Wear protective gloves. Sharp areas on the parts may injure your hands.
Use the same procedure for RHD and LHD vehicles.
The following procedure is for LHD vehicles.
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
72106B
1.INSTALL UPPER SEAT TRACK RAIL SUB-ASSEMBLY (w/ Vertical Adjuster)
72108
2.INSTALL UPPER SEAT TRACK RAIL SUB-ASSEMBLY (w/o Vertical Adjuster)
85822B
3.INSTALL POWER SEAT TILT MOTOR ASSEMBLY (w/ Vertical Adjuster)
Install the power seat tilt motor assembly with the 3 bolts.
Bolt (A) is shorter than bolt (B). Make sure to install them to the correct positions.
85822C
4.INSTALL POWER SEAT LIFTER MOTOR ASSEMBLY (w/ Vertical Adjuster)
Install the power seat lifter motor assembly.
| *a | Stud Bolt of the Front Seat Vertical Housing Sub-assembly |
| *b | Hole of the Front Seat Adjuster Assembly |
| *c | Front Seat Vertical Housing Sub-assembly |
| *d | Front Seat Adjuster Assembly |
Install the front seat vertical housing sub-assembly.
Make sure to insert the stud bolt of the front seat vertical housing sub-assembly into the hole of the front seat adjuster assembly as shown in the illustration.
Make sure to position the front seat adjuster assembly so that when the front seat vertical housing sub-assembly is installed, their gears will be positioned as shown in the illustration.
Install the vertical adjuster spacer.
Install the front seat adjuster plate with the 3 nuts.
Tighten the nuts in the order shown in the illustration.
71874C
5.INSTALL FRONT SEAT LOWER CUSHION SHIELD (w/ Vertical Adjuster)
|
Install in this Direction |
Engage the guide as shown in the illustration.
Engage the claw to install the front seat lower cushion shield.
7181B
6.INSTALL FRONT SEAT CUSHION WIRE HARNESS HOLDER (w/o Vertical Adjuster)
Engage the claw to install the front seat cushion wire harness holder.
Install the 2 screws.
7181B
7.INSTALL FRONT SEAT CUSHION WIRE HARNESS HOLDER (w/ Vertical Adjuster)
|
Install in this Direction |
Engage the guide as shown in the illustration.
Engage the 2 claws to install the front seat cushion wire harness holder.
Install the 2 screws.
71052A
8.INSTALL FRONT SEAT CUSHION SPRING SUB-ASSEMBLY
Engage the 6 hooks to install the front seat cushion spring sub-assembly to the front seat adjuster assembly.
9.INSTALL FRONT SEAT NO. 3 WIRE (w/ Occupant Classification System)
Engage the claw to install the front seat No. 3 wire.
72277A
10.INSTALL SEAT SLIDE POSITION SENSOR PROTECTOR (w/ Occupant Classification System)
| *a | Pin |
| *b | Engagement Point |
|
Engage in this Direction |
|
Insert in this Direction |
Insert the seat slide position sensor protector as shown in the illustration.
Engage the seat slide position sensor protector to the pin of the seat position airbag sensor as shown in the illustration.
Engage the clamp and connect the connector.
82192
11.INSTALL FRONT SEAT WIRE
Connect each connector and engage each clamp to install the front seat wire.
87501B
12.INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System)
71874A
13.INSTALL FRONT SEAT LOWER CUSHION SHIELD LH (w/ Vertical Adjuster)
| *a | Hook |
| *b | Guide |
Engage the claw and guide to install the front seat lower cushion shield LH.
Engage the hook.
71873U
14.INSTALL FRONT SEAT LOWER CUSHION SHIELD RH (w/ Vertical Adjuster)
| *a | Hook |
| *b | Guide |
Engage the claw and guide to install the front seat lower cushion shield RH.
Engage the hook.
71875G
15.INSTALL LH SEAT RECLINING ADJUSTER INSIDE COVER LH (w/ Vertical Adjuster)
Engage the 4 claws to install the LH seat reclining adjuster inside cover LH.
Engage the claw.
71876G
16.INSTALL LH SEAT RECLINING ADJUSTER INSIDE COVER RH (w/ Vertical Adjuster)
Engage the 4 claws to install the LH seat reclining adjuster inside cover RH.
71876F
17.INSTALL RH SEAT RECLINING ADJUSTER INSIDE COVER LH (w/o Vertical Adjuster)
Engage the 4 claws to install the RH seat reclining adjuster inside cover LH.
71875F
18.INSTALL RH SEAT RECLINING ADJUSTER INSIDE COVER RH (w/o Vertical Adjuster)
Engage the 4 claws to install the RH seat reclining adjuster inside cover RH.
Engage the claw and clamp.
85860A
19.INSTALL SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY (w/ Climate Control Seat System)
Engage the hook.
Install the seat cushion climate control blower assembly with the 2 bolts.
Connect the connector.
w/ Vertical Adjuster:
Engage the wire harness clamp.
87510L
20.INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)
71072S
21.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER
Engage the 14 claws to install the separate type front seat cushion cover to the separate type front seat cushion pad.
22.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD
Engage the 10 hooks to install the separate type front seat cushion cover with pad to the separate type front seat cushion spring assembly.
w/ Seat Heater System:
Engage the clamp.
Connect the connector.
w/ Occupant Detection Sensor:
|
Install in this Direction |
Engage the claw to install the connector holder to the occupant detection sensor wire harness as shown in the illustration.
|
Install in this Direction |
Engage the claw to install the connector holder as shown in the illustration.
8219B
23.INSTALL FRONT SEAT NO. 2 WIRE
Connect each connector and engage each clamp to install the front seat No. 2 wire.
71759D
24.INSTALL FRONT NO. 2 SEATBACK HOOK
Install the 2 front No. 2 seatback hooks to the front seatback frame sub-assembly.
71587
25.INSTALL FRONT SEATBACK EDGE PROTECTOR
w/o Vertical Adjuster:
Install the 2 front seatback edge protectors to the front seatback spring sub-assembly.
w/ Vertical Adjuster:
Install the 2 front seatback edge protectors to the lumbar support adjuster assembly.
72760D
26.INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY (w/ Vertical Adjuster)
71054S
27.INSTALL FRONT SEATBACK SPRING SUB-ASSEMBLY (w/o Vertical Adjuster)
|
Install in this Direction |
Install the front seatback spring sub-assembly to the front seatback frame sub-assembly as shown in the illustration.
Engage the 2 claws to install the 2 front seatback edge protectors to the front seatback frame sub-assembly.
85867
28.INSTALL SEATBACK CLIMATE CONTROL BLOWER (w/ Climate Control Seat System)
| *a | Wire Harness Clamp |
| *b | Hook |
Engage the 2 claws and 2 hooks and install the seatback climate control blower.
Connect the connector and engage the wire harness clamp.
73920A
29.INSTALL FRONT SEAT AIRBAG ASSEMBLY (w/ Front Seat Side Airbag)
87510N
30.INSTALL FRONT SEATBACK HEATER ASSEMBLY (w/ Seat Heater System)
71074S
31.INSTALL SEPARATE TYPE FRONT SEATBACK COVER
Engage the 9 claws to install the separate type front seatback cover to the separate type front seatback pad.
32.INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD
Install the separate type front seatback cover with pad.
71931
33.INSTALL FRONT SEAT HEADREST SUPPORT
Engage the 4 claws to install the 2 front seat headrest supports.
w/o Rear Seat Belt Warning System:
| *1 | Seat Cover Hanger |
| *a | Bracket |
|
Install in this Direction |
Slide the bracket as shown in the illustration to engage the hook and connect the bracket to the seat cover hanger.
For vehicles with a front seat airbag assembly, the separate type front seatback cover with pad must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.
Make sure that the strap is not twisted after connecting the bracket to the seat cover hanger.
Install the bracket securely.
| *1 | Seatback Cover Hook |
| *a | Pin |
Insert the seatback cover hook and push in the pin to install it as shown in the illustration.
|
Install in this Direction |
Engage the hook as shown in the illustration.
Close the 2 fasteners.
w/ Seat Heater System:
Engage the clamp.
Engage the 3 hooks.
34.INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY (w/o Front Seat Side Airbag)
Engage the 4 guides.
Install the separate type front seatback assembly to the separate type front seat cushion assembly with the 4 bolts.
Engage the clamp.
Connect the connector.
Engage the 2 hooks.
Pass the separate type front seatback cover through the grooves of the LH seat reclining adjuster inside cover LH and LH seat reclining adjuster inside cover RH.
35.INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY (w/ Front Seat Side Airbag)
Engage the 4 guides.
Install the separate type front seatback assembly to the separate type front seat cushion assembly with the 4 bolts.
w/ Seat Heater System:
Connect the connector.
Engage the clamp.
Engage the clamp.
Connect the connector.
w/o Vertical Adjuster:
Engage the claw and 4 clamps to install the front seat airbag assembly wire harness.
Engage the claw first.
w/ Vertical Adjuster:
Engage the claw and 4 clamps to install the front seat airbag assembly wire harness.
Engage the claw first.
Engage the 2 hooks.
Pass the separate type front seatback cover through the grooves of the LH seat reclining adjuster inside cover LH and LH seat reclining adjuster inside cover RH.
72136B
36.INSTALL LOWER NO. 3 SEAT TRACK SPACER (for LH Side)
w/ Rear Seat Belt Warning System:
Engage the 2 guides and claw to install the lower No. 3 seat track spacer to the front seat cushion shield.
72136C
37.INSTALL LOWER NO. 4 SEAT TRACK SPACER (for LH Side)
w/ Rear Seat Belt Warning System:
Engage the 2 guides and claw to install the lower No. 4 seat track spacer to the front seat inner cushion shield.
72136A
38.INSTALL LOWER NO. 2 SEAT TRACK SPACER (for RH Side)
w/ Rear Seat Belt Warning System:
Use the same procedure as for the Lower No. 4 Seat Track Spacer (for LH Side).
72136
39.INSTALL LOWER NO. 1 SEAT TRACK SPACER (for RH Side)
w/ Rear Seat Belt Warning System:
Use the same procedure as for the Lower No. 3 Seat Track Spacer (for LH Side).
84922C
40.INSTALL FRONT POWER SEAT SWITCH
72714
41.INSTALL SEAT ADJUSTER SHIELD CLAMP BRACKET (w/ Vertical Adjuster)
Install the seat adjuster shield clamp bracket to the front seat cushion shield with the 2 screws.
84921A
42.INSTALL RECLINING POWER SEAT SWITCH KNOB
Engage the 4 claws to install the reclining power seat switch knob.
84921B
43.INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB
Engage the 4 claws to install the slide and vertical power seat switch knob.
71862
44.INSTALL FRONT SEAT INNER CUSHION SHIELD (w/o Vertical Adjuster)
|
Install in this Direction |
Engage the 2 claws and 2 guides as shown in the illustration.
Engage the 3 claws to install the front seat inner cushion shield.
71812D
45.INSTALL FRONT SEAT CUSHION SHIELD (w/o Vertical Adjuster)
Connect the front power seat switch connector.
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Engage the guide (A) as shown in the illustration.
Engage the 2 claws and 2 guides (B) as shown in the illustration.
Engage the 3 claws to install the front seat cushion shield.
71862
46.INSTALL FRONT SEAT INNER CUSHION SHIELD (w/ Vertical Adjuster)
|
Install in this Direction |
Engage the 2 claws and 2 guides as shown in the illustration.
Engage the 2 claws to install the front seat inner cushion shield.
71812D
47.INSTALL FRONT SEAT CUSHION SHIELD (w/ Vertical Adjuster)
Connect the front power seat switch connector.
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Engage the guide (A) as shown in the illustration.
Engage the 2 claws and 2 guides (B) as shown in the illustration.
Engage the 2 claws to install the front seat cushion shield.
71868N
48.INSTALL FRONT SEAT FRONT CUSHION SHIELD
Engage the 3 guides.
|
Install in this Direction |
Engage the 2 claws as shown in the illustration.
|
Install in this Direction |
Engage the guide as shown in the illustration.
Install the front seat front cushion shield with the clip.
71074S
49.CONNECT SEPARATE TYPE FRONT SEATBACK COVER
Connect the rubber band of the separate type front seatback cover.
73230
50.INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side)
73240
51.INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Driver Side)
89710D
52.INSTALL POSITION CONTROL ECU ASSEMBLY (w/ Seat Position Memory System)