Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2019.02
RM33C0E _58 Vehicle Interior _065460 SUPPLEMENTAL RESTRAINT SYSTEMS _0331857 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  Trouble in Passenger Airbag ON/OFF Indicator  


DESCRIPTION

This circuit detects the airbag cut off switch cylinder sub-assembly status.

The passenger airbag ON/OFF indicator comes on to inform the driver of the instrument panel passenger airbag assembly status (activated or deactivated).

HINT:

Refer to the normal condition of the passenger airbag ON/OFF indicator.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>OPERATION CHECK


WIRING DIAGRAM

B512690E05
4.854,2.979 5.438,3.313 0.583,0.333 10 false K73 4.844,3.146 6.646,3.542 1.802,0.396 10 false Airbag Sensor Assembly 0.542,2.823 1.125,3.156 0.583,0.333 10 false K158 0.542,3 3.542,3.302 3,0.302 10 false Airbag Cut Off Switch Cylinder Sub-assembly 2.219,1.115 2.802,1.448 0.583,0.333 10 false 2 1.729,1.115 2.313,1.448 0.583,0.333 10 false PMC+ 1.75,2.302 2.333,2.635 0.583,0.333 10 false PMC- 2.208,2.302 2.792,2.635 0.583,0.333 10 false 1 4.885,1.104 5.469,1.438 0.583,0.333 10 false MSW+ 4.635,1.104 5.219,1.438 0.583,0.333 10 false 22 4.885,2.302 5.469,2.635 0.583,0.333 10 false MSW- 4.635,2.302 5.219,2.635 0.583,0.333 10 false 21

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


PROCEDURE

1.CHECK SRS WARNING LIGHT
a.

Turn the power switch on (IG), and check the SRS warning light condition.

OK:

After the primary check period, the SRS warning light turns off.


HINT:
·

If the SRS warning light is on when this malfunction occurs, a DTC is stored. Troubleshoot for the stored DTC.

·

The primary check period is approximately 6 seconds after the power switch is turned on (IG).




Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTION OF CONNECTORS

NG

2.CHECK CONNECTION OF CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly and airbag cut off switch cylinder sub-assembly.

OK:

The connectors are properly connected.



Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly and airbag cut off switch cylinder sub-assembly.


b.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

4.CHECK INSTRUMENT PANEL WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

4.CHECK INSTRUMENT PANEL WIRE
a.
B512677C04
0.781,0.854 1.146,1.073 0.365,0.219 0.479,3.74 0.927,3.958 0.448,0.219 1.458,2.604 1.458,2.104 1.458,2.104 1.292,2.104 false 1.792,1.729 1.792,1.604 false 1.292,1.594 1.76,1.094 true 2.281,1.594 1.833,1.094 true 0.99,4.26 1.229,3.927 true 1.688,4.26 1.479,3.927 true 0.448,2.573 0.854,2.979 0.406,0.406 10 false *1 2.552,2.563 3.073,3.208 0.521,0.646 10 false *2 1.135,2.021 1.51,2.406 0.375,0.385 10 false *3 1.729,1.74 2.125,1.979 0.396,0.24 10 false *4 0.667,0.198 1.073,0.542 0.406,0.344 10 false *a 0.375,3.406 0.792,3.719 0.417,0.313 10 false *b 2.177,2.563 2.698,3.208 0.521,0.646 10 false A 1.813,2.563 2.333,3.208 0.521,0.646 10 false B 1.063,2.573 1.583,3.219 0.521,0.646 10 false C 0.698,2.573 1.219,3.219 0.521,0.646 10 false D 0.844,0.885 1.25,1.229 0.406,0.344 10 false K73 1.115,1.604 1.604,1.99 0.49,0.385 10 false MSW- 2.125,1.604 2.667,2.01 0.542,0.406 10 false MSW+ 1.563,4.271 2.177,4.604 0.615,0.333 10 false PMC+ 0.833,4.271 1.448,4.604 0.615,0.333 10 false PMC- 0.542,3.771 0.948,4.115 0.406,0.344 10 false K158
*1 Airbag Cut Off Switch Cylinder Sub-assembly
*2 Airbag Sensor Assembly
*3 Instrument Panel Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Airbag Cut Off Switch Cylinder Sub-assembly)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K158-2 (PMC+) - Body ground Power switch on (IG) Below 1 V
K158-1 (PMC-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



f.

Using a service wire, connect terminals 22 (MSW+) and 21 (MSW-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K158-2 (PMC+) - K158-1 (PMC-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K158-2 (PMC+) - K158-1 (PMC-) Always 1 MΩ or higher
K158-2 (PMC+) - Body ground Always 1 MΩ or higher
K158-1 (PMC-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK AIRBAG CUT OFF SWITCH CYLINDER SUB-ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

5.CHECK AIRBAG CUT OFF SWITCH CYLINDER SUB-ASSEMBLY
a.
C261687C19
2.281,1.052 2.729,0.771 false 2.281,1.135 2.729,1.417 false 0.073,0.063 0.354,0.365 0.281,0.302 10 false *a 2.781,0.698 3.25,1.042 0.469,0.344 10 false PMC+ 2.792,1.333 3.26,1.677 0.469,0.344 10 false PMC-
*a Component without harness connected
(Airbag Cut Off Switch Cylinder Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (PMC+) - 1 (PMC-) Cut off switch in ON position 360 to 440 Ω
2 (PMC+) - 1 (PMC-) Cut off switch in OFF position 90 to 110 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE AIRBAG CUT OFF SWITCH CYLINDER SUB-ASSEMBLY