The communication waveform changes according to the surrounding brightness.
CHECK HEADLIGHT ECU SUB-ASSEMBLY LH (for Bulb Type Turn Signal Light)
Disconnect the A10 headlight ECU sub-assembly LH connector.
Measure the voltage and resistance on the wire harness side connector according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A10-4 (IG) - Body ground | B - Body ground | Ignition power supply | Power switch off | Below 1 V |
| Power switch on (IG) | 11 to 14 V | |||
| A10-12 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| A10-13 (ECUB) - Body ground | B - Body ground | Auxiliary battery power supply | ·
15 seconds or more after power switch turned off ·
Taillights off |
Below 1 V |
·
Power switch on (IG) or within 15 seconds after power switch turned off ·
Taillights on |
9.5 to 14 V |
Connect the A10 headlight ECU sub-assembly LH connector.
Since the A10 headlight ECU sub-assembly LH connector is a waterproof type connector, the voltage and pulses cannot be checked directly. The values listed are for reference only.
Since the B headlight ECU sub-assembly LH connector is connected inside the headlight assembly, the voltage and pulses cannot be checked directly. The values listed are for reference only.
Measure the voltage and check of pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A10-11 (TNS) - Body ground | LA-LG - Body ground | Front turn signal light signal input | Power switch on (IG), front turn signal light off | Below 1 V |
| Power switch on (IG), front turn signal light blinking | 11 to 14 V ←→ Below 1 V | |||
| A10-16 (SBR) - A10-15 (SGR) | LG - G | Rear height control sensor sub-assembly LH power supply | Power switch on (IG) | 4.75 to 5.25 V |
| A10-17 (SHRL) - A10-15 (SGR) | BE - G | Rear height control sensor sub-assembly LH signal input | Power switch on (IG), vehicle unloaded, vehicle stopped | Approximately 2.5 V
(value decreases as the front of the vehicle is raised) |
| A10-23 (CANL) - Body ground | W - Body ground | CAN communication line | Power switch off | Below 1 V |
| Power switch on (IG) | Pulse generation | |||
| A10-24 (CANH) - Body ground | P - Body ground | CAN communication line | Power switch off | Below 1 V |
| Power switch on (IG) | Pulse generation | |||
| B-4 (LOLED2) - B-3 (LOLED0) | - | Low beam headlights drive output | Low beam headlights off | Below 1 V |
| Low beam headlights on | 10 to 16 V | |||
| B-6 (FANB) - B-14 (FANG) | - | Headlight fan power source | Low beam headlights off | Below 1 V |
| Low beam headlights on | 4.75 to 5.25 V | |||
| B-7 (ACTBI) - B-17 (ACTGI) | - | Headlight leveling motor power source | Power switch off | Below 1 V |
| Power switch on (IG) | 11 to 14 V | |||
| B-8 (ACTSI) - B-17 (ACTGI) | - | Headlight leveling motor signal output | Power switch on (IG), low beam headlights on, vehicle height not changed | Below 1 V |
| Power switch on (IG), low beam headlights on, vehicle height changed and maintained for more than 3 seconds | 1.0 to 14 V | |||
| B-9 (TURN+) - B-13 (TURN-) | - | Front turn signal light signal output | Power switch on (IG), front turn signal light off | Below 1 V |
| Power switch on (IG), front turn signal light blinking | 11 to 14 V ←→ Below 1 V | |||
| B-10 (HI+) - B-1 (HI-) | - | High beam headlights drive output | High beam headlights off | Below 1 V |
| High beam headlights on | 11 to 14 V | |||
| B-15 (FANP) - B-14 (FANG) | - | Headlight fan control signal input | Low beam headlights off | Below 1 V |
| Low beam headlights on | Pulse generation | |||
| B-19 (CLL+) - B-11 (DRL-) | - | Clearance lights/daytime running lights control signal output | Clearance lights and daytime running lights off | Below 1 V |
| Clearance lights and daytime running lights on | 11 to 14 V | |||
| B-20 (DRL+) - B-11 (DRL-) | - | Clearance lights/daytime running lights power source | Clearance lights and daytime running lights off | Below 1 V |
| Clearance lights and daytime running lights on | 11 to 14 V |
CHECK HEADLIGHT ECU SUB-ASSEMBLY LH (for LED Type Turn Signal Light)
Disconnect the A10 headlight ECU sub-assembly LH connector.
Measure the voltage and resistance on the wire harness side connector according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A10-4 (IG) - Body ground | B - Body ground | Ignition power supply | Power switch off | Below 1 V |
| Power switch on (IG) | 11 to 14 V | |||
| A10-12 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| A10-13 (ECUB) - Body ground | B - Body ground | Auxiliary battery power supply | ·
15 seconds or more after power switch turned off ·
Taillights off |
Below 1 V |
·
Power switch on (IG) or within 15 seconds after power switch turned off ·
Taillights on |
9.5 to 14 V |
Connect the A10 headlight ECU sub-assembly LH connector.
Since the A10 headlight ECU sub-assembly LH connector is a waterproof type connector, the voltage and pulses cannot be checked directly. The values listed are for reference only.
Since the B headlight ECU sub-assembly LH connector is connected inside the headlight assembly, the voltage and pulses cannot be checked directly. The values listed are for reference only.
Measure the voltage and check of pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A10-11 (TNS) - Body ground | LA-LG - Body ground | Front turn signal light signal input | Power switch on (IG), front turn signal light off | Below 1 V |
| Power switch on (IG), front turn signal light blinking | 11 to 14 V ←→ Below 1 V | |||
| A10-16 (SBR) - A10-15 (SGR) | LG - G | Rear height control sensor sub-assembly LH power supply | Power switch on (IG) | 4.75 to 5.25 V |
| A10-17 (SHRL) - A10-15 (SGR) | BE - G | Rear height control sensor sub-assembly LH signal input | Power switch on (IG), vehicle unloaded, vehicle stopped | Approximately 2.5 V
(value decreases as the front of the vehicle is raised) |
| A10-23 (CANL) - Body ground | W - Body ground | CAN communication line | Power switch off | Below 1 V |
| Power switch on (IG) | Pulse generation | |||
| A10-24 (CANH) - Body ground | P - Body ground | CAN communication line | Power switch off | Below 1 V |
| Power switch on (IG) | Pulse generation | |||
| B-4 (LOLED2) - B-5 (LOLED1) | - | Low beam headlights drive output | Low beam headlights off | Below 1 V |
| Low beam headlights on | 10 to 16 V | |||
| B-6 (FANB) - B-14 (FANG) | - | Headlight fan power source | Low beam headlights off | Below 1 V |
| Low beam headlights on | 4.75 to 5.25 V | |||
| B-7 (ACTBI) - B-17 (ACTGI) | - | Headlight leveling motor power source | Power switch off | Below 1 V |
| Power switch on (IG) | 11 to 14 V | |||
| B-8 (ACTSI) - B-17 (ACTGI) | - | Headlight leveling motor signal output | Power switch on (IG), low beam headlights on, vehicle height not changed | Below 1 V |
| Power switch on (IG), low beam headlights on, vehicle height changed and maintained for more than 3 seconds | 1.0 to 14 V | |||
| B-9 (TURN+) - B-13 (TURN-) | - | Front turn signal light signal output | Power switch on (IG), front turn signal light off | Below 1 V |
| Power switch on (IG), front turn signal light blinking | 11 to 14 V ←→ Below 1 V | |||
| B-10 (HI+) - B-1 (HI-) | - | High beam headlights drive output | High beam headlights off | Below 1 V |
| High beam headlights on | 11 to 14 V | |||
| B-15 (FANP) - B-14 (FANG) | - | Headlight fan control signal input | Low beam headlights off | Below 1 V |
| Low beam headlights on | Pulse generation | |||
| B-16 (PWM1) - B-11 (DRL-) | - | Clearance lights/daytime running lights control signal output | Clearance lights and daytime running lights off | Below 1 V |
| Clearance lights and daytime running lights on | Pulse generation | |||
| B-20 (DRL+) - B-11 (DRL-) | - | Clearance lights/daytime running lights power source | Clearance lights and daytime running lights off | Below 1 V |
| Clearance lights and daytime running lights on | 11 to 14 V |
CHECK HEADLIGHT ECU SUB-ASSEMBLY RH (for Bulb Type Turn Signal Light)
Disconnect the A11 headlight ECU sub-assembly RH connector.
Measure the voltage and resistance on the wire harness side connector according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A11-4 (IG) - Body ground | B - Body ground | Ignition power supply | Power switch off | Below 1 V |
| Power switch on (IG) | 11 to 14 V | |||
| A11-12 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| A11-13 (ECUB) - Body ground | BE - Body ground | Auxiliary battery power supply | ·
15 seconds or more after power switch turned off ·
Taillights off |
Below 1 V |
·
Power switch on (IG) or within 15 seconds after power switch turned off ·
Taillights on |
9.5 to 14 V |
Connect the A11 headlight ECU sub-assembly RH connector.
Since the A11 headlight ECU sub-assembly RH connector is a waterproof type connector, the voltage and pulses cannot be checked directly. The values listed are for reference only.
Since the B headlight ECU sub-assembly RH connector is connected inside the headlight assembly, the voltage and pulses cannot be checked directly. The values listed are for reference only.
Measure the voltage and check of pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A11-7 (HLC) - Body ground* | W - Body ground | Headlight cleaner motor operation signal | Power switch on (IG), light control switch head and headlight cleaner motor not operating | 11 to 14 V |
| Power switch on (IG), light control switch head and headlight cleaner operating | Below 1.5 V | |||
| A11-11 (TNS) - Body ground | LA-G - Body ground | Front turn signal light signal input | Power switch on (IG), front turn signal light off | Below 1 V |
| Power switch on (IG), front turn signal light blinking | 11 to 14 V ←→ Below 1 V | |||
| A11-23 (CANL) - Body ground | W - Body ground | CAN communication line | Power switch off | Below 1 V |
| Power switch on (IG) | Pulse generation | |||
| A11-24 (CANH) - Body ground | L - Body ground | CAN communication line | Power switch off | Below 1 V |
| Power switch on (IG) | Pulse generation | |||
| B-4 (LOLED2) - B-3 (LOLED0) | - | Low beam headlights drive output | Low beam headlights off | Below 1 V |
| Low beam headlights on | 10 to 16 V | |||
| B-6 (FANB) - B-14 (FANG) | - | Headlight fan power source | Low beam headlights off | Below 1 V |
| Low beam headlights on | 4.75 to 5.25 V | |||
| B-7 (ACTBI) - B-17 (ACTGI) | - | Headlight leveling motor power source | Power switch off | Below 1 V |
| Power switch on (IG) | 11 to 14 V | |||
| B-8 (ACTSI) - B-17 (ACTGI) | - | Headlight leveling motor signal output | Power switch on (IG), low beam headlights on, vehicle height not changed | Below 1 V |
| Power switch on (IG), low beam headlights on, vehicle height changed and maintained for more than 3 seconds | 1.0 to 14 V | |||
| B-9 (TURN+) - B-13 (TURN-) | - | Front turn signal light signal output | Power switch on (IG), front turn signal light off | Below 1 V |
| Power switch on (IG), front turn signal light blinking | 11 to 14 V ←→ Below 1 V | |||
| B-10 (HI+) - B-1 (HI-) | - | High beam headlights drive output | High beam headlights off | Below 1 V |
| High beam headlights on | 11 to 14 V | |||
| B-15 (FANP) - B-14 (FANG) | - | Headlight fan control signal input | Low beam headlights off | Below 1 V |
| Low beam headlights on | Pulse generation | |||
| B-19 (CLL+) - B-11 (DRL-) | - | Clearance lights/daytime running lights control signal output | Clearance lights and daytime running lights off | Below 1 V |
| Clearance lights and daytime running lights on | 11 to 14 V | |||
| B-20 (DRL+) - B-11 (DRL-) | - | Clearance lights/daytime running lights power source | Clearance lights and daytime running lights off | Below 1 V |
| Clearance lights and daytime running lights on | 11 to 14 V |
*: w/ Headlight Cleaner System
CHECK HEADLIGHT ECU SUB-ASSEMBLY RH (for LED Type Turn Signal Light)
Disconnect the A11 headlight ECU sub-assembly RH connector.
Measure the voltage and resistance on the wire harness side connector according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A11-4 (IG) - Body ground | B - Body ground | Ignition power supply | Power switch off | Below 1 V |
| Power switch on (IG) | 11 to 14 V | |||
| A11-12 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| A11-13 (ECUB) - Body ground | BE - Body ground | Auxiliary battery power supply | ·
15 seconds or more after power switch turned off ·
Taillights off |
Below 1 V |
·
Power switch on (IG) or within 15 seconds after power switch turned off ·
Taillights on |
9.5 to 14 V |
Connect the A11 headlight ECU sub-assembly RH connector.
Since the A11 headlight ECU sub-assembly RH connector is a waterproof type connector, the voltage and pulses cannot be checked directly. The values listed are for reference only.
Since the B headlight ECU sub-assembly RH connector is connected inside the headlight assembly, the voltage and pulses cannot be checked directly. The values listed are for reference only.
Measure the voltage and check of pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A11-7 (HLC) - Body ground* | W - Body ground | Headlight cleaner motor operation signal | Power switch on (IG), light control switch head and headlight cleaner motor not operating | 11 to 14 V |
| Power switch on (IG), light control switch head and headlight cleaner operating | Below 1.5 V | |||
| A11-11 (TNS) - Body ground | LA-G - Body ground | Front turn signal light signal input | Power switch on (IG), front turn signal light off | Below 1 V |
| Power switch on (IG), front turn signal light blinking | 11 to 14 V ←→ Below 1 V | |||
| A11-23 (CANL) - Body ground | W - Body ground | CAN communication line | Power switch off | Below 1 V |
| Power switch on (IG) | Pulse generation | |||
| A11-24 (CANH) - Body ground | L - Body ground | CAN communication line | Power switch off | Below 1 V |
| Power switch on (IG) | Pulse generation | |||
| B-4 (LOLED2) - B-5 (LOLED1) | - | Low beam headlights drive output | Low beam headlights off | Below 1 V |
| Low beam headlights on | 10 to 16 V | |||
| B-6 (FANB) - B-14 (FANG) | - | Headlight fan power source | Low beam headlights off | Below 1 V |
| Low beam headlights on | 4.75 to 5.25 V | |||
| B-7 (ACTBI) - B-17 (ACTGI) | - | Headlight leveling motor power source | Power switch off | Below 1 V |
| Power switch on (IG) | 11 to 14 V | |||
| B-8 (ACTSI) - B-17 (ACTGI) | - | Headlight leveling motor signal output | Power switch on (IG), low beam headlights on, vehicle height not changed | Below 1 V |
| Power switch on (IG), low beam headlights on, vehicle height changed and maintained for more than 3 seconds | 1.0 to 14 V | |||
| B-9 (TURN+) - B-13 (TURN-) | - | Front turn signal light signal output | Power switch on (IG), front turn signal light off | Below 1 V |
| Power switch on (IG), front turn signal light blinking | 11 to 14 V ←→ Below 1 V | |||
| B-10 (HI+) - B-1 (HI-) | - | High beam headlights drive output | High beam headlights off | Below 1 V |
| High beam headlights on | 11 to 14 V | |||
| B-15 (FANP) - B-14 (FANG) | - | Headlight fan control signal input | Low beam headlights off | Below 1 V |
| Low beam headlights on | Pulse generation | |||
| B-16 (PWM1) - B-11 (DRL-) | - | Clearance lights/daytime running lights control signal output | Clearance lights and daytime running lights off | Below 1 V |
| Clearance lights and daytime running lights on | Pulse generation | |||
| B-20 (DRL+) - B-11 (DRL-) | - | Clearance lights/daytime running lights power source | Clearance lights and daytime running lights off | Below 1 V |
| Clearance lights and daytime running lights on | 11 to 14 V |
*: w/ Headlight Cleaner System
CHECK COMBINATION METER ASSEMBLY
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU
CHECK FORWARD RECOGNITION CAMERA (w/ Automatic High Beam System)
Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>TERMINALS OF ECU
CHECK STEERING SENSOR
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU
CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY