| Detection Item | Symptom | Trouble Area |
|---|---|---|
| Door Mirror ECU RH Communication Stop Mode | Any of the following conditions are met:
·
·
|
·
Outer mirror control ECU assembly (for front passenger side) branch line or connector (for LHD) ·
Power source circuit of outer mirror control ECU assembly (for front passenger side) (for LHD) ·
Outer mirror control ECU assembly (for front passenger side) ground circuit (for LHD) ·
Outer mirror control ECU assembly (for front passenger side) (for LHD) ·
Outer mirror control ECU assembly (for driver side) branch line or connector (for RHD) ·
Power source circuit of outer mirror control ECU assembly (for driver side) (for RHD) ·
Outer mirror control ECU assembly (for driver side) ground circuit (for RHD) ·
Outer mirror control ECU assembly (for driver side) (for RHD) |
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
Inspect the fuses for circuits related to this system before performing the following procedure.
Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
Check vehicle type.
| Result | Proceed to |
|---|---|
| for LHD | A |
| for RHD | B |
A
B
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the N9 outer mirror control ECU assembly (for front passenger side) connector.
| *a | Front view of wire harness connector
(to Outer Mirror Control ECU Assembly (for Front Passenger Side)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N9-9 (CANP) - N9-8 (CANN) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Outer Mirror Control ECU Assembly (for Front Passenger Side)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N9-7 (GND) - Body ground | Cable disconnected from negative (-) auxiliary battery terminal | Below 1 Ω |
Reconnect the cable to the negative (-) auxiliary battery terminal.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N9-5 (SIG) - Body ground | Power switch on (IG) | 11 to 14 V |
| N9-6 (CPUB) - Body ground | Power switch off | 11 to 14 V |
| N9-14 (BDR) - Body ground | Power switch off | 11 to 14 V |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the N9 outer mirror control ECU assembly (for driver side) connector.
| *a | Front view of wire harness connector
(to Outer Mirror Control ECU Assembly (for Driver Side)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N9-9 (CANP) - N9-8 (CANN) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Outer Mirror Control ECU Assembly (for Driver Side)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N9-7 (GND) - Body ground | Cable disconnected from negative (-) auxiliary battery terminal | Below 1 Ω |
Reconnect the cable to the negative (-) auxiliary battery terminal.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N9-5 (SIG) - Body ground | Power switch on (IG) | 11 to 14 V |
| N9-6 (CPUB) - Body ground | Power switch off | 11 to 14 V |
| N9-14 (BDR) - Body ground | Power switch off | 11 to 14 V |
| Result |
|---|
| OK |
| NG |
OK
NG