Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › from 2019.02
RM33C0E _54 Brake _065442 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0328411 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C14B6  Stroke Sensor / Reaction Force Pressure Sensor Output Inconsistent  


DESCRIPTION

If the skid control ECU (brake booster with master cylinder assembly) detects an inconsistency between the brake pedal stroke sensor assembly signal and reaction force pressure sensor signal, DTC C14B6 is stored.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C14B6 Stroke Sensor / Reaction Force Pressure Sensor Output Inconsistent 209 The difference between brake pedal stroke sensor assembly output value and reaction force pressure sensor output value is above the threshold for a certain period of time.
·

Brake actuator (brake booster with master cylinder assembly)

·

Brake pedal stroke sensor assembly


Electronically controlled brake system DTC

CAUTION / NOTICE / HINT

NOTICE:

After replacing the brake actuator (brake booster with master cylinder assembly) or brake pedal stroke sensor assembly perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


PROCEDURE

1.CUSTOMER PROBLEM ANALYSIS (CHECK CONDITION WHEN MALFUNCTION OCCURRED) AND FREEZE FRAME DATA
a.

Interview the customer to check the vehicle conditions when the brake warning light / yellow (minor malfunction) illuminated.


b.

Using the GTS, read the "Shift Lever Position", "Vehicle Speed", "Yaw Rate Sensor", "Steering Angle Sensor", "Stop Light SW", "Stroke Sensor", "Reaction Force Pressure", "Servo Pressure" and "Accumulator Pressure" of the Freeze Frame Data stored when the DTC was stored.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>FREEZE FRAME DATA


HINT:
·

Freeze Frame Data is only stored once when a DTC is stored.

·

If other DTCs are output, repair any malfunctions related to those DTCs first, and then reproduce the conditions that caused DTC C14B6 to be stored based on the interview with the customer.



Result:
Proceed to
NEXT



NEXT

2.INSPECT BRAKE PEDAL STROKE SENSOR ASSEMBLY OUTPUT VOLTAGES AND WHEEL CYLINDER PRESSURE
2.INSPECT BRAKE PEDAL STROKE SENSOR ASSEMBLY OUTPUT VOLTAGES AND WHEEL CYLINDER PRESSURE
a.

Turn the power switch off.


b.

Mount a pedal effort gauge.


c.

Disconnect the A45 brake booster pump assembly connector.


d.

Depress the brake pedal 10 times or more until it becomes hard.

HINT:

Depressing the brake pedal with the connector of the brake booster pump assembly disconnected drops the accumulator pressure to approximately 0 MPa.



e.

Connect an LSPV gauge set.


f.

Select the Data List on the GTS.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stroke Sensor Brake pedal stroke sensor assembly Min.: 0.00 V, Max.: 5.00 V Brake pedal released: 0.65 to 1.35 V Reading increases when brake pedal is depressed
Chassis > ABS/VSC/TRC > Data List
Tester Display
Stroke Sensor
50003 105 11

g.

Slowly depress the brake pedal and check the brake pedal stroke sensor assembly output voltages and the wheel cylinder pressure with respect to brake pedal depression force.

NOTICE:

Check the wheel cylinder pressure with the switching solenoid (SSA, SGH) off and an accumulator pressure of 0 MPa.


Standard Pressure:
for Front Right Wheel (except 2-Pot Caliper)
Brake Effort
[N (kgf, lbf)]
Stroke Sensor
[V]
Hydraulic Pressure
[MPa (kgf/cm2, psi)]
200 (20, 45.0) 1.52 to 2.22 0.04 (0.4, 5.8) to 2.04 (20.8, 296)
500 (51, 112.4) 1.81 to 2.51 2.06 (21.0, 299) to 4.06 (41.4, 589)

for Front Left Wheel (except 2-Pot Caliper)
Brake Effort
[N (kgf, lbf)]
Stroke Sensor
[V]
Hydraulic Pressure
[MPa (kgf/cm2, psi)]
200 (20, 45.0) 1.52 to 2.22 0.04 (0.4, 5.8) to 2.04 (20.8, 296)
500 (51, 112.4) 1.81 to 2.51 2.06 (21.0, 299) to 4.06 (41.4, 589)

for Front Right Wheel (for 2-Pot Caliper)
Brake Effort
[N (kgf, lbf)]
Stroke Sensor
[V]
Hydraulic Pressure
[MPa (kgf/cm2, psi)]
200 (20, 45.0) 1.69 to 2.39 0.02 (0.2, 2.9) to 2.02 (20.6, 293)
500 (51, 112.4) 1.97 to 2.67 2.05 (20.9, 297) to 4.05 (41.3, 587)

for Front Left Wheel (for 2-Pot Caliper)
Brake Effort
[N (kgf, lbf)]
Stroke Sensor
[V]
Hydraulic Pressure
[MPa (kgf/cm2, psi)]
200 (20, 45.0) 1.69 to 2.39 0.02 (0.2, 2.9) to 2.02 (20.6, 293)
500 (51, 112.4) 1.97 to 2.67 2.05 (20.9, 297) to 4.05 (41.3, 587)



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

3.REPLACE BRAKE PEDAL STROKE SENSOR ASSEMBLY
3.REPLACE BRAKE PEDAL STROKE SENSOR ASSEMBLY
a.

Turn the power switch off.


b.

Reconnect the A45 brake booster pump assembly connector.



d.

Perform zero point calibration of the brake pedal stroke sensor assembly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION

Chassis > ABS/VSC/TRC > Utility
Tester Display
ECB Utility
50005 105 167

Result:
Proceed to
NEXT



NEXT

4.RECONFIRM DTC
4.RECONFIRM DTC
a.

Clear the DTCs.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Perform a road test under the same malfunction conditions recreated based on the Freeze Frame Data or customer problem analysis.


c.

Turn the power switch off and wait for 2 minutes or more.


d.

Turn the power switch on (IG).


e.

Check if the same DTC is output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C14B6 is not output. A
DTC C14B6 is output. B



A

END

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY