CHECK FOR INSTALLED SYSTEMS (ECUS AND SENSORS) THAT USE CAN COMMUNICATION
The systems (ECUs and sensors) that use CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed to the vehicle.
GTS display and installed systems
The names of ECUs and sensors shown on the GTS display may differ from those shown in DTC Table by ECU.
| Connected to | Code | ECU/Sensor Name | GTS Display | Applicability |
|---|---|---|---|---|
| - | CGW | Central gateway ECU (network gateway ECU) | - | Installed on all vehicles |
| - | DLC3 | DLC3 | - | Installed on all vehicles |
| Bus 1 | F-CAM | Forward recognition camera | Front Camera Module | Vehicles with Toyota Safety Sense |
| F-MR | Millimeter wave radar sensor assembly | Front Radar | Vehicles with Toyota Safety Sense | |
| GRS | Swing grille actuator assembly | Grill Shutter | Vehicles with Grille Shutter System | |
| BSM | Blind spot monitor sensor RH | Blind Spot Monitor Master | Vehicles with Blind Spot Monitor System | |
| CS | Clearance warning ECU assembly | Clearance Warning (Clearance Sonar) | Vehicles with TOYOTA Parking Assist-sensor System | |
| R-CA | Rear television camera assembly | Parking Assist Monitor System / Rear Camera | Vehicles with Parking Assist Monitor System | |
| Bus 2 | HV | Hybrid vehicle control ECU assembly | Hybrid Vehicle Control | Installed on all vehicles |
| F-MGC | Inverter with converter assembly | Motor Generator | Installed on all vehicles | |
| BRK | Brake booster with master cylinder assembly | Skid Control (ABS/VSC/TRAC) | Installed on all vehicles | |
| ENG | ECM | ECM (Engine) | Installed on all vehicles | |
| Bus 3 | AV | Radio and display receiver assembly | Display and Navigation (AVN) | Vehicles with Radio and Display Type |
| YGW | Option connector (bus buffer ECU) | Accessory Gateway | Vehicles with CAN Compatible Optional Devices | |
| Bus 4 | TPMS | Tire pressure warning ECU and receiver | Tire Pressure | Vehicles with Tire Pressure Warning System and Tire Inflation Pressure Display Function |
| OCS | Occupant detection ECU | Occupant Detection | Vehicles with Occupant Classification System | |
| BRK | Brake booster with master cylinder assembly | Skid Control (ABS/VSC/TRAC) | Installed on all vehicles | |
| EPS | Rack and pinion power steering gear assembly | Power Steering (EPS) | Installed on all vehicles | |
| PKB | Brake actuator assembly | Electric Parking Brake | Installed on all vehicles | |
| ENG | ECM | ECM (Engine) | Installed on all vehicles | |
| HV | Hybrid vehicle control ECU assembly | Hybrid Vehicle Control | Installed on all vehicles | |
| STR | Steering sensor | Spiral cable (Steering Angle Sensor) | Installed on all vehicles | |
| SRS | Airbag sensor assembly | Airbag | Installed on all vehicles | |
| Bus 5 | LITS | Headlight ECU sub-assembly RH | HL AutoLeveling/AFS/AHS (Sub) | Vehicles with Automatic Headlight Beam Level Control System |
| MIR-R | Outer mirror control ECU assembly (for front passenger side) | Front Door RH/R-Mirror (FR-Door/R-Mirror) | LHD vehicles with Seat Position Memory System | |
| Outer mirror control ECU assembly (for driver side) | Front Door RH/R-Mirror (FR-Door/R-Mirror) | RHD vehicles with Seat Position Memory System | ||
| DST | Position control ECU assembly LH | D-Seat | LHD vehicles with Seat Position Memory System | |
| Position control ECU assembly RH | D-Seat | RHD vehicles with Seat Position Memory System | ||
| MIR-L | Outer mirror control ECU assembly (for driver side) | Front Door LH/L-Mirror (FL-Door/L-Mirror) | LHD vehicles with Seat Position Memory System | |
| Outer mirror control ECU assembly (for front passenger side) | Front Door LH/L-Mirror (FL-Door/L-Mirror) | RHD vehicles with Seat Position Memory System | ||
| LITM | Headlight ECU sub-assembly LH | HL AutoLeveling/AFS/AHS | Vehicles with Automatic Headlight Beam Level Control System | |
| A/C | Air conditioning amplifier assembly | Air Conditioning Amplifier | Installed on all vehicles | |
| SMT | Certification ECU (smart key ECU assembly) | Certification (Smart) | Installed on all vehicles | |
| MB | Main body ECU (multiplex network body ECU) | Main Body | Installed on all vehicles | |
| HUD | Meter mirror sub-assembly | Head Up Display | Vehicles with Headup Display System | |
| T&T | Multiplex tilt and telescopic ECU | Multiplex Tilt and Telescopic | Vehicles with Power Tilt and Power Telescopic System | |
| MET | Combination meter assembly | Combination Meter | Installed on all vehicles |
Description of "Communication Bus Check" Screen
The following communication bus check screen is provided only as an example. This screen differs from the actual screen for this vehicle.
The ECUs and sensors that are normally connected to the CAN communication system are displayed on the GTS.
Select "Communication Bus Check" on the menu screen of the GTS.
If items are not selected correctly in the vehicle specification pop up screen, the name of the CAN junction connector to which the ECUs or sensors are connected may not be displayed on the "Communication Bus Check" screen.
Confirm that the "Communication Bus Check" screen is displayed and the ECUs and sensors that are normally connected to the CAN communication system are displayed.
Even if an ECU or sensor that is connected to a bus that is monitored by a bus monitoring ECU (gateway function equipped ECU) is not communicating, it will remain displayed on the "Communication Bus Check" screen.
When an ECU or sensor that is connected to a bus that is not monitored by a bus monitoring ECU (gateway function equipped ECU) is not displayed on the "Communication Bus Check" screen, it means that it is not communicating.
The default display setting selected on the combo box is ALL. When checking for ECUs or sensors for a specific bus, choose the bus from the drop down list. ALL, each bus, each sub bus and Central Gateway are listed in the drop down list.
| *a | Combo box | *b | Background color is red or yellow |
| Item | Detail |
|---|---|
| Combo box: ALL | Displays all ECUs and sensors connected to the central bus and sub buses. |
| Combo box: Bus | Displays ECUs and sensors connected to the selected bus. |
| Combo box: Sub bus | Displays ECUs and sensors connected to the selected sub bus. |
| Combo box: Central Gateway | Displays all ECUs and sensors connected to the central bus. |
When using the combo box, it may be possible to select a sub bus from the drop down list that does not have any connected ECUs or sensors. This is not a malfunction and occurs when there is no optional device connected to a sub bus which is monitored by a sub bus monitoring ECU (gateway function equipped ECU).
In the drop down list, all sub buses applicable to the model are displayed (e.g. LIN communication sub buses are also displayed). For information on sub buses necessary to diagnose the CAN communication system, refer to System Diagram.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>SYSTEM DIAGRAM
The background color of an ECU or sensor changes according to its connection status as indicated in the following table.
| Bus Type | Background Color | Connection Status |
|---|---|---|
| Bus | White | Communication has been normal. |
| Yellow | Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication). | |
| Red | Currently not communicating (either of the following):
·
Not communicating since the start of the CAN bus check ·
Communication occurred at least once since the start of the CAN bus check, but is currently not occurring. |
|
| Not displayed | Either of the following:
·
The central gateway ECU (network gateway ECU) has an internal malfunction or cannot communicate with the GTS.*4 ·
No ECUs or sensors are connected to the bus.*5 |
|
| Sub bus with a gateway function equipped ECU that does not memorize connected ECUs or sensors*2 | White | Communication has been normal since the start of the CAN bus check. |
| Yellow | Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication). | |
| Red | Communication occurred at least once since the start of the CAN bus check, but is currently not occurring. | |
| Not displayed | Communication stop has continued since the start of the CAN bus check.*1 | |
| Sub bus with a gateway function equipped ECU that memorizes connected ECUs and sensors*3 | White | Communication has been normal. |
| Yellow | Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication). | |
| Red | Currently not communicating (either of the following):
·
Not communicating since the start of the CAN bus check ·
Communication occurred at least once since the start of the CAN bus check, but is currently not occurring. |
|
| Not displayed | Either of the following:
·
The gateway function equipped ECU cannot communicate with the central gateway ECU (network gateway ECU).*6 ·
No ECUs or sensors are connected to the sub bus.*7 |
Gateway function equipped ECUs relay signals between ECUs and sensors connected to different buses.
*1: An ECU or sensor is installed to the vehicle but is not displayed on the "Communication Bus Check" screen.
*2: The gateway function equipped ECU does not memorize ECUs and sensors connected to its respective sub bus.
*3: The gateway function equipped ECU memorizes ECUs and sensors connected to its respective sub bus.
*4: When the central gateway ECU (network gateway ECU) has an internal malfunction or cannot communicate with the GTS, the name of buses, sub buses, ECUs and sensors will not be displayed.
*5: When no ECUs or sensors are connected to a bus, the message "There is no system found on the communication Bus." will be displayed.
*6: When a gateway function equipped ECU cannot communicate with the central gateway ECU (network gateway ECU), the name of sub buses and ECUs or sensors connected to the sub bus will not be displayed.
*7: When no ECUs or sensors are connected to the sub bus, the message "There is no system found on the communication Bus." will be displayed.
If there is no communication between the GTS and the vehicle, or no ECUs or sensors are displayed as connected, check the central gateway ECU (network gateway ECU) and diagnosis bus (the bus that connects the DLC3 to the central gateway ECU (network gateway ECU)) for malfunctions.
Monitor the screen for any ECU or sensor connection status changes for a period of 2 minutes.
If an open occurs in one of the wires of a CAN branch line, it may interfere with the communication of other ECUs or sensors resulting in an incorrect state being displayed.
If the connection status changes intermittently during the inspection, repair the open in the branch line of the ECU or sensor that is not communicating, and then perform Communication Bus Check again.
Description of "Communication Bus Check (Detail)" Screen
The following communication bus check screen is provided only as an example. This screen differs from the actual screen for this vehicle.
The communication error history of ECUs or sensors which have communication error history can be displayed on the "Communication Bus Check (Detail)" screen.
Select "Communication Bus Check" on the menu screen of the GTS.
If items are not selected correctly in the vehicle specification pop up screen, the name of the CAN junction connector to which the ECUs or sensors are connected may not be displayed on the "Communication Bus Check" screen.
Select "Detail" on the "Communication Bus Check" screen.
| *a | Communication Bus Check (Detail) | - | - |
Confirm that the "Communication Bus Check (Detail)" screen is displayed and the communication error history of the ECUs or sensors up to present is displayed.
Lost Communication Time and Lost Communication Trip are only displayed for the central bus.
Lost Communication Time and Lost Communication Trip are not displayed for sub buses.
The default display setting selected on the combo box is ALL. When checking for ECUs or sensors for a specific bus, choose the bus from the drop down list. ALL, each bus, each sub bus and Central Gateway are listed in the drop down list.
| *a | Combo box | *b | Background color is red |
| Item | Detail |
|---|---|
| Combo box: ALL | Displays all ECUs and sensors connected to the central bus and sub buses. |
| Combo box: Bus | Displays ECUs and sensors connected to the selected bus. |
| Combo box: Sub bus | Displays ECUs and sensors connected to the selected sub bus. |
| Combo box: Central Gateway | Displays all ECUs and sensors connected to the central bus. |
| Bus Monitoring ECU | Displays the gateway function equipped ECU which monitors the selected bus or sub bus. |
| Current Trip | Displays the total number of trips up to now* |
| Lost Communication Time(s) | Displays the longest period of time in seconds that the ECU or sensor connected to the central bus was not communicating. |
| Lost Communication Trip | Displays the trip in which the longest period of time that the ECU or sensor connected to the central bus was not communicating occurred. |
*: If the component has been replaced with a new one, the total number of trips after the replacement is displayed.
The Lost Communication Time column displays the longest period of time in seconds that the central gateway ECU (network gateway ECU) detected a communication stop in the respective ECU or sensor.
The Lost Communication Trip column displays the trip in which the central gateway ECU (network gateway ECU) detected the longest communication stop in the respective ECU or sensor.
When using the combo box, it may be possible to select a sub bus from the drop down list that does not have any connected ECUs or sensors. This is not a malfunction and occurs when there is no optional device connected to a sub bus which is monitored by a sub bus monitoring ECU (gateway function equipped ECU).
In the drop down list, all sub buses applicable to the model are displayed (e.g. LIN communication sub buses are also displayed). For information on sub buses necessary to diagnose CAN communication system, refer to the System Diagram.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>SYSTEM DIAGRAM
The background color of an ECU or sensor changes according to its connection status as indicated in the following table.
| Bus Type | Background Color | Connection Status |
|---|---|---|
| Bus | White | Either of the following:
·
Communication has been normal. ·
Lost Communication Time is below 6 seconds. |
| Red | Lost Communication Time is 6 seconds or more. | |
| Not displayed | Either of the following:
·
The central gateway ECU (network gateway ECU) has an internal malfunction or cannot communicate with the GTS.*1 ·
No ECUs or sensors are connected to the bus.*2 |
|
| Sub bus | White | Lost Communication Time is displayed as "-". |
| Not displayed | Either of the following:
·
The gateway function equipped ECU cannot communicate with the central gateway ECU.*3 ·
No ECUs or sensors are connected to the sub bus.*4 |
If there is no communication between the GTS and the vehicle, or no ECUs or sensors are displayed as connected, check the central gateway ECU (network gateway ECU) and diagnosis bus (the bus that connects the DLC3 to the central gateway ECU (network gateway ECU)) for malfunctions.
Lost Communication Time and Lost Communication Trip are not displayed for sub buses.
*1: When the central gateway ECU (network gateway ECU) has an internal malfunction or cannot communicate with the GTS, the name of buses, sub buses, ECUs and sensors will not be displayed.
*2: When no ECUs or sensors are connected to a bus, the message "There is no system found on the communication Bus." will be displayed.
*3: When a gateway function equipped ECU cannot communicate with the central gateway ECU (network gateway ECU), the name of sub buses and ECUs or sensors connected to the sub bus will not be displayed.
*4: When no ECUs or sensors are connected to the sub bus, the message "There is no system found on the communication Bus." will be displayed.
Communication Bus Check (Communication Malfunction Check)
DTCs related to CAN communication are displayed for each ECU on the GTS.
Select "Communication Bus Check" on the menu screen of the GTS.
Select "Communication Malfunction Check" on the "Communication Bus Check" screen.
| *a | Communication Malfunction Check | - | - |
Confirm that the "Communication Malfunction Check" screen is displayed and CAN communication DTCs for each ECU are displayed.
When there are no CAN communication DTCs stored, no DTCs will be displayed.
How to Use "Communication Bus Check" Screen in Inspection
The following CAN bus wiring diagram or communication bus check screen is provided only as an example. This wiring diagram or screen differs from the actual one for this vehicle.
If the CAN communication system is currently malfunctioning, it is recommended to use Communication Bus Check rather than Communication DTCs for determining the suspected area.
Turn the power switch on (IG), or perform the necessary operations to reproduce the problem symptom, select "Communication Bus Check" and wait approximately 2 minutes. Check the communication status of each ECU or sensor on the screen while performing this operation.
If the CAN communication system is currently malfunctioning, determine the suspected area using Communication Bus Check as follows:
| Problem Symptom Pattern | Display on Communication Bus Check Screen | Suspected Area |
|---|---|---|
| A | Almost all of the ECUs and sensors connected to the malfunctioning CAN bus are displayed as not communicating on the "Communication Bus Check" screen. | ·
Short between CAN bus lines (CANH and CANL) ·
Short to +B in a CAN bus line (CANH or CANL) ·
Short to ground in a CAN bus line (CANH or CANL) |
| B | ECUs or sensors farther from the central gateway ECU (network gateway ECU) than the open in the wires are displayed as not communicating on the "Communication Bus Check" screen. | Open in both wires of a main bus line in the central bus |
| C | One ECU or sensor is displayed as not communicating on the "Communication Bus Check" screen. | ·
Open in both wires of a branch line connected to an ECU or sensor in the central bus ·
Internal malfunction of an ECU or sensor in the central bus ·
Malfunction in the power supplied to an ECU or sensor in the central bus |
| D | No ECUs or sensors are displayed on the "Communication Bus Check" screen. | ·
Internal malfunction of the central gateway ECU (network gateway ECU) ·
Malfunction in the power supplied to the central gateway ECU (network gateway ECU) ·
Open in both wires of the branch line in the diagnosis bus (DLC3 - Central gateway ECU (network gateway ECU)) ·
Short between CAN bus lines (CANH and CANL) in the diagnosis bus (DLC3 - Central gateway ECU (network gateway ECU)) ·
Short to +B in a CAN bus line (CANH or CANL) in the diagnosis bus (DLC3 - Central gateway ECU (network gateway ECU)) ·
Short to ground in a CAN bus line (CANH or CANL) in the diagnosis bus (DLC3 - Central gateway ECU (network gateway ECU)) |
| E | One ECU or sensor is displayed as not communicating in multiple buses on the "Communication Bus Check" screen. | ·
Internal malfunction of an ECU or sensor connected to multiple buses ·
Malfunction in the power supplied to an ECU or sensor connected to multiple buses |
| F | Some ECUs or sensors are displayed as not communicating in the central bus and other ECUs or sensors are displayed as not communicating in a sub bus. | ·
Open in a wire of a branch line connected to an ECU or sensor in the central bus ·
Internal malfunction of an ECU or sensor in the central bus |
| G | A gateway function equipped ECU is displayed as not communicating in the central bus and ECUs and sensors connected to its respective sub bus are not displayed. | ·
Open in both wires of a branch line connected to a gateway function equipped ECU ·
Internal malfunction of a gateway function equipped ECU ·
Malfunction in the power supplied to a gateway function equipped ECU |
| H | One ECU or sensor is displayed as not communicating in a sub bus on the "Communication Bus Check" screen. | ·
Open in both wires of a branch line connected to an ECU or sensor in a sub bus ·
Internal malfunction of an ECU or sensor in a sub bus ·
Malfunction in the power supplied to an ECU or sensor in a sub bus |
| I | ECUs or sensors farther from the sub bus monitoring ECU (gateway function equipped ECU) than the open in the wires are displayed as not communicating on the "Communication Bus Check" screen. | Open in both wires of a main bus line in a sub bus |
Problem Symptom Pattern A
| Details of Malfunction | ·
Short between CAN bus lines (CANH and CANL) in Bus 2 ·
Short to +B in a CAN bus line (CANH or CANL) in Bus 2 ·
Short to ground in a CAN bus line (CANH or CANL) in Bus 2 |
| *a | Bus 2 | *b | Bus 4 |
| *c | Sub bus | *d | Diagnosis bus |
| *e | Location of malfunction | *f | Background color is red |
Due to the malfunction, almost all of the ECUs and sensors connected to Bus 2 will be displayed as not communicating and their background color will be red.
The malfunction in Bus 2 will not affect the other buses.
The malfunctioning part can be determined by inspecting for an open in the main bus line, a short between bus lines or a short to +B or ground.
Make sure to perform the inspection to measure resistances of buses to determine the cause of the malfunction.
| Details of Malfunction | ·
Short between CAN bus lines (CANH and CANL) in Bus 4 ·
Short to +B in a CAN bus line (CANH or CANL) in Bus 4 ·
Short to ground in a CAN bus line (CANH or CANL) in Bus 4 |
| *a | Bus 2 | *b | Bus 4 |
| *c | Sub bus | *d | Diagnosis bus |
| *e | Location of malfunction | *f | Background color is red |
| *g | Not displayed | - | - |
Due to the malfunction, almost all of the ECUs and sensors connected to Bus 4 will be displayed as not communicating and their background color will be red.
The malfunction will not affect the other buses of the central bus. However, the sub bus connected to Bus 4 is likely to be affected. The gateway function equipped ECU connected to Bus 4 will not communicate and consequently the sub bus and its respective ECUs or sensors monitored by the gateway function equipped ECU (sub bus monitoring ECU) will not be displayed, indicating that the gateway function equipped ECU is not communicating with the central gateway ECU (network gateway ECU).
The malfunctioning part can be determined by inspecting for an open in the main bus line, a short between bus lines or a short to +B or ground.
Make sure to perform the inspection to measure resistances of buses to determine the cause of the malfunction.
Problem Symptom Pattern B
| Details of Malfunction | Open in both wires of the main bus line between the CGW and No. 1 CAN junction connector in Bus 2 |
| *a | Bus 2 | *b | Bus 4 |
| *c | Sub bus | *d | Diagnosis bus |
| *e | Location of malfunction | *f | Background color is red |
Due to the malfunction, almost all of the ECUs and sensors connected to Bus 2 will be displayed as not communicating and their background color will be red.
The malfunction in Bus 2 will not affect the other buses.
The malfunctioning part can be determined by inspecting for an open in the main bus line.
Make sure to perform the inspection to measure resistances of buses to determine the cause of the malfunction.
| Details of Malfunction | Open in both wires of the main bus line between the No. 1 CAN junction connector and No. 2 CAN junction connector in Bus 2 |
| *a | Bus 2 | *b | Bus 4 |
| *c | Sub bus | *d | Diagnosis bus |
| *e | Location of malfunction | *f | Background color is red |
Due to the malfunction, ECUs or sensors farther from the CGW than the open in the wires will be displayed as not communicating and their background color will be red.
The malfunction in Bus 2 will not affect the other buses.
The malfunctioning part can be determined by inspecting for an open in the main bus line.
Make sure to perform the inspection to measure resistances of buses to determine the cause of the malfunction.
| Details of Malfunction | Open in both wires of the main bus line between the No. 2 CAN junction connector and ENG in Bus 2 |
| *a | Bus 2 | *b | Bus 4 |
| *c | Sub bus | *d | Diagnosis bus |
| *e | Location of malfunction | *f | Background color is red |
| *g | Pattern 1 | *h | Pattern 2 |
Even when the same part of the main bus line is open, depending on internal electrical noise which changes according to the position of the open in the line, the information displayed on the "Communication Bus Check" screen may differ.
In pattern 2, the information displayed may be the same as when there is an open in both wires in the main bus line between the No. 1 CAN junction connector and No. 2 CAN junction connector, which may make it difficult to determine the malfunctioning part.
The malfunction in Bus 2 will not affect the other buses.
Make sure to perform the inspection to measure resistances of buses to determine the cause of the malfunction.
Problem Symptom Pattern C
| Details of Malfunction | Open in both wires of the branch line connected to F-MGC in Bus 2 |
| *a | Bus 2 | *b | Bus 4 |
| *c | Sub bus | *d | Diagnosis bus |
| *e | Location of malfunction | *f | Background color is red |
The information displayed on the "Communication Bus Check" screen will be the same for an open in both wires of a branch line, an internal malfunction of an ECU or sensor or a malfunction in the power supplied to an ECU or sensor. In this example, the background color of the malfunctioning ECU or sensor will be red.
| Details of Malfunction | ·
Internal malfunction of F-MGC in Bus 2 ·
Malfunction in the power supplied to F-MGC in Bus 2 |
| *a | Bus 2 | *b | Bus 4 |
| *c | Sub bus | *d | Diagnosis bus |
| *e | Location of malfunction | *f | Background color is red |
The information displayed on the "Communication Bus Check" screen will be the same for an open in both wires of a branch line, an internal malfunction of an ECU or sensor or a malfunction in the power supplied to an ECU or sensor. In this example, the background color of the malfunctioning ECU or sensor will be red.
| Details of Malfunction | Open in both wires of the branch line connected to ENG in Bus 4 |
| *a | Bus 2 | *b | Bus 4 |
| *c | Sub bus | *d | Diagnosis bus |
| *e | Location of malfunction | *f | Background color is red |
The malfunction in Bus 4 will not affect the other buses.
Due to the malfunction, although ENG is communicating normally with CGW via Bus 2, it is not communicating with CGW via Bus 4. Consequently, it will be displayed as not communicating in Bus 4.
Problem Symptom Pattern D
| Details of Malfunction | ·
Internal malfunction of the CGW ·
Malfunction in the power supplied to the CGW |
| *a | Bus 2 | *b | Bus 4 |
| *c | Sub bus | *d | Diagnosis bus |
| *e | Location of malfunction | *f | Not displayed |
When there is no communication between the GTS and the vehicle, no ECUs or sensors will be displayed.
| Details of Malfunction | Open in both wires of the branch lines in the diagnosis bus |
| *a | Bus 2 | *b | Bus 4 |
| *c | Sub bus | *d | Diagnosis bus |
| *e | Location of malfunction | *f | Not displayed |
When there is no communication between the GTS and the vehicle, no ECUs or sensors will be displayed.
Problem Symptom Pattern E
| Details of Malfunction | ·
Internal malfunction of BRK ·
Malfunction in the power supplied to BRK |
| *a | Bus 2 | *b | Bus 4 |
| *c | Sub bus | *d | Diagnosis bus |
| *e | Location of malfunction | *f | Background color is red |
The information displayed on the "Communication Bus Check" screen will be the same for an internal malfunction of an ECU or sensor, or a malfunction in the power supplied to an ECU or sensor.
Due to the malfunction, BRK is not communicating with the CGW via both Bus 2 and Bus 4. Consequently, the background color of BRK will be red for both Bus 2 and Bus 4.
Problem Symptom Pattern F
| Details of Malfunction | ·
Open in a wire of the branch line connected to HV in Bus 4 ·
Internal malfunction of HV in Bus 4 |
| *a | Bus 2 | *b | Bus 4 |
| *c | Sub bus | *d | Diagnosis bus |
| *e | Location of malfunction | *f | Background color is red |
| *g | Background color intermittently becomes yellow or red | *h | Not displayed or background color is yellow or red |
In the "Communication Bus check" screen shown in the illustration, electrical noise in the CAN bus caused by an open in a wire in the branch line connected to HV interferes with the communication of MB causing unstable communication. Also, since MB is a gateway function equipped ECU, communication of ECUs connected to its respective sub bus will also be unstable.
In the "Communication Bus Check" screen shown in the illustration, because the background color of HV is red, it is suspected that HV is the most likely cause of the malfunction. Therefore, it is suspected that HV is not communicating.
Problem Symptom Pattern G
| Details of Malfunction | ·
Open in both wires of the branch line connected to MB in Bus 4 ·
Internal malfunction of MB in Bus 4 ·
Malfunction in the power supplied to MB in Bus 4 |
| *a | Bus 2 | *b | Bus 4 |
| *c | Sub bus | *d | Diagnosis bus |
| *e | Location of malfunction | *f | Background color is red |
| *g | Not displayed | - | - |
If there is a communication malfunction in a gateway function equipped ECU, ECUs connected to its respective sub bus will also be affected and will not be displayed.
In the "Communication Bus Check" screen shown in the illustration, MB is a gateway function equipped ECU. Therefore, MB is suspected as not communicating.
Problem Symptoms Pattern H
| Details of Malfunction | ·
Internal malfunction of MIR-L in the sub bus ·
Malfunction in the power supplied to MIR-L in the sub bus |
| *a | Bus 2 | *b | Bus 4 |
| *c | Sub bus | *d | Diagnosis bus |
| *e | Location of malfunction | *f | Background color is red |
The malfunction in the sub bus will not affect the other buses.
When a gateway function equipped ECU memorizes ECUs and sensors connected to its respective sub bus and there is a communication malfunction in one of the ECUs or sensors, the background color of the ECU or sensor will change to red and the ECU or sensor will remain displayed.
The information displayed on the "Communication Bus Check" screen will be the same for an open in both wires of a branch line, an internal malfunction of an ECU or sensor or a malfunction in the power supplied to an ECU or sensor.
| Details of Malfunction | Open in both wires of the branch line connected to MIR-L in the sub bus |
| *a | Bus 2 | *b | Bus 4 |
| *c | Sub bus | *d | Diagnosis bus |
| *e | Location of malfunction | *f | Background color is red |
The malfunction in the sub bus will not affect the other buses.
When a gateway function equipped ECU memorizes ECUs and sensors connected to its respective sub bus and there is a communication malfunction in one of the ECUs or sensors, the background color of the ECU or sensor will change to red and the ECU or sensor will remain displayed.
The information displayed on the "Communication Bus Check" screen will be the same for an open in both wires of a branch line, an internal malfunction of an ECU or sensor or a malfunction in the power supplied to an ECU or sensor.
Problem Symptom Pattern I
| Details of Malfunction | Open in both wires of the main bus line in the sub bus |
| *a | Bus 2 | *b | Bus 4 |
| *c | Sub bus | *d | Diagnosis bus |
| *e | Location of malfunction | *f | Background color is red |
Due to the malfunction, ECUs or sensors farther from the sub bus monitoring ECU (gateway function equipped ECU) than the open in the wires will be displayed as not communicating and their background color will be red.
How to Use "Communication Bus check (Detail)" Screen in Inspection
If the CAN communication system is currently normal but has communication stop history, determine the malfunctioning part using Communication Bus Check (Detail) as follows:
The following CAN bus wiring diagram or communication bus check screen is provided only as an example. This wiring diagram or screen differs from the actual one for this vehicle.
The Lost Communication Time column displays the longest period of time in seconds that the central gateway ECU (network gateway ECU) detected a communication stop in the respective ECU or sensor.
The Lost Communication Trip column displays the trip in which the central gateway ECU (network gateway ECU) detected the longest communication stop in the respective ECU or sensor.
When using the combo box, it may be possible to select a sub bus from the drop down list that does not have any connected ECUs or sensors. This is not a malfunction and occurs when there is no optional device connected to a sub bus which is monitored by a sub bus monitoring ECU (gateway function equipped ECU).
In the drop down list, all sub buses applicable to the model are displayed (e.g. LIN communication sub buses are also displayed). For information on sub buses necessary to diagnose CAN communication system, refer to the System Diagram.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>SYSTEM DIAGRAM
If the CAN communication system is currently malfunctioning, it is recommended to use Communication Bus Check rather than Communication Bus Check (Detail) for determining the suspected area.
The communication error history of ECUs or sensors which have communication error history can be displayed on the "Communication Bus Check (Detail)" screen.
Lost Communication Time and Lost Communication Trip are only displayed for the central bus.
Lost Communication Time and Lost Communication Trip are not displayed for sub buses.
If there is an ECU or sensor displayed with a red background on the "Communication Bus Check (Detail)" screen to indicate that it was not communicating, it is suspected that the ECU or sensor was not communicating.
| Details of Malfunction | Past malfunction in the wire harness or power supplied to F-MGC in Bus 2 |
| *a | Bus 2 | *b | Bus 4 |
| *c | Sub bus | *d | Diagnosis bus |
| *e | Location of malfunction | *f | Background color is red |
| Bus Type | Background Color | Connection Status |
|---|---|---|
| Bus | White | Either of the following:
·
Communication has been normal. ·
Lost Communication Time is below 6 seconds. |
| Red | Lost Communication Time is 6 seconds or more. | |
| Not displayed | Either of the following:
·
The central gateway ECU (network gateway ECU) has an internal malfunction or cannot communicate with the GTS.*1 ·
No ECUs or sensors are connected to the bus.*2 |
|
| Sub bus | White | Lost Communication Time is displayed as "-". |
| Not displayed | Either of the following:
·
The gateway function equipped ECU cannot communicate with the central gateway ECU.*3 ·
No ECUs or sensors are connected to the sub bus.*4 |
Check the values of Lost Communication Trip and Current Trip for the ECUs or sensors that have a red background color.
If the values of Lost Communication Trip and Current Trip are the same for an ECU or sensor, the ECU or sensor is currently not communicating. In this case, it is recommended to use Communication Bus Check rather than Communication Bus Check (Detail) for determining the suspected area.
In the "Communication Bus Check (Detail)" screen shown in the illustration, F-MGC had a communication malfunction in the 10th trip. Thus, it is suspected that F-MGC was not communicating.
*1: When the central gateway ECU (network gateway ECU) has an internal malfunction or cannot communicate with the GTS, the name of buses, sub buses, ECUs and sensors will not be displayed.
*2: When no ECUs or sensors are connected to a bus, the message "There is no system found on the communication Bus." will be displayed.
*3: When a gateway function equipped ECU cannot communicate with the central gateway ECU (network gateway ECU), the name of sub buses and ECUs or sensors connected to the sub bus will not be displayed.
*4: When no ECUs or sensors are connected to the sub bus, the message "There is no system found on the communication Bus." will be displayed.
DTC TABLE BY ECU
In the CAN communication system, the CAN communication DTCs of each ECU can be displayed using the GTS.
If CAN communication system DTCs are output, the malfunction cannot be determined only by the DTCs. Perform troubleshooting according to How to Proceed with Troubleshooting.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
DTCs will only be stored if the Check Procedure is performed when the system is currently malfunctioning.
Hybrid Vehicle Control ECU Assembly / GTS Display "Hybrid Control"
This ECU uses the CAN communication system for DTC communication.
*1: Refer to Hybrid Control System
*2: Although it is displayed as a communication malfunction on the GTS, the DTC is stored when there is an internal malfunction of the air conditioning amplifier assembly.
Refer to Hybrid Control System
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U010087 | Lost Communication with ECM/PCM "A" Missing Message | The hybrid vehicle control ECU assembly does not receive data from the ECM for approximately 1 second or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 1 second or more. ·
The power source voltage of the hybrid vehicle control ECU assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 2 seconds. | ·
MIL illuminates. ·
Master warning light illuminates. |
- | DTC is stored until it is cleared using the GTS. |
| U010487 | Lost Communication with Cruise Control Module Missing Message | The hybrid vehicle control ECU assembly does not receive data from the millimeter wave radar sensor assembly for approximately 2 seconds or more. | All conditions are met:
·
The power switch is on (IG) for approximately 1 second or more. ·
The cruise control main switch is on. ·
The power source voltage of the hybrid vehicle control ECU assembly is 10.5 V or more. |
Turn the cruise control main switch on and wait for at least approximately 3 seconds. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U011087 | Lost Communication with Drive Motor Control Module "A" Missing Message | The hybrid vehicle control ECU assembly does not receive data from the inverter with converter assembly for approximately 1 second or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 1 second or more. ·
The power source voltage of the hybrid vehicle control ECU assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 2 seconds. | Master warning light illuminates. | - | DTC is stored until it is cleared using the GTS. |
| U012287 | Lost Communication with Vehicle Dynamics Control Module Missing Message | The hybrid vehicle control ECU assembly does not receive data from the brake booster with master cylinder assembly for approximately 3 seconds or more. | All conditions are met:
·
The power switch is on (IG) for approximately 1 second or more. ·
The cruise control main switch is on. ·
The power source voltage of the hybrid vehicle control ECU assembly is 10.5 V or more. |
Turn the cruise control main switch on and wait for at least approximately 4 seconds. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U012987 | Lost Communication with Brake System Control Module Missing Message | The hybrid vehicle control ECU assembly does not receive data from the brake booster with master cylinder assembly for approximately 3 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 2 seconds or more. ·
The power source voltage of the hybrid vehicle control ECU assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 5 seconds. | Master warning light illuminates. | - | DTC is stored until it is cleared using the GTS. |
| U014087 | Lost Communication with Body Control Module Missing Message | The hybrid vehicle control ECU assembly does not receive data from the main body ECU (multiplex network body ECU) for approximately 4 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the hybrid vehicle control ECU assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 7 seconds. | Master warning light illuminates. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U015187 | Lost Communication with Restraints Control Module Missing Message | The hybrid vehicle control ECU assembly does not receive data from the airbag sensor assembly for approximately 1 second or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 1 second or more. ·
The power source voltage of the hybrid vehicle control ECU assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 2 seconds. | Master warning light illuminates. | - | DTC is stored until it is cleared using the GTS. |
| U016487 | Lost Communication with HVAC Control Module Missing Message | The hybrid vehicle control ECU assembly does not receive data from the air conditioning amplifier assembly for approximately 11 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the hybrid vehicle control ECU assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 14 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U029387 | Lost Communication with Hybrid/EV Powertrain Control Module Missing Message | The brake booster with master cylinder assembly does not receive data from the hybrid vehicle control ECU assembly for approximately 1 second or more. | All conditions are met:
·
The power switch is on (IG) for approximately 1 second or more. ·
The cruise control main switch is on. ·
Vehicle speed is 5 km/h (3 mph) or more. ·
The power source voltage of the hybrid vehicle control ECU assembly is 10.5 V or more. |
Drive the vehicle at a speed of 5 km/h (3 mph) or more with the cruise control main switch on for approximately 2 seconds or more. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U029A87*1 | Lost Communication with Hybrid/EV Battery Sensor Module Missing Message | The hybrid vehicle control ECU assembly does not receive data from the battery smart unit for approximately 1 second or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 1 second or more. ·
The power source voltage of the hybrid vehicle control ECU assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 2 seconds. | ·
MIL illuminates. ·
Master warning light illuminates. |
- | DTC is stored until it is cleared using the GTS. |
| U042481*2 | HVAC Control Module to Hybrid Powertrain Control Module Invalid Serial Data Received | The hybrid vehicle control ECU assembly receives an abnormal operation value command from the air conditioning amplifier assembly for approximately 4 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 4 seconds or more. ·
The power source voltage of the hybrid vehicle control ECU assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 8 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U110787 | Lost Communication with Power Management Module Missing Message | The hybrid vehicle control ECU assembly does not receive data from the certification ECU (smart key ECU assembly) for approximately 4 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the hybrid vehicle control ECU assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 7 seconds. | Master warning light illuminates. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U117087 | Lost Communication with Brake System Control Module (Secondary CAN Line) Missing Message | The hybrid vehicle control ECU assembly does not receive data from the brake booster with master cylinder assembly for approximately 3 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 2 seconds or more. ·
The power source voltage of the hybrid vehicle control ECU assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 5 seconds. | Master warning light illuminates. | - | DTC is stored until it is cleared using the GTS. |
Inverter with Converter Assembly / GTS Display "Motor Generator"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U010087 | Lost Communication With ECM/PCM "A" Missing Message | The inverter with converter assembly does not receive data from the ECM for approximately 1 second or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 1 second or more. ·
The power source voltage of the inverter with converter assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 3 seconds. | ·
MIL illuminates. ·
Master warning light illuminates. |
- | DTC is stored until it is cleared using the GTS. |
| U029387 | Lost Communication With Hybrid Powertrain Control Module Missing Message | The inverter with converter assembly does not receive data from the hybrid vehicle control ECU assembly for approximately 1 second or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 1 second or more. ·
The power source voltage of the inverter with converter assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 3 seconds. | ·
MIL illuminates. ·
Master warning light illuminates. |
- | DTC is stored until it is cleared using the GTS. |
| U117087 | Lost Communication With Brake System Control Module(ch2) Missing Message | The inverter with converter assembly does not receive data from the brake booster with master cylinder assembly for approximately 3 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 2 seconds or more. ·
The power source voltage of the inverter with converter assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 7 seconds. | Master warning light illuminates. | - | DTC is stored until it is cleared using the GTS. |
ECM / GTS Display "Engine"
This ECU uses the CAN communication system for DTC communication.
*: The ECM stores DTCs for the grille shutter system.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U011087 | Lost Communication with Drive Motor Control Module "A" Missing Message | The ECM does not receive data from the inverter with converter assembly for approximately 6 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the ECM is 10 V or more. |
Turn the power switch on (IG) and wait for at least approximately 15 seconds. | MIL illuminates. | - | DTC is stored until it is cleared using the GTS. |
| U028487 | Lost Communication with Active Grille Air Shutter Module "A" Missing Message | The ECM does not receive data from the swing grille actuator assembly for approximately 11 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the ECM is 10 V or more. |
Turn the power switch on (IG) and wait for at least approximately 25 seconds. | MIL illuminates. | - | DTC is stored until it is cleared using the GTS. |
| U029387 | Lost Communication with Hybrid Powertrain Control Module Missing Message | The ECM does not receive data from the hybrid vehicle control ECU assembly for approximately 1 second or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 1 second or more. ·
The power source voltage of the ECM is 10 V or more. |
Turn the power switch on (IG) and wait for at least approximately 3 seconds. | MIL illuminates. | - | DTC is stored until it is cleared using the GTS. |
| U129387* | Lost Communication between Hybrid Powertrain Control Module and Active Grille Air Shutter Missing Message | The swing grille actuator assembly does not receive data from the hybrid vehicle control ECU assembly for approximately 6 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the swing grille actuator assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 15 seconds. | MIL illuminates. | - | DTC is stored until it is cleared using the GTS. |
Brake Booster with Master Cylinder Assembly / GTS Display "ABS/VSC/TRC"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U0073 | Control Module Communication Bus Off | One of the following conditions is met:
·
A communication error (bus-off status) occurs consecutively for approximately 5 seconds or more. ·
Delayed reception of data from the steering sensor and airbag sensor assembly continues for 1 second or more. ·
The following condition occurs 10 times or more within 60 seconds: -
Delayed reception of data from the steering sensor and airbag sensor assembly occurs once or more within 5 seconds. |
Both conditions are met:
·
The power switch is on (IG) for approximately 1 second or more. ·
The power source voltage of the brake booster with master cylinder assembly is 10 to 17.4 V. |
Turn the power switch on (IG) and wait for at least approximately 61 seconds. | ·
ABS warning light illuminates. ·
Brake warning light / red (malfunction) illuminates. ·
Brake warning light / yellow (minor malfunction) illuminates. ·
Slip indicator light illuminates. ·
Brake hold operated indicator light blinks. |
- | DTC is stored until it is cleared using the GTS. |
| U0110 | Lost Communication With Drive Motor Control Module "A" | The brake booster with master cylinder assembly does not receive data from the inverter with converter assembly for approximately 2 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 1 second or more. ·
The power source voltage of the brake booster with master cylinder assembly is 10 to 17.4 V. |
Turn the power switch on (IG) and wait for at least approximately 3 seconds. | ·
Brake warning light / yellow (minor malfunction) illuminates. ·
Slip indicator light illuminates. ·
Brake hold operated indicator light blinks. |
- | DTC is stored until it is cleared using the GTS. |
| U0120 | Lost Communication With Starter / Generator Control Module | The brake booster with master cylinder assembly does not receive data from the certification ECU (smart key ECU assembly) for approximately 3 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 1 second or more. ·
The power source voltage of the brake booster with master cylinder assembly is 10 to 17.4 V. |
Turn the power switch on (IG) and wait for at least approximately 4 seconds. | Brake warning light / yellow (minor malfunction) illuminates. | - | DTC is stored until it is cleared using the GTS. |
| U0124 | Lost Communication With Lateral Acceleration Sensor Module | Either of the following conditions is met:
·
Delayed reception of data from the airbag sensor assembly continues for 1 second or more. ·
The following condition occurs 10 times or more within 60 seconds: -
Delayed reception of data from the airbag sensor assembly occurs once or more within 5 seconds. |
Both conditions are met:
·
The power switch is on (IG) for approximately 1 second or more. ·
The power source voltage of the brake booster with master cylinder assembly is 10 to 17.4 V. |
Turn the power switch on (IG) and wait for at least approximately 61 seconds. | ·
ABS warning light illuminates. ·
Brake warning light / yellow (minor malfunction) illuminates. ·
Slip indicator light illuminates. ·
Brake hold operated indicator light blinks. |
- | DTC is stored until it is cleared using the GTS. |
| U0126 | Lost Communication With Steering Angle Sensor Module | Either of the following conditions is met:
·
Delayed reception of data from the steering sensor continues for 1 second or more. ·
The following condition occurs 10 times or more within 60 seconds: -
Delayed reception of data from the steering sensor occurs once or more within 5 seconds. |
Both conditions are met:
·
The power switch is on (IG) for approximately 1 second or more. ·
The power source voltage of the brake booster with master cylinder assembly is 10 to 17.4 V. |
Turn the power switch on (IG) and wait for at least approximately 61 seconds. | ·
Slip indicator light illuminates. ·
Brake hold operated indicator light blinks. |
- | DTC is stored until it is cleared using the GTS. |
| U0128 | Lost Communication With EPB Module | The brake booster with master cylinder assembly does not receive data from the brake actuator assembly for approximately 1 second or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 1 second or more. ·
The power source voltage of the brake booster with master cylinder assembly is 10 to 17.4 V. |
Turn the power switch on (IG) and wait for at least approximately 2 seconds. | Brake hold operated indicator light blinks. | - | DTC is stored until it is cleared using the GTS. |
| U0151 | Lost Communication With Restraints Control Module | The brake booster with master cylinder assembly does not receive data from the airbag sensor assembly for approximately 5 seconds or more. | All conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the brake booster with master cylinder assembly is 10 to 17.4 V. ·
Vehicle speed is 7 km/h (4 mph) or more. |
Drive the vehicle at a speed of 7 km/h (4 mph) or more for approximately 8 seconds or more. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0293 | Lost Communication With Hybrid Vehicle Control System | The brake booster with master cylinder assembly does not receive data from the hybrid vehicle control ECU assembly for approximately 2 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 1 second or more. ·
The power source voltage of the brake booster with master cylinder assembly is 10 to 17.4 V. |
Turn the power switch on (IG) and wait for at least approximately 3 seconds. | ·
Brake warning light / yellow (minor malfunction) illuminates. ·
Slip indicator light illuminates. ·
Brake hold operated indicator light blinks. |
- | DTC is stored until it is cleared using the GTS. |
Rack and Pinion Power Steering Gear Assembly / GTS Display "EMPS"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U0126 | Lost Communication with Steering Angle Sensor Module | The rack and pinion power steering gear assembly does not receive data from the steering sensor for approximately 6 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the rack and pinion power steering gear assembly is 9 to 16 V. |
Turn the power switch on (IG) and wait for at least approximately 9 seconds. | - | - | DTC remains stored only while malfunction is occurring. |
| U0129 | Lost Communication with Brake System Control Module | The rack and pinion power steering gear assembly does not receive data from the brake booster with master cylinder assembly for approximately 3 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the rack and pinion power steering gear assembly is 9 to 16 V. |
Turn the power switch on (IG) and wait for at least approximately 6 seconds. | EPS warning light illuminates. | - | DTC remains stored only while malfunction is occurring. |
| U023A | Lost Communication with Front Camera Module | The rack and pinion power steering gear assembly does not receive data from the forward recognition camera for approximately 2 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the rack and pinion power steering gear assembly is 9 to 16 V. |
Turn the power switch on (IG) and wait for at least approximately 5 seconds. | - | - | DTC remains stored only while malfunction is occurring. |
| U0293 | Lost Communication with Hybrid Control Module | The rack and pinion power steering gear assembly does not receive data from the hybrid vehicle control ECU assembly for approximately 300 seconds or more. | All conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the rack and pinion power steering gear assembly is 9 to 16 V. ·
Vehicle speed is 20 km/h (12 mph) or more. |
Drive the vehicle at a speed of 20 km/h (12 mph) or more for approximately 300 seconds or more. | - | - | DTC remains stored only while malfunction is occurring. |
Airbag Sensor Assembly / GTS Display "SRS Airbag"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U0154 | Lost Communication with Restraints Occupant Classification System Module | The airbag sensor assembly does not receive data from the occupant detection ECU for approximately 5 seconds or more. | The power switch is on (IG) for approximately 3 seconds or more. | Turn the power switch on (IG) and wait for at least approximately 8 seconds. | SRS warning light illuminates. | - | DTC is stored until it is cleared using the GTS. |
Occupant Detection ECU / GTS Display "Occupant Detection"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U0125 | Lost Communication With Multi-axis Acceleration Sensor Module | The occupant detection ECU does not receive data from the airbag sensor assembly for approximately 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the occupant detection ECU is 9.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 8 seconds. | SRS warning light illuminates. | - | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication With Brake System Control Module | The occupant detection ECU does not receive data from the brake booster with master cylinder assembly for approximately 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the occupant detection ECU is 9.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 8 seconds. | SRS warning light illuminates. | - | DTC is stored until it is cleared using the GTS. |
Main Body ECU (Multiplex Network Body ECU) / GTS Display "Main Body"
This ECU uses the CAN communication system for DTC communication.
*1: for LHD
*2: for RHD
*3: w/ CAN Compatible Optional Devices
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U0100 | Lost Communication With ECM/PCM "A" | The main body ECU (multiplex network body ECU) does not receive data from the ECM for approximately 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 10 seconds or more. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0101 | Lost Communication with TCM | The main body ECU (multiplex network body ECU) does not receive data from the hybrid vehicle control ECU assembly for approximately 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 10 seconds or more. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0120 | Lost Communication With Starter / Generator Control Module | The main body ECU (multiplex network body ECU) does not receive data from the certification ECU (smart key ECU assembly) for approximately 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximately 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0126 | Lost Communication with Steering Angle Sensor Module | The main body ECU (multiplex network body ECU) does not receive data from the steering sensor for approximately 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximately 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The main body ECU (multiplex network body ECU) does not receive data from the brake booster with master cylinder assembly for approximately 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 10 seconds or more. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0151 | Lost Communication with Restraints Control Module | The main body ECU (multiplex network body ECU) does not receive data from the airbag sensor assembly for approximately 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 10 seconds or more. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Lost Communication with Instrument Panel Cluster (IPC) Control Module | The main body ECU (multiplex network body ECU) does not receive data from the combination meter assembly for approximately 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximately 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0163 | Lost Communication with Navigation Control Module | The main body ECU (multiplex network body ECU) does not receive data from the radio and display receiver assembly for approximately 10 seconds or more. | Both conditions are met:
·
Power source status change (ACC OFF → ON, IG OFF → ON) is detected and approximately 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0164 | Lost Communication with HVAC Control Module | The main body ECU (multiplex network body ECU) does not receive data from the air conditioning amplifier assembly for approximately 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 10 seconds or more. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0182 | Lost Communication with AFS | The main body ECU (multiplex network body ECU) does not receive data from the headlight ECU sub-assembly LH for approximately 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 10 seconds or more. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 20 seconds. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0199 | Lost Communication with "Door Control Module A" | ·
The main body ECU (multiplex network body ECU) does not receive data from the outer mirror control ECU assembly (for front passenger side) for approximately 10 seconds or more.*1 ·
The main body ECU (multiplex network body ECU) does not receive data from the outer mirror control ECU assembly (for driver side) for approximately 10 seconds or more.*2 |
Both conditions are met:
·
The power switch is on (IG) for approximately 10 seconds or more. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0200 | Lost Communication with "Door Control Module B" | ·
The main body ECU (multiplex network body ECU) does not receive data from the outer mirror control ECU assembly (for driver side) for approximately 10 seconds or more.*1 ·
The main body ECU (multiplex network body ECU) does not receive data from the outer mirror control ECU assembly (for front passenger side) for approximately 10 seconds or more.*2 |
Both conditions are met:
·
The power switch is on (IG) for approximately 10 seconds or more. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0208 | Lost Communication with "Seat Control Module A" | ·
The main body ECU (multiplex network body ECU) does not receive data from the position control ECU assembly LH for approximately 10 seconds or more.*1 ·
The main body ECU (multiplex network body ECU) does not receive data from the position control ECU assembly RH for approximately 10 seconds or more.*2 |
Both conditions are met:
·
The power switch is on (IG) for approximately 10 seconds or more. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U023A | Lost Communication With Image Processing Module "A" | The main body ECU (multiplex network body ECU) does not receive data from the forward recognition camera for approximately 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 10 seconds or more. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 20 seconds. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0293 | Lost Communication with Hybrid Powertrain Control Module | The main body ECU (multiplex network body ECU) does not receive data from the hybrid vehicle control ECU assembly for approximately 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 10 seconds or more. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0327 | Software Incompatibility with Vehicle Security Control Module | The main body ECU (multiplex network body ECU) does not receive data from the certification ECU (smart key ECU assembly) for approximately 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximately 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U1106 | Lost Communication with Electric Parking Brake Module | The main body ECU (multiplex network body ECU) does not receive data from the brake actuator assembly for approximately 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 10 seconds or more. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U1115 | Lost Communication with Tilt & Telescopic Module | The main body ECU (multiplex network body ECU) does not receive data from the multiplex tilt and telescopic ECU for approximately 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximately 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U1117* | Lost Communication with Accessory Gateway | The main body ECU (multiplex network body ECU) does not receive data from the option connector (bus buffer ECU) for approximately 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximately 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
Certification ECU (Smart Key ECU Assembly) / GTS Display "Entry&Start"
This ECU uses the CAN communication system for DTC communication.
*: w/ CAN Compatible Optional Devices
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U0100 | Lost Communication With ECM/PCM "A" | The certification ECU (smart key ECU assembly) does not receive data from the ECM for approximately 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximately 10 seconds or more elapse. ·
The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more. |
Turn the power switch on (IG) and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Body Control Module "B" | The certification ECU (smart key ECU assembly) does not receive data from the main body ECU (multiplex network body ECU) for approximately 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximately 10 seconds or more elapse. ·
The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more. |
Turn the power switch on (IG) and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Lost Communication with Instrument Panel Cluster (IPC) Control Module | The certification ECU (smart key ECU assembly) does not receive data from the combination meter assembly for approximately 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximately 10 seconds or more elapse. ·
The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more. |
Turn the power switch on (IG) and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0293 | Lost Communication With Hybrid Vehicle Control System | The certification ECU (smart key ECU assembly) does not receive data from the hybrid vehicle control ECU assembly for approximately 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximately 10 seconds or more elapse. ·
The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more. |
Turn the power switch on (IG) and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U1117* | Lost Communication with Accessory Gateway | The certification ECU (smart key ECU assembly) does not receive data from the option connector (bus buffer ECU) for approximately 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximately 10 seconds or more elapse. ·
The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more. |
Turn the power switch on (IG) and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
Certification ECU (Smart Key ECU Assembly) / GTS Display "Power Source Control"
This ECU uses the CAN communication system for DTC communication.
*: w/ CAN Compatible Optional Devices
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U0140 | Lost Communication with Body Control Module | The certification ECU (smart key ECU assembly) does not receive data from the main body ECU (multiplex network body ECU) for approximately 3 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more. |
Turn the power switch on (IG) and wait for at least approximately 3 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Lost Communication with Instrument Panel Cluster (IPC) Control Module | The certification ECU (smart key ECU assembly) does not receive data from the combination meter assembly for approximately 4 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more. |
Turn the power switch on (IG) and wait for at least approximately 4 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0293 | HV ECU Communication | The certification ECU (smart key ECU assembly) does not receive data from the hybrid vehicle control ECU assembly for approximately 4 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more. |
Turn the power switch on (IG) and wait for at least approximately 4 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U1117* | Lost Communication with Accessory Gateway | The certification ECU (smart key ECU assembly) does not receive data from the option connector (bus buffer ECU) for approximately 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more. |
Turn the power switch on (IG) and wait for at least approximately 5 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
Headlight ECU Sub-assembly LH / GTS Display "HL AutoLeveling"
This ECU uses the CAN communication system for DTC communication.
*: Refer to Lighting System (w/ Automatic Headlight Beam Level Control System).
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U0073 | Control Module Communication Bus Off | The headlight ECU sub-assembly LH does not send/receive data. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the headlight ECU sub-assembly LH is 9.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 3 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0101 | Lost Communication with TCM | The headlight ECU sub-assembly LH does not receive data from the hybrid vehicle control ECU assembly for approximately 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the headlight ECU sub-assembly LH is 9.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 13 seconds. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0126 | Lost Communication with Steering Angle Sensor Module | The headlight ECU sub-assembly LH does not receive data from the steering sensor for approximately 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the headlight ECU sub-assembly LH is 9.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 13 seconds. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The headlight ECU sub-assembly LH does not receive data from the brake booster with master cylinder assembly for approximately 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the headlight ECU sub-assembly LH is 9.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 13 seconds. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Body Control Module "B" | The headlight ECU sub-assembly LH does not receive data from the main body ECU (multiplex network body ECU) for approximately 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the headlight ECU sub-assembly LH is 9.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 13 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Lost Communication with Instrument Panel Cluster (IPC) Control Module | The headlight ECU sub-assembly LH does not receive data from the meter mirror sub-assembly for approximately 30 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the headlight ECU sub-assembly LH is 9.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 33 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0242 | Lost Communication With Headlamp Control Module "B" | The headlight ECU sub-assembly LH does not receive data from the headlight ECU sub-assembly RH for approximately 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the headlight ECU sub-assembly LH is 9.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 13 seconds. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0293 | Lost Communication with Hybrid Vehicle Control System | The headlight ECU sub-assembly LH does not receive data from the hybrid vehicle control ECU assembly for approximately 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the headlight ECU sub-assembly LH is 9.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 13 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U1000* | CAN Communication Failure(Message Registry) | CAN communication malfunction (message register) | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the headlight ECU sub-assembly LH is 9.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 3 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
Headlight ECU Sub-assembly RH / GTS Display "HL AutoLeveling (Sub)"
This ECU uses the CAN communication system for DTC communication.
*: Refer to Lighting System (w/ Automatic Headlight Beam Level Control System).
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U0073 | Control Module Communication Bus Off | The headlight ECU sub-assembly RH does not send/receive data. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the headlight ECU sub-assembly RH is 9.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 3 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0126 | Lost Communication with Steering Angle Sensor Module | The headlight ECU sub-assembly RH does not receive data from the steering sensor for approximately 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the headlight ECU sub-assembly RH is 9.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 13 seconds. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Body Control Module "B" | The headlight ECU sub-assembly RH does not receive data from the main body ECU (multiplex network body ECU) for approximately 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the headlight ECU sub-assembly RH is 9.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 13 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0182 | Lost Communication With Lighting Control Module Front | The headlight ECU sub-assembly RH does not receive data from the headlight ECU sub-assembly LH for approximately 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the headlight ECU sub-assembly RH is 9.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 13 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U1000* | CAN Communication Failure(Message Registry) | CAN communication malfunction (message register) | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the headlight ECU sub-assembly RH is 9.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 3 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
Combination Meter Assembly / GTS Display "Combination Meter"
This ECU uses the CAN communication system for DTC communication.
*: w/ CAN Compatible Optional Devices
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U010087 | Lost Communication with ECM/PCM "A" Missing Message | The combination meter assembly does not receive data from the ECM for approximately 4 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximately 3 seconds or more elapse. ·
The power source voltage of the combination meter assembly is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 7 seconds. | MIL illuminates. | - | DTC is stored until it is cleared using the GTS. |
| U012987 | Lost Communication with Brake System Control Module Missing Message | The combination meter assembly does not receive data from the brake booster with master cylinder assembly for approximately 4 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximately 3 seconds or more elapse. ·
The power source voltage of the combination meter assembly is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 7 seconds. | ·
Brake warning light / red (malfunction) illuminates. ·
Slip indicator light illuminates. ·
ABS warning light illuminates. |
- | DTC is stored until it is cleared using the GTS. |
| U013187 | Lost Communication with Power Steering Control Module Missing Message | The combination meter assembly does not receive data from the rack and pinion power steering gear assembly for approximately 4 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximately 3 seconds or more elapse. ·
The power source voltage of the combination meter assembly is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 7 seconds. | EPS warning light illuminates. | - | DTC is stored until it is cleared using the GTS. |
| U014287 | Lost Communication with Body Control Module "B" Missing Message | The combination meter assembly does not receive data from the main body ECU (multiplex network body ECU) for approximately 5 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximately 3 seconds or more elapse. ·
The power source voltage of the combination meter assembly is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 8 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U015187 | Lost Communication with Restraints Control Module Missing Message | The combination meter assembly does not receive data from the airbag sensor assembly for approximately 5 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected. ·
The power source voltage of the combination meter assembly is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 5 seconds. | SRS warning light illuminates. | - | DTC is stored until it is cleared using the GTS. |
| U016387 | Lost Communication with Navigation Control Module Missing Message | The combination meter assembly does not receive data from the radio and display receiver assembly for approximately 5 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected. ·
The power source voltage of the combination meter assembly is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 5 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U016487 | Lost Communication with HVAC Control Module Missing Message | The combination meter assembly does not receive data from the air conditioning amplifier assembly for approximately 5 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximately 3 seconds or more elapse. ·
The power source voltage of the combination meter assembly is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 8 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U018287 | Lost Communication with Lighting Control Module Front | The combination meter assembly does not receive data from the headlight ECU sub-assembly LH for approximately 5 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximately 3 seconds or more elapse. ·
The power source voltage of the combination meter assembly is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 8 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U023387 | Lost Communication with Side Obstacle Detection Control Module "B" Missing Message | The combination meter assembly does not receive data from the blind spot monitor sensor RH for approximately 5 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximately 3 seconds or more elapse. ·
The power source voltage of the combination meter assembly is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 8 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U023587 | Lost Communication with Cruise Control Front Distance Range Sensor Missing Message | The combination meter assembly does not receive data from the millimeter wave radar sensor assembly for approximately 5 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximately 3 seconds or more elapse. ·
The power source voltage of the combination meter assembly is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 8 seconds. | PCS warning light illuminates. | - | DTC is stored until it is cleared using the GTS. |
| U023A87 | Lost Communication with Image Processing Module "A" Missing Message | The combination meter assembly does not receive data from the forward recognition camera or millimeter wave radar sensor assembly for approximately 5 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected. ·
The power source voltage of the combination meter assembly is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 5 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U029387 | Lost Communication with Hybrid/EV Powertrain Vehicle Control System Missing Message | The combination meter assembly does not receive data from the hybrid vehicle control ECU assembly for approximately 4 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximately 3 seconds or more elapse. ·
The power source voltage of the combination meter assembly is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 7 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U032787 | Software Incompatibility with Vehicle Security Control Module Missing Message | The combination meter assembly does not receive data from the certification ECU (smart key ECU assembly) for approximately 5 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximately 3 seconds or more elapse. ·
The power source voltage of the combination meter assembly is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 8 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U110687 | Lost Communication with Electric Parking Brake Module Missing Message | The combination meter assembly does not receive data from the brake actuator assembly for approximately 4 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximately 3 seconds or more elapse. ·
The power source voltage of the combination meter assembly is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 7 seconds. | Parking brake warning light illuminates. | - | DTC is stored until it is cleared using the GTS. |
| U111087 | Lost Communication with Intuitive Parking Assist Module Missing Message | The combination meter assembly does not receive data from the clearance warning ECU assembly for approximately 5 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximately 3 seconds or more elapse. ·
The power source voltage of the combination meter assembly is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 8 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U111287 | Lost Communication with Combination Switch Module Missing Message | The combination meter assembly does not receive data from the steering sensor for approximately 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximately 3 seconds or more elapse. ·
The power source voltage of the combination meter assembly is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 13 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U111787* | Lost Communication with Accessory Gateway Missing Message | The combination meter assembly does not receive data from the option connector (bus buffer ECU) for approximately 5 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximately 3 seconds or more elapse. ·
The power source voltage of the combination meter assembly is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 8 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U113387 | Lost Communication with PMN Module Missing Message | The combination meter assembly does not receive data from the certification ECU (smart key ECU assembly) for approximately 4 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximately 3 seconds or more elapse. ·
The power source voltage of the combination meter assembly is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 7 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
Air Conditioning Amplifier Assembly / GTS Display "Air Conditioner"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U0100 | Lost Communication With ECM/PCM "A" | The air conditioning amplifier assembly does not receive data from the ECM for approximately 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the air conditioning amplifier assembly is 10 V or more. |
Turn the power switch on (IG) and wait for at least approximately 10 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0131 | Lost Communication With Power Steering Control Module | The air conditioning amplifier assembly does not receive data from the rack and pinion power steering gear assembly for approximately 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the air conditioning amplifier assembly is 10 V or more. |
Turn the power switch on (IG) and wait for at least approximately 10 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication With Body Control Module "B" | The air conditioning amplifier assembly does not receive data from the main body ECU (multiplex network body ECU) for approximately 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the air conditioning amplifier assembly is 10 V or more. |
Turn the power switch on (IG) and wait for at least approximately 10 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0151 | Lost Communication With Restraints Control Module | The air conditioning amplifier assembly does not receive data from the airbag sensor assembly for approximately 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the air conditioning amplifier assembly is 10 V or more. |
Turn the power switch on (IG) and wait for at least approximately 10 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Lost Communication With Instrument Panel Cluster (IPC) Control Module | The air conditioning amplifier assembly does not receive data from the combination meter assembly for approximately 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the air conditioning amplifier assembly is 10 V or more. |
Turn the power switch on (IG) and wait for at least approximately 10 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0163 | Lost Communication With Navigation Control Module | The air conditioning amplifier assembly does not receive data from the radio and display receiver assembly for approximately 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the air conditioning amplifier assembly is 10 V or more. |
Turn the power switch on (IG) and wait for at least approximately 10 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0293 | Lost Communication With HV ECU | The air conditioning amplifier assembly does not receive data from the ECM or hybrid vehicle control ECU assembly for approximately 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the air conditioning amplifier assembly is 10 V or more. |
Turn the power switch on (IG) and wait for at least approximately 10 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
Meter Mirror Sub-assembly / GTS Display "Head Up Display"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U010087 | Lost Communication with ECM/PCM "A" Missing Message | The meter mirror sub-assembly does not receive data from the ECM for approximately 4 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the meter mirror sub-assembly is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 7 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U012987 | Lost Communication with Brake System Control Module Missing Message | The meter mirror sub-assembly does not receive data from the brake booster with master cylinder assembly for approximately 4 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the meter mirror sub-assembly is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 7 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U014287 | Lost Communication with Body Control Module "B" Missing Message | The meter mirror sub-assembly does not receive data from the main body ECU (multiplex network body ECU) for approximately 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the meter mirror sub-assembly is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 8 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U015587 | Lost Communication with Instrument Panel Cluster (IPC) Control Module Missing Message | The meter mirror sub-assembly does not receive data from the combination meter assembly for approximately 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the meter mirror sub-assembly is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 8 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U016387 | Lost Communication with Navigation Control Module Missing Message | The meter mirror sub-assembly does not receive data from the radio and display receiver assembly for approximately 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the meter mirror sub-assembly is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 8 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U016487 | Lost Communication with HVAC Control Module Missing Message | The meter mirror sub-assembly does not receive data from the air conditioning amplifier assembly for approximately 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the meter mirror sub-assembly is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 8 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U023587 | Lost Communication with Cruise Control Front Distance Range Sensor Missing Message | The meter mirror sub-assembly does not receive data from the millimeter wave radar sensor assembly for approximately 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the meter mirror sub-assembly is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 8 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U023A87 | Lost Communication with Image Processing Module "A" Missing Message | The meter mirror sub-assembly does not receive data from the forward recognition camera for approximately 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the meter mirror sub-assembly is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 8 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U029387 | Lost Communication with Hybrid/EV Powertrain Control Module Missing Message | The meter mirror sub-assembly does not receive data from the hybrid vehicle control ECU assembly for approximately 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the meter mirror sub-assembly is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 8 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U111087 | Lost Communication with Intuitive Parking Assist Module Missing Message | The meter mirror sub-assembly does not receive data from the clearance warning ECU assembly for approximately 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the meter mirror sub-assembly is 10.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 8 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
Hybrid Vehicle Control ECU Assembly (w/ Cruise Control System) / GTS Display "Cruise Control"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U012287 | Lost Communication with Vehicle Dynamics Control Module Missing Message | The hybrid vehicle control ECU assembly does not receive data from the brake booster with master cylinder assembly for approximately 3 seconds or more. | All conditions are met:
·
The power switch is on (IG) for approximately 1 second or more. ·
The cruise control main switch is on. ·
The power source voltage of the hybrid vehicle control ECU assembly is 10.5 V or more. |
Turn the cruise control main switch on and wait for at least approximately 4 seconds. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
Hybrid Vehicle Control ECU Assembly (w/ Dynamic Radar Cruise Control System) / GTS Display "Radar Cruise1"
This ECU uses the CAN communication system for DTC communication.
*1: w/ Full-speed Range Following Function
*2: w/o Full-speed Range Following Function
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U010487 | Lost Communication with Cruise Control Module Missing Message | The hybrid vehicle control ECU assembly does not receive data from the millimeter wave radar sensor assembly for approximately 2 seconds or more. | All conditions are met:
·
The power switch is on (IG) for approximately 1 second or more. ·
The cruise control main switch is on. ·
The power source voltage of the hybrid vehicle control ECU assembly is 10.5 V or more. |
Turn the cruise control main switch on and wait for at least approximately 3 seconds. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U012287 | Lost Communication with Vehicle Dynamics Control Module Missing Message | The hybrid vehicle control ECU assembly does not receive data from the brake booster with master cylinder assembly for approximately 3 seconds or more. | All conditions are met:
·
The power switch is on (IG) for approximately 1 second or more. ·
The cruise control main switch is on. ·
The power source voltage of the hybrid vehicle control ECU assembly is 10.5 V or more. |
Turn the cruise control main switch on and wait for at least approximately 4 seconds. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U029387 | Lost Communication with Hybrid Powertrain Control Module Missing Message | The brake booster with master cylinder assembly does not receive data from the hybrid vehicle control ECU assembly for approximately 1 second or more. | All conditions are met:
·
The power switch is on (IG) for approximately 1 second or more. ·
The cruise control main switch is on. ·
Vehicle speed is 5 km/h (3 mph) or more.*1 ·
Vehicle speed is 36 km/h (22 mph) or more.*2 ·
The power source voltage of the hybrid vehicle control ECU assembly is 10.5 V or more. |
·
Drive the vehicle at a speed of 5 km/h (3 mph) or more with the cruise control main switch on for approximately 2 seconds or more.*1 ·
Drive the vehicle at a speed of 36 km/h (22 mph) or more with the cruise control main switch on for approximately 2 seconds or more.*2 |
- | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
Millimeter Wave Radar Sensor Assembly / GTS Display "Radar Cruise2"
This ECU uses the CAN communication system for DTC communication.
*1: w/ Full-speed Range Following Function
*2: w/o Full-speed Range Following Function
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U0125 | Lost Communication with Yaw Rate Sensor Module | The millimeter wave radar sensor assembly does not receive data from the airbag sensor assembly for approximately 1 second or more. | All conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The cruise control main switch is on. ·
Vehicle speed is 5 km/h (3 mph) or more.*1 ·
Vehicle speed is 36 km/h (22 mph) or more.*2 ·
The power source voltage of the millimeter wave radar sensor assembly is 10 V or more. |
·
Drive the vehicle at a speed of 5 km/h (3 mph) or more with the cruise control main switch on for approximately 4 seconds or more.*1 ·
Drive the vehicle at a speed of 36 km/h (22 mph) or more with the cruise control main switch on for approximately 4 seconds or more.*2 |
- | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0126 | Lost Communication with Steering Angle Sensor Module | The millimeter wave radar sensor assembly does not receive data from the steering sensor for approximately 6 seconds or more. | All conditions are met:
·
The power switch is on (IG) for approximately 1 second or more. ·
The cruise control main switch is on. ·
Vehicle speed is 5 km/h (3 mph) or more.*1 ·
Vehicle speed is 36 km/h (22 mph) or more.*2 ·
The power source voltage of the millimeter wave radar sensor assembly is 10 V or more. |
·
Drive the vehicle at a speed of 5 km/h (3 mph) or more with the cruise control main switch on for approximately 7 seconds or more.*1 ·
Drive the vehicle at a speed of 36 km/h (22 mph) or more with the cruise control main switch on for approximately 7 seconds or more.*2 |
- | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The millimeter wave radar sensor assembly does not receive data from the brake booster with master cylinder assembly for approximately 2 seconds or more. | All conditions are met:
·
The power switch is on (IG) for approximately 2 seconds or more. ·
The cruise control main switch is on. ·
Vehicle speed is 5 km/h (3 mph) or more.*1 ·
Vehicle speed is 36 km/h (22 mph) or more.*2 ·
The power source voltage of the millimeter wave radar sensor assembly is 10 V or more. |
·
Drive the vehicle at a speed of 5 km/h (3 mph) or more with the cruise control main switch on for approximately 4 seconds or more.*1 ·
Drive the vehicle at a speed of 36 km/h (22 mph) or more with the cruise control main switch on for approximately 4 seconds or more.*2 |
- | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0293 | Lost Communication with Hybrid Vehicle Control System | The millimeter wave radar sensor assembly does not receive data from the hybrid vehicle control ECU assembly for approximately 1 second or more. | All conditions are met:
·
The power switch is on (IG) for approximately 1 second or more. ·
The cruise control main switch is on. ·
Vehicle speed is 5 km/h (3 mph) or more.*1 ·
Vehicle speed is 36 km/h (22 mph) or more.*2 ·
The power source voltage of the millimeter wave radar sensor assembly is 10 V or more. |
·
Drive the vehicle at a speed of 5 km/h (3 mph) or more with the cruise control main switch on for approximately 2 seconds or more.*1 ·
Drive the vehicle at a speed of 36 km/h (22 mph) or more with the cruise control main switch on for approximately 2 seconds or more.*2 |
- | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
Millimeter Wave Radar Sensor Assembly / GTS Display "Pre-Collision 2"
This ECU uses the CAN communication system for DTC communication.
*: Refer to Pre-Collision System.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>TERMINALS OF ECU
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U0125 | Lost Communication with Yaw Rate Sensor Module | The millimeter wave radar sensor assembly does not receive data from the airbag sensor assembly for approximately 1 second or more. | All conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
Vehicle speed is 5 km/h (3 mph) or more. ·
The power source voltage of the millimeter wave radar sensor assembly is 10 V or more. |
Drive the vehicle at a speed of 5 km/h (3 mph) or more for approximately 4 seconds or more. | PCS warning light blinks. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0126 | Lost Communication with Steering Angle Sensor Module | The millimeter wave radar sensor assembly does not receive data from the steering sensor for approximately 4 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the millimeter wave radar sensor assembly is 10 V or more. |
Turn the power switch on (IG) and wait for at least approximately 7 seconds. | PCS warning light blinks. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The millimeter wave radar sensor assembly does not receive data from the brake booster with master cylinder assembly for approximately 6 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the millimeter wave radar sensor assembly is 10 V or more. |
Turn the power switch on (IG) and wait for at least approximately 9 seconds. | PCS warning light blinks. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0155 | Lost Communication with Instrument Panel Cluster (IPC) Control Module | The millimeter wave radar sensor assembly does not receive data from the combination meter assembly for approximately 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the millimeter wave radar sensor assembly is 10 V or more. |
Turn the power switch on (IG) and wait for at least approximately 8 seconds. | PCS warning light blinks. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0235* | Lost Communication with Cruise Control Front Distance Range Sensor | The brake booster with master cylinder assembly does not receive data from the millimeter wave radar sensor assembly for approximately 2 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 2 seconds or more. ·
The power source voltage of the millimeter wave radar sensor assembly is 10 V or more. |
Turn the power switch on (IG) and wait for at least approximately 4 seconds. | PCS warning light blinks. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U023A* | Lost Communication with Image Processing Module "A" | The millimeter wave radar sensor assembly does not receive data from the forward recognition camera for approximately 1 second or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the millimeter wave radar sensor assembly is 10 V or more. |
Turn the power switch on (IG) and wait for at least approximately 4 seconds. | PCS warning light blinks. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0293 | Lost Communication with Hybrid Vehicle Control System | The millimeter wave radar sensor assembly does not receive data from the hybrid vehicle control ECU assembly for approximately 4 seconds or more. | All conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
Vehicle speed is 5 km/h (3 mph) or more. ·
The power source voltage of the millimeter wave radar sensor assembly is 10 V or more. |
Drive the vehicle at a speed of 5 km/h (3 mph) or more for approximately 7 seconds or more. | PCS warning light blinks. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U1002* | Lost Communication with Gateway Module | The millimeter wave radar sensor assembly does not receive data from the forward recognition camera for approximately 1 second or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the millimeter wave radar sensor assembly is 10 V or more. |
Turn the power switch on (IG) and wait for at least approximately 4 seconds. | PCS warning light blinks. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
Forward Recognition Camera / GTS Display "LKA/LDA"
This ECU uses the CAN communication system for DTC communication.
*: Refer to Lane Departure Alert System.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U0123 | Lost Communication with Yaw Rate Sensor Module | The forward recognition camera does not receive data from the airbag sensor assembly for approximately 5 seconds or more. | All conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
Vehicle speed is 5 km/h (3 mph) or more. ·
The power source voltage of the forward recognition camera is 10 V or more. |
Drive the vehicle at a speed of 5 km/h (3 mph) or more for approximately 8 seconds or more. | Lane departure alert indicator (yellow) illuminates. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0126 | Lost Communication with Steering Angle Sensor Module | The forward recognition camera does not receive data from the steering sensor for approximately 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the forward recognition camera is 10 V or more. |
Turn the power switch on (IG) and wait for at least approximately 8 seconds. | Lane departure alert indicator (yellow) illuminates. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The forward recognition camera does not receive data from the brake booster with master cylinder assembly for approximately 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the forward recognition camera is 10 V or more. |
Turn the power switch on (IG) and wait for at least approximately 8 seconds. | Lane departure alert indicator (yellow) illuminates. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0131 | Lost Communication with Power Steering Control Module | The forward recognition camera does not receive data from the rack and pinion power steering gear assembly for approximately 5 seconds or more. | All conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
Vehicle speed is 5 km/h (3 mph) or more. ·
The power source voltage of the forward recognition camera is 10 V or more. |
Drive the vehicle at a speed of 5 km/h (3 mph) or more for approximately 8 seconds or more. | Lane departure alert indicator (yellow) illuminates. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Body Control Module "B" | The forward recognition camera does not receive data from the main body ECU (multiplex network body ECU) for approximately 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the forward recognition camera is 10 V or more. |
Turn the power switch on (IG) and wait for at least approximately 8 seconds. | Lane departure alert indicator (yellow) illuminates. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0155 | Lost Communication with Instrument Panel Cluster (IPC) Control Module (Combination Meter) | The forward recognition camera does not receive data from the combination meter assembly for approximately 50 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the forward recognition camera is 10 V or more. |
Turn the power switch on (IG) and wait for at least approximately 53 seconds. | Lane departure alert indicator (yellow) illuminates. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0235* | Lost Communication with Cruise Control Front Distance Range Sensor | The forward recognition camera does not receive data from the millimeter wave radar sensor assembly for approximately 5 seconds or more. | All conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
Vehicle speed is 5 km/h (3 mph) or more. ·
The power source voltage of the forward recognition camera is 10 V or more. |
Drive the vehicle at a speed of 5 km/h (3 mph) or more for approximately 8 seconds or more. | Lane departure alert indicator (yellow) illuminates. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U023A* | Lost Communication with Image Processing Module "A" | The rack and pinion power steering gear assembly does not receive data from the forward recognition camera for approximately 5 seconds or more. | All conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
Vehicle speed is 5 km/h (3 mph) or more. ·
The power source voltage of the forward recognition camera is 10 V or more. |
Drive the vehicle at a speed of 5 km/h (3 mph) or more for approximately 8 seconds or more. | Lane departure alert indicator (yellow) illuminates. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0293 | Lost Communication with Hybrid Vehicle Control System | The forward recognition camera does not receive data from the hybrid vehicle control ECU assembly for approximately 5 seconds or more. | All conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
Vehicle speed is 5 km/h (3 mph) or more. ·
The power source voltage of the forward recognition camera is 10 V or more. |
Drive the vehicle at a speed of 5 km/h (3 mph) or more for approximately 8 seconds or more. | Lane departure alert indicator (yellow) illuminates. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
Forward Recognition Camera / GTS Display "Front Recognition Camera"
This ECU uses the CAN communication system for DTC communication.
*: Refer to Forward Recognition Camera System.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U0101 | Lost Communication with TCM | The forward recognition camera does not receive data from the hybrid vehicle control ECU assembly for approximately 5 seconds or more. | All conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
Vehicle speed is 1 km/h or 1 mph or more. ·
The power source voltage of the forward recognition camera is 10 V or more. |
Drive the vehicle at a speed of 1 km/h or 1 mph or more for approximately 8 seconds or more. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0123 | Lost Communication with Yaw Rate Sensor Module | The forward recognition camera does not receive data from the airbag sensor assembly for approximately 5 seconds or more. | All conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
Vehicle speed is 1 km/h or 1 mph or more. ·
The power source voltage of the forward recognition camera is 10 V or more. |
Drive the vehicle at a speed of 1 km/h or 1 mph or more for approximately 8 seconds or more. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0126 | Lost Communication with Steering Angle Sensor Module | The forward recognition camera does not receive data from the steering sensor for approximately 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the forward recognition camera is 10 V or more. |
Turn the power switch on (IG) and wait for at least approximately 8 seconds. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The forward recognition camera does not receive data from the brake booster with master cylinder assembly for approximately 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the forward recognition camera is 10 V or more. |
Turn the power switch on (IG) and wait for at least approximately 8 seconds. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0131 | Lost Communication with Power Steering Control Module | The forward recognition camera does not receive data from the rack and pinion power steering gear assembly for approximately 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the forward recognition camera is 10 V or more. |
Turn the power switch on (IG) and wait for at least approximately 8 seconds. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Body Control Module "B" | The forward recognition camera does not receive data from the main body ECU (multiplex network body ECU) for approximately 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the forward recognition camera is 10 V or more. |
Turn the power switch on (IG) and wait for at least approximately 8 seconds. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0155 | Lost Communication with Instrument Panel Cluster (IPC) Control Module | The forward recognition camera does not receive data from the combination meter assembly for approximately 50 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the forward recognition camera is 10 V or more. |
Turn the power switch on (IG) and wait for at least approximately 53 seconds. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0235* | Lost Communication with Cruise Control Front Distance Range Sensor | The forward recognition camera does not receive data from the millimeter wave radar sensor assembly for approximately 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the forward recognition camera is 10 V or more. |
Turn the power switch on (IG) and wait for at least approximately 8 seconds. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U023A* | Lost Communication with Image Processing Module "A" | The rack and pinion power steering gear assembly does not receive data from the forward recognition camera for approximately 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the forward recognition camera is 10 V or more. |
Turn the power switch on (IG) and wait for at least approximately 8 seconds. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0293 | Lost Communication with Hybrid Vehicle Control System | The forward recognition camera does not receive data from the hybrid vehicle control ECU assembly for approximately 5 seconds or more. | All conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
Vehicle speed is 1 km/h or 1 mph or more. ·
The power source voltage of the forward recognition camera is 10 V or more. |
Drive the vehicle at a speed of 1 km/h or 1 mph or more for approximately 8 seconds or more. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
Clearance Warning ECU Assembly / GTS Display "IPA/ICS/Clearance Sonar"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U0100 | Lost Communication with ECM/TCM "A" | The clearance warning ECU assembly does not receive data from the hybrid vehicle control ECU assembly for approximately 4 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 5 seconds or more. ·
The power source voltage of the clearance warning ECU assembly is 10.2 V or more. |
Turn the power switch on (IG) and wait for at least approximately 9 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0101 | Lost Communication with TCM | The clearance warning ECU assembly does not receive data from the hybrid vehicle control ECU assembly for approximately 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 5 seconds or more. ·
The power source voltage of the clearance warning ECU assembly is 10.2 V or more. |
Turn the power switch on (IG) and wait for at least approximately 10 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Body Control Module | The clearance warning ECU assembly does not receive data from the main body ECU (multiplex network body ECU) for approximately 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 5 seconds or more. ·
The power source voltage of the clearance warning ECU assembly is 10.2 V or more. |
Turn the power switch on (IG) and wait for at least approximately 10 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Lost Communication With Instrument Panel Cluster (IPC) Control Module | The clearance warning ECU assembly does not receive data from the combination meter assembly for approximately 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 5 seconds or more. ·
The power source voltage of the clearance warning ECU assembly is 10.2 V or more. |
Turn the power switch on (IG) and wait for at least approximately 10 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
Blind Spot Monitor Sensor RH / GTS Display "Blind Spot Monitor Master"
This ECU uses the CAN communication system for DTC communication.
*: Refer to Blind Spot Monitor System.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U0125 | Lost Communication with Yaw Rate Sensor Module | The blind spot monitor sensor RH does not receive data from the airbag sensor assembly for approximately 4 seconds or more. | All conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The blind spot monitor main switch is on. ·
The power source voltage of the blind spot monitor sensor RH is 10 V or more. |
Turn the power switch on (IG), turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch) and wait for at least approximately 7 seconds. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0126 | Lost Communication with Steering Angle Sensor Module | The blind spot monitor sensor RH does not receive data from the steering sensor for approximately 6 seconds or more. | All conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The blind spot monitor main switch is on. ·
The power source voltage of the blind spot monitor sensor RH is 10 V or more. |
Turn the power switch on (IG), turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch) and wait for at least approximately 9 seconds. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The blind spot monitor sensor RH does not receive data from the brake booster with master cylinder assembly for approximately 6 seconds or more. | All conditions are met:
·
The power switch is on (IG) for approximately 2 seconds or more. ·
The blind spot monitor main switch is on. ·
The power source voltage of the blind spot monitor sensor RH is 10 V or more. |
Turn the power switch on (IG), turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch) and wait for at least approximately 8 seconds. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Body Control Module "B" | The blind spot monitor sensor RH does not receive data from the main body ECU (multiplex network body ECU) for approximately 13 seconds or more. | All conditions are met:
·
The power switch is on (IG) for approximately 1 second or more. ·
The blind spot monitor main switch is on. ·
The power source voltage of the blind spot monitor sensor RH is 10 V or more. |
Turn the power switch on (IG), turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch) and wait for at least approximately 14 seconds. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0232* | Lost Communication with Blind Spot Monitor Slave Module | The blind spot monitor sensor RH does not receive data from the blind spot monitor sensor LH for approximately 13 seconds or more. | All conditions are met:
·
The power switch is on (IG) for approximately 1 second or more. ·
The blind spot monitor main switch is on. ·
The power source voltage of the blind spot monitor sensor RH is 10 V or more. |
Turn the power switch on (IG), turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch) and wait for at least approximately 14 seconds. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0233* | Lost Communication with Blind Spot Monitor Master Module | The blind spot monitor sensor LH does not receive data from the blind spot monitor sensor RH for approximately 13 seconds or more. | All conditions are met:
·
The power switch is on (IG) for approximately 1 second or more. ·
The blind spot monitor main switch is on. ·
The power source voltage of the blind spot monitor sensor RH is 10 V or more. |
Turn the power switch on (IG), turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch) and wait for at least approximately 14 seconds. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0293 | Lost Communication with HV ECU | The blind spot monitor sensor RH does not receive data from the hybrid vehicle control ECU assembly for approximately 11 seconds or more. | All conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The blind spot monitor main switch is on. ·
The power source voltage of the blind spot monitor sensor RH is 10 V or more. |
Turn the power switch on (IG), turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch) and wait for at least approximately 14 seconds. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U1331* | Software Incompatibility with Body Control Module "B" | Destination information of the main body ECU (multiplex network body ECU) and blind spot monitor sensor RH do not match. | All conditions are met:
·
The power switch is on (IG) for approximately 1 second or more. ·
The blind spot monitor main switch is on. ·
The power source voltage of the blind spot monitor sensor RH is 10 V or more. |
Turn the power switch on (IG), turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch) and wait for at least approximately 1 second. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
Tire Pressure Warning ECU and Receiver / GTS Display "Tire Pressure Monitor"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U0129 | Lost Communication with Brake System Control Module | The tire pressure warning ECU and receiver does not receive data from the brake booster with master cylinder assembly for approximately 60 seconds or more. | The power switch is on (IG) for approximately 1 second or more. | Turn the power switch on (IG) and wait for at least approximately 61 seconds. | - | - | DTC remains stored only while malfunction is occurring. |
Radio and Display Receiver Assembly / GTS Display "Navigation System"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U0073 | Sending Malfunction (Navigation to APGS) | The radio and display receiver assembly does not send/receive data for approximately 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 10 seconds or more. ·
The power source voltage of the radio and display receiver assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0100 | Engine ECU Communication | The radio and display receiver assembly does not receive data from the ECM for approximately 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 10 seconds or more. ·
The power source voltage of the radio and display receiver assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0129 | VSC(ECB)ECU Communication | The radio and display receiver assembly does not receive data from the brake booster with master cylinder assembly for approximately 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 10 seconds or more. ·
The power source voltage of the radio and display receiver assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0140 | Lost Communication with Body Control Module | The radio and display receiver assembly does not receive data from the main body ECU (multiplex network body ECU) for approximately 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 10 seconds or more. ·
The power source voltage of the radio and display receiver assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Meter ECU Communication | The radio and display receiver assembly does not receive data from the combination meter assembly for approximately 30 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 30 seconds or more. ·
The power source voltage of the radio and display receiver assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 60 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0164 | Air Conditioner ECU Communication | The radio and display receiver assembly does not receive data from the air conditioning amplifier assembly for approximately 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 10 seconds or more. ·
The power source voltage of the radio and display receiver assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0265 | Lost Communication with Image Processing Sensor A | The radio and display receiver assembly does not receive data from the rear television camera assembly for approximately 12 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 12 seconds or more. ·
The power source voltage of the radio and display receiver assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 24 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0293 | HV ECU Communication | The radio and display receiver assembly does not receive data from the hybrid vehicle control ECU assembly for approximately 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 10 seconds or more. ·
The power source voltage of the radio and display receiver assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U1110 | Clearance Sonar ECU Communication | The radio and display receiver assembly does not receive data from the clearance warning ECU assembly for approximately 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 10 seconds or more. ·
The power source voltage of the radio and display receiver assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
Brake Actuator Assembly / GTS Display "Electric Parking Brake"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U0073 | Control Module Communication Bus OFF | The brake actuator assembly does not send/receive data for approximately 2 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the brake actuator assembly is 10 V or more. |
Turn the power switch on (IG) and wait for at least approximately 5 seconds. | Brake warning light / yellow (minor malfunction) illuminates. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0100 | Lost Communication With ECM/PCM "A" | The brake actuator assembly does not receive data from the hybrid vehicle control ECU assembly for approximately 15 seconds or more. | All conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
Vehicle speed is 6 km/h (4 mph) or more. ·
The power source voltage of the brake actuator assembly is 10 V or more. |
Drive the vehicle at a speed of 6 km/h (4 mph) or more for approximately 18 seconds or more. | Brake warning light / yellow (minor malfunction) illuminates. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0124 | Lost Communication With Lateral Acceleration Sensor Module | The brake actuator assembly does not receive data from the airbag sensor assembly for approximately 15 seconds or more. | All conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
Vehicle speed is 6 km/h (4 mph) or more. ·
The power source voltage of the brake actuator assembly is 10 V or more. |
Drive the vehicle at a speed of 6 km/h (4 mph) or more for approximately 18 seconds or more. | Brake warning light / yellow (minor malfunction) illuminates. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication With Brake System Control Module | The brake actuator assembly does not receive data from the brake booster with master cylinder assembly for approximately 15 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
The power source voltage of the brake actuator assembly is 10 V or more. |
Turn the power switch on (IG) and wait for at least approximately 18 seconds. | Brake warning light / yellow (minor malfunction) illuminates. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0293 | Lost Communication With Hybrid Vehicle Control System | The brake actuator assembly does not receive data from the hybrid vehicle control ECU assembly for approximately 15 seconds or more. | All conditions are met:
·
The power switch is on (IG) for approximately 3 seconds or more. ·
Vehicle speed is 6 km/h (4 mph) or more. ·
The power source voltage of the brake actuator assembly is 10 V or more. |
Drive the vehicle at a speed of 6 km/h (4 mph) or more for approximately 18 seconds or more. | Brake warning light / yellow (minor malfunction) illuminates. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
Rear Television Camera Assembly / GTS Display "Parking Assist Camera"
This ECU uses the CAN communication system for DTC communication.
*: The rear television camera assembly stores U1000 if an internal error related to the CAN communication system is detected.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>U1000
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U0100 | Lost Communication with ECM/PCM "A" | The rear television camera assembly does not receive data from the ECM or hybrid vehicle control ECU assembly for approximately 11 seconds or more. | The power switch is on (IG) for approximately 3 seconds or more. | Turn the power switch on (IG) and wait for at least approximately 14 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0126 | Lost Communication with Steering Angle Sensor Module | The rear television camera assembly does not receive data from the steering sensor for approximately 11 seconds or more. | The power switch is on (IG) for approximately 3 seconds or more. | Turn the power switch on (IG) and wait for at least approximately 14 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0140 | Lost Communication with Body Control Module | The rear television camera assembly does not receive data from the main body ECU (multiplex network body ECU) for approximately 11 seconds or more. | The power switch is on (ACC) for approximately 3 seconds or more. | Turn the power switch on (IG) and wait for at least approximately 14 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0163 | Lost Communication with Navigation Control Module | The rear television camera assembly does not receive data from the radio and display receiver assembly for approximately 11 seconds or more. | The power switch is on (ACC) for approximately 3 seconds or more. | Turn the power switch on (IG) and wait for at least approximately 14 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0233 | Lost Communication with Blind Spot Monitor Master Module | The rear television camera assembly does not receive data from the blind spot monitor sensor RH for approximately 11 seconds or more. | The power switch is on (IG) for approximately 3 seconds or more. | Turn the power switch on (IG) and wait for at least approximately 14 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U1000* | CAN Communication Failure(Message Registry) | When the power switch is on (IG), a CAN communication malfunction is detected. | The power switch is on (IG). | Turn the power switch on (IG). | - | - | DTC remains stored only while malfunction is occurring. |
| U1110 | Lost Communication with Intuitive Parking Assist Module | The rear television camera assembly does not receive data from the clearance warning ECU assembly for approximately 11 seconds or more. | The power switch is on (IG) for approximately 3 seconds or more. | Turn the power switch on (IG) and wait for at least approximately 14 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
Multiplex Tilt and Telescopic ECU / GTS Display "Tilt&Telescopic"
This ECU uses the CAN communication system for DTC communication.
*1: for LHD
*2: for RHD
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U014287 | Lost Communication with Body Control Module "B" Missing Message | The multiplex tilt and telescopic ECU does not receive data from the main body ECU (multiplex network body ECU) for approximately 10 seconds or more. | The power source voltage of the multiplex tilt and telescopic ECU is 9 V or more. | Turn the power switch on (IG) and wait for at least approximately 10 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U015587 | Lost Communication with Instrument Panel Cluster (IPC) Control Module Missing Message | The multiplex tilt and telescopic ECU does not receive data from the combination meter assembly for approximately 10 seconds or more. | The power source voltage of the multiplex tilt and telescopic ECU is 9 V or more. | Turn the power switch on (IG) and wait for at least approximately 10 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U020887 | Lost Communication with "Seat Control Module A" Missing Message | ·
The multiplex tilt and telescopic ECU does not receive data from the position control ECU assembly LH for approximately 10 seconds or more.*1 ·
The multiplex tilt and telescopic ECU does not receive data from the position control ECU assembly RH for approximately 10 seconds or more.*2 |
The power source voltage of the multiplex tilt and telescopic ECU is 9 V or more. | Turn the power switch on (IG) and wait for at least approximately 10 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
Outer Mirror Control ECU Assembly (for Driver Side) / GTS Display "Mirror L" (for LHD), "Mirror R" (for RHD)
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U0142 | Lost Communication with Body Control Module "B" | The outer mirror control ECU assembly (for driver side) does not receive data from the main body ECU (multiplex network body ECU) for approximately 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected. ·
The power source voltage of the outer mirror control ECU assembly (for driver side) is 10 V or more. |
Turn the power switch on (IG) and wait for at least approximately 10 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
Outer Mirror Control ECU Assembly (for Front Passenger Side) / GTS Display "Mirror R" (for LHD), "Mirror L" (for RHD)
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U0142 | Lost Communication with Body Control Module "B" | The outer mirror control ECU assembly (for front passenger side) does not receive data from the main body ECU (multiplex network body ECU) for approximately 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected. ·
The power source voltage of the outer mirror control ECU assembly (for front passenger side) is 10 V or more. |
Turn the power switch on (IG) and wait for at least approximately 10 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
Central Gateway ECU (Network Gateway ECU) / GTS Display "Central Gateway"
The central gateway ECU (network gateway ECU) is connected to the CAN communication system, but the central gateway ECU (network gateway ECU) does not store or output CAN communication DTCs.
Steering Sensor / GTS Display "Steering Angle Sensor"
The steering sensor is connected to the CAN communication system, but the steering sensor does not store or output CAN communication DTCs.
Swing Grille Actuator Assembly / GTS Display "Grill Shutter"
The swing grille actuator assembly is connected to the CAN communication system, but the swing grille actuator assembly does not store or output CAN communication DTCs.
Position Control ECU Assembly LH / GTS Display "Driver Seat"
The position control ECU assembly LH is connected to the CAN communication system, but the position control ECU assembly LH does not store or output CAN communication DTCs.
Position Control ECU Assembly RH / GTS Display "Driver Seat"
The position control ECU assembly RH is connected to the CAN communication system, but the position control ECU assembly RH does not store or output CAN communication DTCs.
CAN BUS WAVEFORMS
The following waveforms are measured between terminals CANH and GND, and terminals CANL and GND of the central gateway ECU (network gateway ECU). (Use this as a reference for diagnosis of CAN communication lines.)
When malfunctions in multiple ECUs are suspected based on the CAN bus check and DTCs checked using the GTS, check the resistance of the CAN bus using an ohmmeter first. If no problems are found, check the following waveforms.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
If a waveform is not similar to one of the following 3 patterns (Group 1), then an open in a CAN main bus line, an open in a CAN branch line, or a short between a CAN line (CANH or CANL) and ground is suspected (Group 2).
Wiggle the connector and wire harness to check if the waveform changes.
CAN bus waveforms (Group 1)
Normal waveform
Open in both of the lines (CANH and CANL) of a CAN branch
Waveforms (waveforms shown using dotted lines) are not present from an ECU or sensor connected to a CAN branch with an open circuit in both lines. (Waveforms from other ECUs or sensors are normal.)
Because this waveform is similar to a normal waveform, instead of using the waveform, the malfunctioning part can be narrowed down by performing a CAN bus check.
Short between the CAN bus lines (CANH and CANL)
Waveforms disappear.
If the malfunction is in an ECU, disconnecting the ECU will change the waveform. If the waveform does not change, a malfunction in the wire harness is suspected.
CAN bus waveforms (reference) (Group 2)
The following CAN bus waveforms can be used only as reference. The actual measured waveform may differ significantly depending on the location of the open or short circuit.
Open in a CAN branch line (CANH)
An abnormal waveform is output from an ECU with an open in one of its CAN branch lines. Because this abnormal output interferes with the signals from other ECUs, the output of other ECUs will also appear abnormal.
Narrow down the malfunctioning part by checking DTCs or performing a CAN bus check, or by checking waveform changes when ECUs or sensors are disconnected. The waveform will change to one for an open in both sides of a CAN branch when the ECU or sensor with an open CAN branch line is disconnected.
Open in a CAN branch line (CANL)
An abnormal waveform is output from an ECU with an open in one of its CAN branch lines. Because this abnormal output interferes with the signals from other ECUs, the output of other ECUs will also appear abnormal.
Narrow down the malfunctioning part by checking DTCs or performing a CAN bus check, or by checking waveform changes when ECUs or sensors are disconnected. The waveform will change to one for an open in both sides of a CAN branch when the ECU or sensor with an open CAN branch line is disconnected.
Open in a CAN main bus line (CANH)
Waveforms of ECUs or sensors that are closer to the central gateway ECU (network gateway ECU) than the open part are almost normal.
Waveforms of ECUs or sensors that are on the opposite side of the central gateway ECU (network gateway ECU) from the open part are abnormal.
An open in a CAN main bus line can be confirmed by measuring the resistance between the CANH and CANL terminals of any CAN branch.
Short between a CAN bus line (CANH) and ground
Narrow down the shorted part by checking for waveform changes when disconnecting connectors from the CAN junction connectors or when disconnecting ECUs or sensors.
A short to ground in the CANH line can be confirmed by measuring the resistance between CANH and ground using an ohmmeter.
Short between a CAN bus line (CANL) and ground
Narrow down the shorted part by checking for waveform changes when disconnecting connectors from the CAN junction connectors or when disconnecting ECUs or sensors.
A short to ground in the CANL line can be confirmed by measuring the resistance between CANL and ground using an ohmmeter.
DATA SENDING/RECEIVING TABLE
Data sending/receiving table
If Data List items related to sent/received data are not displayed properly, the part for which communication is interrupted can be determined using the table below.
| Data Content | Data Detected and Sent by | Data Received by | Relevant Data List Item | ||
|---|---|---|---|---|---|
| Can be Checked in the Data List | Cannot be Checked in the Data List | Selected System*4 | Data List Items | ||
| Accelerator position | Hybrid vehicle control ECU assembly | ·
Brake booster with master cylinder assembly ·
Inverter with converter assembly |
·
Brake actuator assembly ·
Forward recognition camera ·
Millimeter wave radar sensor assembly ·
Swing grille actuator assembly ·
Radio and display receiver assembly |
Hybrid Control | Accelerator Position |
| ABS/VSC/TRC | Accelerator Opening Angle % | ||||
| Motor Generator | Accelerator Position | ||||
| Engine speed | ECM | ·
Combination meter assembly ·
Hybrid vehicle control ECU assembly ·
Inverter with converter assembly |
·
Air conditioning amplifier assembly ·
Main body ECU (multiplex network body ECU) ·
Certification ECU (smart key ECU assembly) ·
Airbag sensor assembly ·
Brake actuator assembly ·
Radio and display receiver assembly ·
Brake booster with master cylinder assembly ·
Rack and pinion power steering gear assembly |
Engine | Engine Speed |
| Combination Meter | Engine RPM | ||||
| Hybrid Control | Engine Speed | ||||
| Motor Generator | Engine Speed | ||||
| Engine coolant temperature | ECM | ·
Air conditioning amplifier assembly ·
Combination meter assembly ·
Swing grille actuator assembly ·
Hybrid vehicle control ECU assembly ·
Inverter with converter assembly |
·
Radio and display receiver assembly ·
Brake booster with master cylinder assembly |
Engine | Coolant Temperature |
| Air Conditioner | Engine Coolant Temp | ||||
| Combination Meter | Coolant Temperature | ||||
| Grill Shutter | Engine Coolant Temperature | ||||
| Hybrid Control | Coolant Temperature | ||||
| Motor Generator | Coolant Temperature | ||||
| Vehicle speed | Brake booster with master cylinder assembly | ·
Meter mirror sub-assembly ·
Combination meter assembly ·
Hybrid vehicle control ECU assembly ·
Rack and pinion power steering gear assembly ·
Occupant detection ECU ·
Radio and display receiver assembly ·
Brake actuator assembly ·
Millimeter wave radar sensor assembly |
·
Main body ECU (multiplex network body ECU) ·
Airbag sensor assembly ·
Forward recognition camera |
ABS/VSC/TRC | Vehicle Speed |
| Head Up Display | Vehicle Speed Meter | ||||
| Combination Meter | Vehicle Speed Meter | ||||
| Hybrid Control | Vehicle Speed | ||||
| EMPS | Meter Vehicle Velocity | ||||
| Occupant Detection | VSC Vehicle Speed | ||||
| Navigation System | Vehicle Speed | ||||
| Electric Parking Brake | Vehicle Speed | ||||
| Radar Cruise2 | Vhcl Spd-Brake ECU | ||||
| Combination meter assembly*3 | ·
Meter mirror sub-assembly ·
Multiplex tilt and telescopic ECU |
·
Air conditioning amplifier assembly ·
Main body ECU (multiplex network body ECU) ·
Certification ECU (smart key ECU assembly) ·
Clearance warning ECU assembly ·
Position control ECU assembly LH ·
Position control ECU assembly RH |
Combination Meter | Vehicle Speed Meter | |
| Head Up Display | Vehicle Speed from Meter ECU | ||||
| Tilt & Telescopic | Vehicle Speed | ||||
| Wheel speed | Brake booster with master cylinder assembly | ·
Headlight ECU sub-assembly LH ·
Hybrid vehicle control ECU assembly ·
Brake actuator assembly ·
Rack and pinion power steering gear assembly |
·
Airbag sensor assembly ·
Blind spot monitor sensor RH ·
Forward recognition camera ·
Millimeter wave radar sensor assembly ·
Radio and display receiver assembly |
ABS/VSC/TRC | FR Wheel Speed |
| FL Wheel Speed | |||||
| RR Wheel Speed | |||||
| RL Wheel Speed | |||||
| HL AutoLeveling | FR Wheel Speed | ||||
| FL Wheel Speed | |||||
| Hybrid Control | FR Wheel Speed | ||||
| FL Wheel Speed | |||||
| RR Wheel Speed | |||||
| RL Wheel Speed | |||||
| Electric Parking Brake | FR Wheel Speed | ||||
| FL Wheel Speed | |||||
| RR Wheel Speed | |||||
| RL Wheel Speed | |||||
| EMPS | Wheel Speed Right | ||||
| Wheel Speed Left | |||||
| Shift position | Hybrid vehicle control ECU assembly | ·
Certification ECU (smart key ECU assembly) ·
Blind spot monitor sensor RH ·
Brake actuator assembly ·
Radio and display receiver assembly ·
Clearance warning ECU assembly |
·
Main body ECU (multiplex network body ECU) ·
Meter mirror sub-assembly ·
Headlight ECU sub-assembly LH ·
Combination meter assembly*2 ·
Airbag sensor assembly ·
Tire pressure warning ECU and receiver ·
Rear television camera assembly ·
Forward recognition camera ·
Millimeter wave radar sensor assembly ·
Position control ECU assembly LH ·
Position control ECU assembly RH |
Hybrid Control | Shift Position |
| Power Source Control | Shift P Signal | ||||
| Blind Spot Monitor Master | Reverse (Only for AT/CVT) | ||||
| Electric Parking Brake | Shift Position | ||||
| Navigation System | Reverse Signal | ||||
| IPA/ICS/Clearance Sonar | Parking Signal | ||||
| Reverse Signal | |||||
| Ambient temperature | Air conditioning amplifier assembly | ·
Combination meter assembly ·
Meter mirror sub-assembly ·
Brake actuator assembly |
·
Main body ECU (multiplex network body ECU) ·
Rack and pinion power steering gear assembly ·
Forward recognition camera ·
Radio and display receiver assembly ·
Clearance warning ECU assembly |
Air Conditioner | Ambient Temp Sensor |
| Combination Meter | Ambient Temperature (Celsius) | ||||
| Ambient Temperature (Fahrenheit) | |||||
| Head Up Display | Ambient Temperature (Celsius) | ||||
| Ambient Temperature (Fahrenheit) | |||||
| Electric Parking Brake | Ambient Temperature | ||||
| Driver door courtesy switch | Main body ECU (multiplex network body ECU) | - | ·
Certification ECU (smart key ECU assembly) ·
Combination meter assembly*2 ·
Hybrid vehicle control ECU assembly ·
Brake actuator assembly ·
Radio and display receiver assembly |
Main Body | FL Door Courtesy SW |
| Steering angle | Steering sensor | ·
Headlight ECU sub-assembly LH ·
Brake booster with master cylinder assembly ·
Rack and pinion power steering gear assembly ·
Blind spot monitor sensor RH ·
Millimeter wave radar sensor assembly |
·
Main body ECU (multiplex network body ECU) ·
Airbag sensor assembly ·
Rear television camera assembly ·
Forward recognition camera ·
Radio and display receiver assembly ·
Hybrid vehicle control ECU assembly |
HL AutoLeveling | Steering Sensor Signal |
| ABS/VSC/TRC | Steering Angle Sensor | ||||
| EMPS | Steering Angle Velocity | ||||
| Blind Spot Monitor Master | Steering Angle | ||||
| Radar Cruise2 | Steering Angle | ||||
| Yaw rate | Airbag sensor assembly | ·
Brake booster with master cylinder assembly ·
Blind spot monitor sensor RH ·
Millimeter wave radar sensor assembly |
·
Rack and pinion power steering gear assembly ·
Forward recognition camera ·
Radio and display receiver assembly ·
Hybrid vehicle control ECU assembly |
ABS/VSC/TRC | Yaw Rate Sensor |
| Blind Spot Monitor Master | Yaw Rate Sensor | ||||
| Radar Cruise2 | Yaw Rate Sensor | ||||
| Acceleration | Airbag sensor assembly | ·
Brake booster with master cylinder assembly ·
Brake actuator assembly ·
Millimeter wave radar sensor assembly ·
Occupant detection ECU |
·
Rack and pinion power steering gear assembly ·
Forward recognition camera ·
Radio and display receiver assembly ·
Hybrid vehicle control ECU assembly |
ABS/VSC/TRC | Deceleration Sensor |
| Deceleration Sensor2 | |||||
| Electric Parking Brake | Deceleration Sensor 1 | ||||
| Deceleration Sensor 2 | |||||
| Radar Cruise2 | Vehicle Acceleration | ||||
| Occupant Detection | Yaw Rate/G Sensor Invalid Flag1 | ||||
| Yaw Rate/G Sensor Invalid Flag2 | |||||
| Power switch condition | Main body ECU (multiplex network body ECU) | ·
Swing grille actuator assembly ·
Multiplex tilt and telescopic ECU |
·
Meter mirror sub-assembly ·
Certification ECU (smart key ECU assembly) ·
Headlight ECU sub-assembly LH ·
Headlight ECU sub-assembly RH ·
Brake actuator assembly ·
Rear television camera assembly ·
Radio and display receiver assembly ·
Hybrid vehicle control ECU assembly ·
Outer mirror control ECU assembly (for driver side) ·
Outer mirror control ECU assembly (for front passenger side) |
Main Body | IG SW |
| Grill Shutter | IG SW | ||||
| Tilt & Telescopic | Ignition Switch (CAN) | ||||
| Side turn signal | Combination meter assembly | ·
Blind spot monitor sensor RH ·
Forward recognition camera ·
Millimeter wave radar sensor assembly |
·
Main body ECU (multiplex network body ECU) ·
Headlight ECU sub-assembly LH ·
Headlight ECU sub-assembly RH ·
Radio and display receiver assembly |
Combination Meter | Turn Signal Switch (Left) |
| Turn Signal Switch (Right) | |||||
| Blind Spot Monitor Master | Turn Switch State | ||||
| LKA/LDA | Turn Signal Switch (Right) | ||||
| Turn Signal Switch (Left) | |||||
| Pre-Collision 2 | Turn Light RH | ||||
| Turn Light LH | |||||
| ECM power source voltage*1 | ECM | - | - | Engine | BATT Voltage |
| Hybrid vehicle control ECU assembly power source voltage*1 | Hybrid vehicle control ECU assembly | - | - | Hybrid Control | Auxiliary Battery Voltage |
| Combination meter assembly power source voltage*1 | Combination meter assembly | - | - | Combination Meter | +B Voltage |
| Rack and pinion power steering gear assembly power source voltage*1 | Rack and pinion power steering gear assembly | - | - | EMPS | IG Power Supply |
| Driver door touch sensor*1 | Certification ECU (smart key ECU assembly) | - | - | Entry&Start | D-Door Touch Sensor |
| Radio and display receiver assembly power source voltage*1 | Radio and display receiver assembly | - | - | Navigation System | Battery Voltage |
| Brake pedal stroke sensor*1 | Brake booster with master cylinder assembly | - | - | ABS/VSC/TRC | Stroke Sensor |
| Headlight ECU sub-assembly LH power source voltage*1 | Headlight ECU sub-assembly LH | - | - | HL AutoLeveling | +B Voltage Value |
| Meter mirror sub-assembly power source voltage*1 | Meter mirror sub-assembly | - | - | Head Up Display | +B Voltage Value |
| Inverter with converter assembly power source voltage*1 | Inverter with converter assembly | - | - | Motor Generator | Battery Voltage |
| Swing grille actuator assembly power source voltage*1 | Swing grille actuator assembly | - | - | Grill Shutter | +B Power Voltage |
| Multiplex tilt and telescopic ECU power source voltage*1 | Multiplex tilt and telescopic ECU | - | - | Tilt & Telescopic | ECU Power Source Voltage |
*1: Whether the ECU that sends data is functioning or not can be judged by using the GTS to check items such as switches or sensors that send signals to the ECU via direct lines.
*2: Although the received contents cannot be checked in the Data List, whether or not the data is received normally can be checked by observing the combination meter assembly.
*3: The combination meter assembly receives a vehicle speed signal from the skid control ECU and sends the signal to other ECUs.
*4: According to the display on the GTS, read the Data List.
Enter the following menus: Powertrain / Hybrid Control / Data List.
Enter the following menus: Powertrain / Motor Generator / Data List.
Enter the following menus: Powertrain / Engine / Data List.
w/ Canister Pump Module: Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>DATA LIST / ACTIVE TEST
w/o Canister Pump Module: Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>DATA LIST / ACTIVE TEST
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
Enter the following menus: Chassis / EMPS / Data List.
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>DATA LIST / ACTIVE TEST
Enter the following menus: Body Electrical / Combination Meter / Data List.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST
Enter the following menus: Body Electrical / Air Conditioner / Data List.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>DATA LIST / ACTIVE TEST
Enter the following menus: Body Electrical / Navigation System / Data List.
for Audio and Visual System: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DATA LIST / ACTIVE TEST
for Navigation System: Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DATA LIST / ACTIVE TEST
Enter the following menus: Body Electrical / Blind Spot Monitor Master / Data List.
Enter the following menus: Body Electrical / Power Source Control / Data List.
Enter the following menus: Body Electrical / Main Body / Data List.
Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST
Enter the following menus: Chassis / LKA/LDA / Data List.
Enter the following menus: Body Electrical / Occupant Detection / Data List.
Enter the following menus: Powertrain / Radar Cruise2 / Data List.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DATA LIST / ACTIVE TEST
Enter the following menus: Body Electrical / Grille Shutter / Data List.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER SYSTEM>DATA LIST / ACTIVE TEST
Enter the following menus: Chassis / Electric Parking Brake / Data List.
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>DATA LIST / ACTIVE TEST
Enter the following menus: Body Electrical / Entry&Start / Data List.
Enter the following menus: Body Electrical / Pre-Collision 2 / Data List.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DATA LIST / ACTIVE TEST
Enter the following menus: Body Electrical / Head Up Display / Data List.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>HEADUP DISPLAY SYSTEM>DATA LIST / ACTIVE TEST
Enter the following menus: Body Electrical / HL AutoLeveling / Data List.
Enter the following menus: Body Electrical / Tilt & Telescopic / Data List.
Enter the following menus: Body Electrical / IPA/ICS/Clearance Sonar / Data List.