Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CENTER AIRBAG SENSOR ASSEMBLY › 2019.02–2021.02
RM33C0E _58 Vehicle Interior _065460 SUPPLEMENTAL RESTRAINT SYSTEMS _0331867 CENTER AIRBAG SENSOR ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  CENTER AIRBAG SENSOR ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during airbag sensor assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: w/ Occupant Classification System

*2: When performing learning using the GTS

Click here(Click here)

Replacement of the airbag sensor assembly
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Removal/installation of the front passenger seat*1 Zero point calibration (Occupant classification system)
·

Occupant classification system

·

Passenger airbag ON/OFF indicator

·

Airbag system (Front passenger side)

·

Seat belt warning system (Front passenger)


(Click here)
Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Parking Support Brake System*2
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The following procedure is for an LHD vehicle.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.REMOVE FRONT SEAT ASSEMBLY (for Power Seat)

Hide 3.REMOVE FRONT SEAT ASSEMBLY (for Manual Seat)

Hide 58810J 4.REMOVE CONSOLE BOX ASSEMBLY

Hide 67914 5.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 62112A 6.REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

Hide 62312B 7.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:

Disconnect the front door opening trim weatherstrip LH to the extent that allows the removal of the lower center pillar garnish LH.


Hide 67918A 8.REMOVE REAR DOOR SCUFF PLATE LH

Hide 62332A 9.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH

HINT:

Disconnect the rear door opening trim weatherstrip LH to the extent that allows the removal of the lower center pillar garnish LH.


Hide 62414A 10.REMOVE LOWER CENTER PILLAR GARNISH LH

Hide 55606 11.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)

Hide 55606 12.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)

Hide 67913 13.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 62111A 14.REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 62311B 15.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Disconnect the front door opening trim weatherstrip RH to the extent that allows the removal of the lower center pillar garnish RH.


Hide 67917A 16.REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 62331A 17.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Disconnect the rear door opening trim weatherstrip RH to the extent that allows the removal of the lower center pillar garnish RH.


Hide 62413A 18.REMOVE LOWER CENTER PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 55607 19.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 58569D 22.REMOVE FRONT FLOOR CAUTION PLATE COVER

Hide 58510D 23.DISCONNECT FRONT FLOOR CARPET ASSEMBLY

a.

for LHD:

i.
E366971

Remove the front floor carpet clip.



b.
E372079

Remove the front floor carpet clip.


c.
E377302

Disengage the 2 guides and turn back the front floor carpet assembly as shown in the illustration.


d.
E366970

Remove the front floor carpet clip.


e.
E372078

Remove the front floor carpet clip.


f.
E377300

Disengage the 2 guides and turn back the front floor carpet assembly as shown in the illustration.


Hide 58861B 24.REMOVE NO. 1 CONSOLE BOX DUCT

a.
C378612C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the clip.


b.

Remove the No. 1 console box duct as shown in the illustration.


Hide 89170 25.REMOVE AIRBAG SENSOR ASSEMBLY

a.

Check that the power switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.
B468737C01
1.063,2.479 0.823,3.031 0.823,3.031 0.604,3.031 true 1.156,2.479 1.375,2.479 true 0.458,2.938 0.604,3.146 0.146,0.208 10 true A 1.406,2.385 1.552,2.594 0.146,0.208 10 true *a
*a Lock Lever
V113147

Release the lock (1)
V113148

Disconnect the connector (2)


Push down the part (A) in the direction indicated by the arrow (1) to release the lock, and then move the lock lever in the direction indicated by the arrow (2) shown in the illustration to disconnect the connectors.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.



d.
B468739

Remove the 3 bolts and airbag sensor assembly.