Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM › from 2018.04
RM33C0E _58 Vehicle Interior _065457 LIGHTING (INT) _0330219 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Ambient Illumination Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the instrument panel ambient illumination light (instrument panel light assembly).

WIRING DIAGRAM

E387847E02
3.906,3.385 4.219,3.583 0.313,0.198 10 false 3G 4.323,3.385 4.635,3.583 0.313,0.198 10 false 3F 4.792,3.531 5.375,3.781 0.583,0.25 10 false DOME 2.771,3.531 3.354,3.781 0.583,0.25 10 false DC/DC 0.51,3.354 2.146,3.656 1.635,0.302 10 false from Auxiliary Battery 4.354,3.177 4.667,3.375 0.313,0.198 10 false 1 4.323,2.448 4.635,2.646 0.313,0.198 10 false 24 4.365,3.917 6,4.292 1.635,0.375 10 false Instrument Panel Junction Block Assembly 5.448,5.646 7.115,6.042 1.667,0.396 10 false Main Body ECU (Multiplex Network Body ECU) 4.313,2.646 4.625,2.844 0.313,0.198 10 false 3B 5.698,1.021 6.031,1.25 0.333,0.229 10 false K53 6.115,0.896 6.698,1.146 0.583,0.25 10 false LED1 1.333,1.719 4.01,2.104 2.677,0.385 10 false Instrument Panel Ambient Illumination Light (Instrument Panel Light Assembly) 1.344,1.552 1.677,1.781 0.333,0.229 10 false K89 1.76,0.896 2,1.146 0.24,0.25 10 false B 3.333,0.896 3.573,1.146 0.24,0.25 10 false E 3.958,3.177 4.271,3.375 0.313,0.198 10 false 1 3.604,0.885 3.917,1.083 0.313,0.198 10 false 1 1.521,0.896 1.833,1.094 0.313,0.198 10 false 2 3.917,3.604 4.229,3.802 0.313,0.198 10 false *2 4.313,3.594 4.625,3.792 0.313,0.198 10 false *1 1.854,5.229 2.865,5.479 1.01,0.25 10 false *1: for LHD 1.854,5.552 2.865,5.802 1.01,0.25 10 false *2: for RHD 5.74,0.823 6.052,1.021 0.313,0.198 10 false 20

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Interior Illumination Light1 Instrument panel ambient illumination light (Instrument panel light assembly) OFF or ON Preconditions for using the Active Test to check dimmer controlled illumination:
·

Power switch on (IG)

·

Shift lever is in any position other than P


Body Electrical > Main Body > Active Test
Tester Display
Interior Illumination Light1
50004 123 68
OK:

Instrument panel ambient illumination light comes on.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT INSTRUMENT PANEL LIGHT ASSEMBLY
2.INSPECT INSTRUMENT PANEL LIGHT ASSEMBLY
a.

Remove the instrument panel ambient illumination light (instrument panel light assembly).

Click hereVehicle Interior>LIGHTING (INT)>AMBIENT LIGHT>REMOVAL


b.

Inspect the instrument panel ambient illumination light (instrument panel light assembly).

Click hereVehicle Interior>LIGHTING (INT)>AMBIENT LIGHT>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPLACE INSTRUMENT PANEL AMBIENT ILLUMINATION LIGHT (INSTRUMENT PANEL LIGHT ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3F*1 or 3G*2 instrument panel junction block assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3F-1 - Body ground*1 Power switch off 11 to 14 V
3G-1 - Body ground*2 Power switch off 11 to 14 V


*1: for LHD

*2: for RHD



Result:
Proceed to
OK
NG



OK

4.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E341598C28
2.146,0.927 2.479,1.146 0.333,0.219 5.073,0.854 5.406,1.073 0.333,0.219 5.073,1.156 5.406,1.375 0.333,0.219 2.229,0.948 2.542,1.146 0.313,0.198 10 false 3B 0.271,0.198 0.583,0.396 0.313,0.198 10 false *a 5.156,0.865 5.469,1.063 0.313,0.198 10 false 3F 5.146,1.167 5.458,1.365 0.313,0.198 10 false 3G 5.458,1.177 5.771,1.375 0.313,0.198 10 false *B 5.458,0.875 5.771,1.073 0.313,0.198 10 false *A
*A for LHD *B for RHD
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


a.

Disconnect the 3B instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3B-24 - 3F-1*1 Always Below 1 Ω
3B-24 - 3G-1*2 Always Below 1 Ω


*1: for LHD

*2: for RHD



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - INSTRUMENT PANEL LIGHT ASSEMBLY)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - INSTRUMENT PANEL LIGHT ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3B-24 - K89-2 (B) Always Below 1 Ω
3B-24 or K89-2 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL LIGHT ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL LIGHT ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the K53 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K89-1 (E) - K53-20 (LED1) Always Below 1 Ω
K89-1 (E) or K53-20 (LED1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR