CHECK VEHICLE APPROACHING SPEAKER CONTROLLER
Disconnect the K156 vehicle approaching speaker controller connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| K156-1 (IG) - Body ground | LA-B - Body ground | IG power supply | Power switch on (IG) | 11 to 14 V |
| Power switch off | Below 1 V | |||
| K156-7 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Connect the K156 vehicle approaching speaker controller connector.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| K156-2 (STP) - K156-7 (GND) | LA-L - W-B | Stop light signal input | Power switch off, brake pedal depressed | 8 V or higher |
| Power switch off, brake pedal released | Below 1 V | |||
| K156-3 (SP+) - K156-8 (SP-) | GR - W | Vehicle approaching speaker output | Vehicle approaching speaker operating | A waveform synchronized with the sound is output.
(See Waveform 1) |
| K156-5 (SW) - K156-7 (GND) | LA-R - W-B | Vehicle approaching speaker switch signal input | Power switch on(IG), vehicle approaching speaker switch not pressed | Below 1 V |
| Power switch on(IG), vehicle approaching speaker switch pressed | 6 V or higher | |||
| K156-6 (SPD) - K156-7 (GND) | G - W-B | Speed signal input | Power switch on (IG), wheel being rotated | Pulse generation
(See Waveform 2) |
| K156-9 (PRST) - K156-7 (GND) | LG - W-B | SIL communication signal | Power switch on (IG), during transmission | Pulse generation
(See Waveform 3) |
| K156-10 (IND) - K156-7 (GND) | R - W-B | Warning signal output | Power switch on (IG), vehicle proximity notification off indicator light on | Below 1.8 V |
| Power switch on (IG), vehicle proximity notification off indicator light off | 11 to 14 V | |||
| K156-11 (KOK) - K156-7 (GND) | BE - W-B | Permission signal | Power switch on (READY), shift lever in P | Below 2.3 V |
| Power switch on (READY), engine stopped and shift lever not in P | 8 V or higher |
Waveform 1
| Item | Condition |
|---|---|
| Tester Connection | K156-3 (SP+) - K156-8 (SP-) |
| Tool Setting | 1 V/DIV., 200 ms./DIV. |
| Vehicle Condition | Vehicle approaching speaker operating |
Waveform 2
| Item | Condition |
|---|---|
| Tester Connection | K156-6 (SPD) - K156-7 (GND) |
| Tool Setting | 5 V/DIV., 20 ms./DIV. |
| Vehicle Condition | Power switch on (IG), wheel being rotated |
When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.
Waveform 3
| Item | Condition |
|---|---|
| Tester Connection | K156-9 (PRST) - K156-7 (GND) |
| Tool Setting | 5 V/DIV., 10 ms./DIV. |
| Vehicle Condition | Power switch on (IG), during transmission |
CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY