Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2018.08–2022.01
RM33C0E _57 Power Source / Network _065454 NETWORKING _0329710 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check Bus 4 Line for Short to GND  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and GND when there is no resistance between terminal 22 (CA2H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 7 (CA2L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.

Symptom Trouble Area
There is no resistance between terminal 22 (CA2H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 7 (CA2L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.
·

Short to ground in CAN main bus line

·

Short to ground in CAN branch line

·

Central gateway ECU (network gateway ECU)

·

Occupant detection ECU

(w/ Occupant Classification System)

·

Tire pressure warning ECU and receiver

(w/ Tire Pressure Warning System and Tire Inflation Pressure Display Function)

·

Rack and pinion power steering gear assembly

·

Brake booster with master cylinder assembly

·

Steering sensor

·

Airbag sensor assembly

·

ECM

·

Brake actuator assembly

·

Hybrid vehicle control ECU assembly

·

No. 2 CAN junction connector

·

No. 4 CAN junction connector

·

No. 3 junction connector



WIRING DIAGRAM

C381548E02
0.063,1.427 0.375,1.625 0.313,0.198 10 false R9 0.302,1.427 1.698,1.979 1.396,0.552 10 false Tire Pressure Warning ECU and Receiver*1 0.771,0.458 1.271,0.719 0.5,0.26 10 false CANH 0.792,0.99 1.292,1.25 0.5,0.26 10 false CANL 1.313,0.323 1.625,0.521 0.313,0.198 10 false 9 1.281,0.875 1.594,1.073 0.313,0.198 10 false 10 3.104,0.333 3.417,0.531 0.313,0.198 10 false 8 3.031,0.865 3.344,1.063 0.313,0.198 10 false 19 4.021,0.344 4.333,0.542 0.313,0.198 10 false 10 4.021,0.875 4.333,1.073 0.313,0.198 10 false 21 5.563,0.354 5.875,0.552 0.313,0.198 10 false 22 5.635,0.854 5.948,1.052 0.313,0.198 10 false 7 5.854,0.354 6.354,0.615 0.5,0.26 10 false CA2H 5.865,0.885 6.365,1.146 0.5,0.26 10 false CA2L 4.813,1.396 5.313,1.656 0.5,0.26 10 false K76 5.146,1.385 7.104,1.927 1.958,0.542 10 false Central Gateway ECU (Network Gateway ECU) 0.063,3.458 0.375,3.656 0.313,0.198 10 false a6 0.281,3.469 2.188,3.813 1.906,0.344 10 false Occupant Detection ECU*2 0.802,2.49 1.302,2.75 0.5,0.26 10 false CANP 0.781,3.031 1.281,3.292 0.5,0.26 10 false CANN 1.281,2.375 1.594,2.573 0.313,0.198 10 false 5 1.302,2.906 1.615,3.104 0.313,0.198 10 false 4 3.01,2.917 3.323,3.115 0.313,0.198 10 false 20 3.083,2.375 3.396,2.573 0.313,0.198 10 false 9 2.625,3.354 2.979,3.552 0.354,0.198 10 false R99 2.958,3.354 4.573,3.729 1.615,0.375 10 false No. 3 Junction Connector 5.198,2.542 6.969,3.49 1.771,0.948 10 false *1: w/ Tire Pressure Warning System and Tire Inflation Pressure Display Function 5.177,3.792 7.052,4.417 1.875,0.625 10 false *2: w/ Occupant Classification System 0.073,5.656 0.385,5.854 0.313,0.198 10 false A40 0.385,5.656 2.052,6.24 1.667,0.583 10 false Brake Booster with Master Cylinder Assembly 0.802,4.708 1.302,4.969 0.5,0.26 10 false CA1H 0.813,5.229 1.313,5.49 0.5,0.26 10 false CA1L 4.021,2.927 4.333,3.125 0.313,0.198 10 false 22 4.021,2.365 4.333,2.563 0.313,0.198 10 false 11 4.01,4.563 4.323,4.76 0.313,0.198 10 false 2 3.99,5.094 4.302,5.292 0.313,0.198 10 false 13 3.063,4.563 3.375,4.76 0.313,0.198 10 false 1 3.01,5.104 3.323,5.302 0.313,0.198 10 false 12 4.021,5.906 4.333,6.104 0.313,0.198 10 false 3 4.01,6.448 4.323,6.646 0.313,0.198 10 false 14 3.063,6.75 3.375,6.948 0.313,0.198 10 false 6 3.021,7.271 3.333,7.469 0.313,0.198 10 false 17 5.771,5.906 6.083,6.104 0.313,0.198 10 false 7 5.719,6.438 6.031,6.635 0.313,0.198 10 false 17 6,6.021 6.5,6.281 0.5,0.26 10 false CAN+ 6.01,6.552 6.51,6.813 0.5,0.26 10 false CAN- 6.063,6.948 6.563,7.208 0.5,0.26 10 false A22 6.375,6.948 6.875,7.208 0.5,0.26 10 false ECM 2.583,8.156 3,8.365 0.417,0.208 10 false A67 0.063,7.823 0.375,8.021 0.313,0.198 10 false A44 0.375,7.833 2.042,8.417 1.667,0.583 10 false Brake Actuator Assembly 0.781,6.875 1.281,7.135 0.5,0.26 10 false CANH 0.813,7.406 1.313,7.667 0.5,0.26 10 false CANL 1.292,4.583 1.604,4.781 0.313,0.198 10 false 43 1.292,5.125 1.604,5.323 0.313,0.198 10 false 42 1.292,6.74 1.604,6.938 0.313,0.198 10 false 12 1.281,7.292 1.594,7.49 0.313,0.198 10 false 11 2.896,8.167 4.99,8.49 2.094,0.323 10 false No. 2 CAN Junction Connector 6.375,0.698 6.875,0.958 0.5,0.26 10 false 120 Ω

C381549E01
2.615,1.469 3.073,1.667 0.458,0.198 10 false A67 2.927,1.469 4.167,2.073 1.24,0.604 10 false No. 2 CAN Junction Connector 3.052,0.438 3.51,0.635 0.458,0.198 10 false 5 2.979,0.958 3.438,1.156 0.458,0.198 10 false 16 4,0.427 4.458,0.625 0.458,0.198 10 false 4 3.969,0.958 4.427,1.156 0.458,0.198 10 false 15 5.708,0.427 6.167,0.625 0.458,0.198 10 false 10 5.698,0.938 6.156,1.135 0.458,0.198 10 false 11 5.979,0.531 6.438,0.729 0.458,0.198 10 false CANH 4.781,1.479 5.24,1.677 0.458,0.198 10 false C71 5.104,1.479 7.104,2.135 2,0.656 10 false Rack and Pinion Power Steering Gear Assembly 5.979,1.063 6.438,1.26 0.458,0.198 10 false CANL 2.813,2.771 3.271,2.969 0.458,0.198 10 false K127 2.813,3.302 3.271,3.5 0.458,0.198 10 false K127 3.99,2.771 4.448,2.969 0.458,0.198 10 false K127 3.99,3.292 4.448,3.49 0.458,0.198 10 false K127 3.979,4.833 4.438,5.031 0.458,0.198 10 false K128 3.99,5.365 4.448,5.563 0.458,0.198 10 false K128 2.813,4.833 3.271,5.031 0.458,0.198 10 false K128 2.802,5.365 3.26,5.563 0.458,0.198 10 false K128 2.948,2.542 3.406,2.74 0.458,0.198 10 false 6 2.906,3.094 3.365,3.292 0.458,0.198 10 false 17 4.115,2.542 4.573,2.74 0.458,0.198 10 false 7 4.073,3.104 4.531,3.302 0.458,0.198 10 false 18 4.104,4.604 4.563,4.802 0.458,0.198 10 false 5 4.063,5.156 4.521,5.354 0.458,0.198 10 false 16 2.927,4.615 3.385,4.813 0.458,0.198 10 false 6 2.906,5.135 3.365,5.333 0.458,0.198 10 false 17 5.531,3.667 5.99,3.865 0.458,0.198 10 false K71 5.854,3.667 7.042,4.021 1.188,0.354 10 false Steering Sensor 5.729,2.656 6.188,2.854 0.458,0.198 10 false 3 5.719,3.198 6.177,3.396 0.458,0.198 10 false 8 5.938,2.76 6.396,2.958 0.458,0.198 10 false CANH 5.938,3.302 6.396,3.5 0.458,0.198 10 false CANL 5.667,4.708 6.125,4.906 0.458,0.198 10 false 31 5.677,5.24 6.135,5.438 0.458,0.198 10 false 30 5.938,4.823 6.396,5.021 0.458,0.198 10 false CA3P 5.938,5.375 6.396,5.573 0.458,0.198 10 false CA3L 5.333,5.74 5.792,5.938 0.458,0.198 10 false K70 5.656,5.74 7.052,6.323 1.396,0.583 10 false Hybrid Vehicle Control ECU Assembly 2.958,5.781 4.219,6.479 1.26,0.698 10 false No. 4 CAN Junction Connector 0.406,5.083 0.865,5.281 0.458,0.198 10 false 120 Ω 0.927,4.729 1.385,4.927 0.458,0.198 10 false CANH 0.938,5.26 1.396,5.458 0.458,0.198 10 false CANL 1.406,4.719 1.865,4.917 0.458,0.198 10 false 26 1.417,5.25 1.875,5.448 0.458,0.198 10 false 27 0.063,5.75 0.521,5.948 0.458,0.198 10 false K73 0.354,5.75 1.958,6.177 1.604,0.427 10 false Airbag Sensor Assembly

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 3 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the R99 No. 3 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C402513C55
3.542,1.354 4.021,1.583 0.479,0.229 0.271,1.354 0.729,1.594 0.458,0.24 2.885,1.698 2.885,2.198 2.885,2.198 3.052,2.198 true 5.24,1.167 5.24,0.667 5.24,0.667 5.073,0.667 true 2.396,1.698 2.396,2.198 2.396,2.198 2.229,2.198 true 2.885,1.427 2.885,0.677 2.885,0.677 3.052,0.677 true 2.385,1.427 2.385,0.677 2.385,0.677 2.219,0.677 true 2.542,1.427 2.542,0.427 2.542,0.427 2.375,0.427 true 2.552,1.688 2.552,2.438 2.552,2.438 2.385,2.438 true 2.719,1.427 2.719,0.427 2.719,0.427 2.885,0.427 true 2.719,1.688 2.719,2.438 2.719,2.438 2.885,2.438 true 0.604,0.302 0.917,0.5 0.313,0.198 10 false *a 3.854,0.333 4.167,0.531 0.313,0.198 10 false *1 0.385,1.385 0.781,1.583 0.396,0.198 10 false R99 3.625,1.385 4.021,1.583 0.396,0.198 10 false K154 4.792,0.594 5.188,0.792 0.396,0.198 10 false CG 1.667,0.594 2.313,0.844 0.646,0.25 10 false CANH*b 3.115,0.594 3.76,0.844 0.646,0.25 10 false CANH*e 1.708,2.115 2.354,2.365 0.646,0.25 10 false CANL*b 3.146,2.115 3.792,2.365 0.646,0.25 10 false CANL*e 1.813,0.344 2.458,0.594 0.646,0.25 10 false CANH*c 1.844,2.354 2.49,2.604 0.646,0.25 10 false CANL*c 2.958,2.354 3.604,2.604 0.646,0.25 10 false CANL*d 2.938,0.344 3.583,0.594 0.646,0.25 10 false CANH*d
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 3 Junction Connector)
*b to Tire Pressure Warning ECU and Receiver
(w/ Tire Pressure Warning System and Tire Inflation Pressure Display Function)
*c to Occupant Detection ECU
(w/ Occupant Classification System)
*d to Central Gateway ECU (Network Gateway ECU)
*e to No. 2 CAN Junction Connector - -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
R99-8 (CANH) - K154-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Tire pressure warning ECU and receiver*1
R99-19 (CANL) - K154-4 (CG)
R99-9 (CANH) - K154-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Occupant detection ECU*2
R99-20 (CANL) - K154-4 (CG)
R99-10 (CANH) - K154-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
R99-21 (CANL) - K154-4 (CG)
R99-11 (CANH) - K154-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher No. 2 CAN junction connector
R99-22 (CANL) - K154-4 (CG)


·

*1: w/ Tire Pressure Warning System and Tire Inflation Pressure Display Function

·

*2: w/ Occupant Classification System



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to No. 2 CAN junction connector) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 3 JUNCTION CONNECTOR

B

2.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 3 JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

3.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 2 CAN JUNCTION CONNECTOR)

D

6.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
2.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 3 JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the K76 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

C402513C56
3.542,1.354 4.021,1.604 0.479,0.25 0.271,1.354 0.729,1.594 0.458,0.24 2.719,1.698 2.719,2.198 2.719,2.198 2.885,2.198 true 5.24,1.167 5.24,0.667 5.24,0.667 5.073,0.667 true 2.719,1.417 2.719,0.667 2.719,0.667 2.885,0.667 true 0.604,0.302 0.917,0.5 0.313,0.198 10 false *a 3.854,0.333 4.167,0.531 0.313,0.198 10 false *1 0.354,1.385 0.75,1.583 0.396,0.198 10 false R99 3.625,1.385 4.021,1.583 0.396,0.198 10 false K154 4.813,0.583 5.208,0.781 0.396,0.198 10 false CG 2.99,0.583 3.635,0.833 0.646,0.25 10 false CANH*b 2.958,2.115 3.604,2.365 0.646,0.25 10 false CANL*b
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 3 Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Standard Resistance:
Tester Connection Condition Specified Condition
R99-10 (CANH) - K154-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
R99-21 (CANL) - K154-4 (CG)



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

3.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 2 CAN JUNCTION CONNECTOR)
a.

Disconnect the A67 No. 2 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

C402513C57
3.542,1.354 4.052,1.625 0.51,0.271 0.271,1.354 0.729,1.594 0.458,0.24 2.052,1.698 2.052,2.198 2.052,2.198 2.219,2.198 true 5.24,1.167 5.24,0.667 5.24,0.667 5.073,0.667 true 1.219,1.698 1.219,2.198 1.219,2.198 1.052,2.198 true 2.042,1.427 2.042,0.677 2.042,0.677 2.208,0.677 true 1.208,1.427 1.208,0.677 1.208,0.677 1.042,0.677 true 1.375,1.427 1.375,0.427 1.375,0.427 1.208,0.427 true 1.885,1.698 1.885,2.365 1.885,2.365 2.052,2.365 true 1.885,1.427 1.885,0.427 1.885,0.427 2.052,0.427 true 1.552,1.427 1.552,0.26 1.552,0.26 1.385,0.26 true 1.708,1.427 1.708,0.26 1.708,0.26 1.875,0.26 true 1.563,1.708 1.563,2.542 1.563,2.542 1.396,2.542 true 1.385,1.698 1.385,2.365 1.385,2.365 1.219,2.365 true 1.719,1.698 1.719,2.531 1.719,2.531 1.885,2.531 true 0.292,0.302 0.604,0.5 0.313,0.198 10 false *a 3.854,0.333 4.167,0.531 0.313,0.198 10 false *1 0.375,1.385 0.771,1.583 0.396,0.198 10 false A67 3.635,1.385 4.031,1.583 0.396,0.198 10 false K154 4.813,0.583 5.208,0.781 0.396,0.198 10 false CG 0.49,0.604 1.135,0.854 0.646,0.25 10 false CANH*b 2.26,0.594 2.906,0.844 0.646,0.25 10 false CANH*g 0.51,2.104 1.156,2.354 0.646,0.25 10 false CANL*b 2.292,2.104 2.938,2.354 0.646,0.25 10 false CANL*g 0.656,0.354 1.302,0.604 0.646,0.25 10 false CANH*c 0.688,2.281 1.333,2.531 0.646,0.25 10 false CANL*c 2.115,2.281 2.76,2.531 0.646,0.25 10 false CANL*f 2.125,0.354 2.771,0.604 0.646,0.25 10 false CANH*f 0.813,0.188 1.458,0.438 0.646,0.25 10 false CANH*d 1.948,0.177 2.594,0.427 0.646,0.25 10 false CANH*e 0.865,2.458 1.51,2.625 0.646,0.167 10 false CANL*d 1.958,2.458 2.604,2.708 0.646,0.25 10 false CANL*e
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to Brake Booster with Master Cylinder Assembly
*c to No. 3 Junction Connector *d to ECM
*e to Rack and Pinion Power Steering Gear Assembly *f to No. 4 CAN Junction Connector
*g to Brake Actuator Assembly - -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A67-1 (CANH) - K154-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Brake booster with master cylinder assembly
A67-12 (CANL) - K154-4 (CG)
A67-2 (CANH) - K154-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher No. 3 junction connector
A67-13 (CANL) - K154-4 (CG)
A67-3 (CANH) - K154-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher ECM
A67-14 (CANL) - K154-4 (CG)
A67-4 (CANH) - K154-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Rack and pinion power steering gear assembly
A67-15 (CANL) - K154-4 (CG)
A67-5 (CANH) - K154-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher No. 4 CAN junction connector
A67-16 (CANL) - K154-4 (CG)
A67-6 (CANH) - K154-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Brake actuator assembly
A67-17 (CANL) - K154-4 (CG)



Result:
Result Proceed to
OK A
NG (Line to No. 3 junction connector) B
NG (Line to No. 4 CAN junction connector) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

C

4.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 CAN JUNCTION CONNECTOR)

D

6.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
4.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 CAN JUNCTION CONNECTOR)
a.

Disconnect the K128 No. 4 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

C402513C58
3.531,1.354 4.031,1.604 0.5,0.25 0.271,1.354 0.729,1.594 0.458,0.24 2.052,1.698 2.052,2.198 2.052,2.198 2.219,2.198 true 5.24,1.177 5.24,0.677 5.24,0.677 5.073,0.677 true 2.042,1.417 2.042,0.667 2.042,0.667 2.208,0.667 true 1.885,1.417 1.885,0.667 1.885,0.667 1.719,0.667 true 1.896,1.698 1.896,2.198 1.896,2.198 1.729,2.198 true 0.604,0.302 0.917,0.5 0.313,0.198 10 false *a 3.854,0.333 4.167,0.531 0.313,0.198 10 false *1 0.354,1.385 0.75,1.583 0.396,0.198 10 false K128 3.625,1.385 4.021,1.583 0.396,0.198 10 false K154 4.792,0.604 5.188,0.802 0.396,0.198 10 false CG 2.271,0.583 2.917,0.833 0.646,0.25 10 false CANH*c 2.292,2.104 2.938,2.354 0.646,0.25 10 false CANL*c 1.156,0.583 1.802,0.833 0.646,0.25 10 false CANH*b 1.188,2.115 1.833,2.365 0.646,0.25 10 false CANL*b
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to Hybrid Vehicle Control ECU Assembly
*c to Airbag Sensor Assembly - -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
K128-5 (CANH) - K154-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Hybrid vehicle control ECU assembly
K128-16 (CANL) - K154-4 (CG)
K128-6 (CANH) - K154-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Airbag sensor assembly
K128-17 (CANL) - K154-4 (CG)



Result:
Result
OK
NG



OK

5.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 CAN JUNCTION CONNECTOR)

NG

6.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
5.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 CAN JUNCTION CONNECTOR)
a.

Disconnect the K127 No. 4 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

C402513C59
3.531,1.344 4.031,1.604 0.5,0.26 0.271,1.354 0.729,1.594 0.458,0.24 2.219,1.698 2.219,2.198 2.219,2.198 2.385,2.198 true 5.24,1.156 5.24,0.656 5.24,0.656 5.073,0.656 true 2.063,1.698 2.063,2.198 2.063,2.198 1.896,2.198 true 2.208,1.427 2.208,0.677 2.208,0.677 2.375,0.677 true 2.042,1.427 2.042,0.677 2.042,0.677 1.875,0.677 true 0.292,0.302 0.604,0.5 0.313,0.198 10 false *a 3.854,0.333 4.167,0.531 0.313,0.198 10 false *1 0.354,1.385 0.75,1.583 0.396,0.198 10 false K127 3.625,1.385 4.021,1.583 0.396,0.198 10 false K154 4.813,0.573 5.208,0.771 0.396,0.198 10 false CG 1.313,0.604 1.958,0.854 0.646,0.25 10 false CANH*b 2.448,0.594 3.094,0.844 0.646,0.25 10 false CANH*c 1.354,2.115 2,2.365 0.646,0.25 10 false CANL*b 2.458,2.104 3.104,2.354 0.646,0.25 10 false CANL*c
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to No. 2 CAN Junction Connector
*c to Steering Sensor - -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
K127-6 (CANH) - K154-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher No. 2 CAN junction connector
K127-17 (CANL) - K154-4 (CG)
K127-7 (CANH) - K154-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Steering sensor
K127-18 (CANL) - K154-4 (CG)



Result:
Result Proceed to
OK A
NG (Line to No. 2 CAN junction connector) B
NG (Line to ECU or sensor) C



A

REPLACE NO. 4 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

C

6.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
6.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to GND is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.

Measure the resistance according to the value(s) in the table below.

C402517C18
1.594,0.198 2.01,0.469 0.417,0.271 4.927,0.313 5.479,0.51 0.552,0.198 1.406,1.229 1.406,0.625 1.406,0.625 1.271,0.625 true 1.292,2.104 1.427,2.104 1.427,2.104 1.427,1.406 true 4.958,0.698 5.125,0.698 5.125,0.698 5.125,1.115 true 3.958,0.354 4.271,0.552 0.313,0.198 10 false *1 1.677,0.25 1.99,0.448 0.313,0.198 10 false K76 0.885,0.552 1.438,0.75 0.552,0.198 10 false CA2L 4.698,0.625 5.25,0.823 0.552,0.198 10 false CG 0.885,2.031 1.438,2.229 0.552,0.198 10 false CA2H 5.042,0.333 5.625,0.531 0.583,0.198 10 false K154 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a
*1 DLC3 - -
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Tester Connection Condition Specified Condition
K76-22 (CA2H) - K154-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K76-7 (CA2L) - K154-4 (CG)


HINT:
·

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to ground in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Result
OK
NG



OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR