Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM › 2018.08–2021.02
RM33C0E _54 Brake _065446 PARKING BRAKE _0329402 ELECTRIC PARKING BRAKE SYSTEM C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM  C13A9  Brake System Malfunction  


DESCRIPTION

The parking brake ECU (brake actuator assembly) receives the wheel speed signal of each wheel from the skid control ECU (brake booster with master cylinder assembly) via CAN communication.

This DTC is stored when a malfunction occurs in the skid control ECU (brake booster with master cylinder assembly).

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
C13A9 Brake System Malfunction
Detection conditions (1)
·

Diagnosis Condition:

Power switch on (IG)

·

Malfunction Status:

Abnormal signal received from all speed sensors from skid control ECU (brake booster with master cylinder assembly)

·

Detection Time:

Approximately 0.3 seconds


Detection conditions (2)
·

Diagnosis Condition:

Power switch on (IG)

·

Malfunction Status:

Brake system malfunctioning signal received from skid control ECU (brake booster with master cylinder assembly)

·

Detection Time:

Approximately 0.3 seconds


Detection conditions (3), (4)
·

Diagnosis Condition:

Power switch on (IG), vehicle being driven and parking brake not engaged

·

Malfunction Status:

When parking brake ECU (brake actuator assembly) not outputting parking brake operation request signal, there is parking brake operation signal from skid control ECU (brake booster with master cylinder assembly)

·

Detection Time:

Approximately 0.3 seconds


·

Skid control ECU (brake booster with master cylinder assembly)

·

Parking brake ECU (brake actuator assembly)


DTC stored An electric parking brake system malfunction is displayed on the multi-information display.

DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4
Diagnosis Condition Power switch on (IG) ○ ○ ○ -
Vehicle being driven and parking brake not engaged - - - ○
Malfunction Status Abnormal signal received from all speed sensors from skid control ECU (brake booster with master cylinder assembly) ○ - - -
Brake system malfunctioning signal received from skid control ECU (brake booster with master cylinder assembly) - ○ - -
When parking brake ECU (brake actuator assembly) not outputting parking brake operation request signal, there is parking brake operation signal from skid control ECU (brake booster with master cylinder assembly) - - ○ ○
Detection Time Approximately 0.3 seconds Approximately 0.3 seconds Approximately 0.3 seconds Approximately 0.3 seconds
Number of Trips 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:

The parking brake indicator light blinks (red) when the power switch is turned on (IG) after replacing the parking brake ECU (brake actuator assembly). Operate the electric parking brake switch (electric parking brake switch assembly) to turn off the parking brake indicator light (red).


PROCEDURE

1.CHECK DTC (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)
a.

Check for DTCs.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTCs are not output A
DTCs are output B




A

2.CHECK DTC (ELECTRIC PARKING BRAKE SYSTEM)

B

2.CHECK DTC (ELECTRIC PARKING BRAKE SYSTEM)
a.

Clear the DTCs.

Chassis > Electric Parking Brake > Clear DTCs
50002 184

b.

Turn the power switch off.


c.

Check for DTCs.

Chassis > Electric Parking Brake > Trouble Codes
50001 184

Result:
Result Proceed to
DTCs are output A
DTCs are not output B



A

B