Home › Power Source / Network › NETWORKING › NETWORK GATEWAY ECU › 2017.12–2019.02
RM33C0E _57 Power Source / Network _065454 NETWORKING _0329711 NETWORK GATEWAY ECU A

NETWORKING  NETWORK GATEWAY ECU  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during central gateway ECU (network gateway ECU) removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Replacement of certification ECU (smart key ECU assembly) Code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart entry and start system (for entry function)

·

Smart entry and start system (for start function)

·

Steering lock function


See Service Bulletin for the registration method.
Replacement of clearance warning ECU assembly Adjust TOYOTA parking assist-sensor system TOYOTA parking assist-sensor system (Click here)

CAUTION:
B401522

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 64718C 2.REMOVE LUGGAGE TRIM SERVICE HOLE COVER

Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>AUXILIARY BATTERY>REMOVAL

CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If an airbag deploys for any reason, it may cause a serious injury.



Hide 55435B 4.REMOVE NO. 1 METER HOOD CLUSTER (for LHD)

Hide 55012A 5.REMOVE NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY (for LHD)

Hide 55476C 6.REMOVE INSTRUMENT PANEL FINISH PLATE GARNISH (for LHD)

Hide 67913 7.REMOVE FRONT DOOR SCUFF PLATE RH (for LHD)

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 62111A 8.REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH (for LHD)

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 62311B 9.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for LHD)

Hide 55317A 10.REMOVE INSTRUMENT SIDE PANEL RH (for LHD)

Hide 55607 11.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)

Hide 73990 12.REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY (for LHD, w/ Passenger Side Knee Airbag)

Hide 55303B 13.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (for LHD, w/o Passenger Side Knee Airbag)

Hide 55303B 14.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (for LHD, w/ Passenger Side Knee Airbag)

Hide 82877 15.REMOVE ECU INTEGRATION BOX RH (for LHD)

a.

Disconnect each connector.


b.
C380668

Disengage the 2 clamps.


c.

Remove the bolt, nut and ECU integration box RH.


Hide 89111 16.REMOVE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) (for LHD)

a.
C380669

Disengage the 2 claws and remove the central gateway ECU (network gateway ECU).

NOTICE:
·

If the ECU integration box is deformed or damaged, replace it.

·

Do not bend the 2 claws more than necessary.




Hide 55435B 17.REMOVE NO. 1 METER HOOD CLUSTER (for RHD)

HINT:

Use the same procedure as for LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX>REMOVAL


Hide 55434B 18.REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL (for RHD)

HINT:

Use the same procedure as for LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX>REMOVAL


Hide 67913 19.REMOVE FRONT DOOR SCUFF PLATE RH (for RHD)

HINT:

Use the same procedure as for LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 62111A 20.REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH (for RHD)

HINT:

Use the same procedure as for LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 62311B 21.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for RHD)

HINT:

Use the same procedure as for LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL


Hide 55317A 22.REMOVE INSTRUMENT SIDE PANEL RH (for RHD)

HINT:

Use the same procedure as for LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL


Hide 55606 23.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)

Hide 55436B 24.REMOVE NO. 2 METER HOOD CLUSTER (for RHD)

HINT:

Use the same procedure as for LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL


Hide 53601 25.DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY (for RHD)

HINT:

Use the same procedure as for LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL


Hide 55302D 26.REMOVE NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY (for RHD, w/o Driver Side Knee Airbag)

Hide 55302D 27.REMOVE NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY (for RHD, w/ Driver Side Knee Airbag)

HINT:

Use the same procedure as for LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL


Hide 73900 28.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (for RHD, w/ Driver Side Knee Airbag)

Hide 55308B 29.REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY (for RHD)

HINT:

Use the same procedure as for LHD.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>REMOVAL


Hide 82877 30.REMOVE ECU INTEGRATION BOX RH (for RHD)

a.

Disconnect each connector.


b.
C377921

Disengage the clamp.


c.

Remove the bolt, 2 nuts and ECU integration box RH.


Hide 89111 31.REMOVE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) (for RHD)

a.
C377923

Disengage the 2 claws and remove the central gateway ECU (network gateway ECU).

NOTICE:
·

If the ECU integration box is deformed or damaged, replace it.

·

Do not bend the 2 claws more than necessary.