Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for LHD) › 2019.02–2021.02
RM33C0E _54 Brake _065443 BRAKE SYSTEM (OTHER) _0319351 BRAKE BOOSTER(for LHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during brake booster with master cylinder assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Departure Alert System (w/ Steering Control) (Click here)
Parking Support Brake System*
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Replacement of brake booster with master cylinder assembly
1.

Bleed air

2.

Clear the data stored during previous linear solenoid valve offset learning, ABS holding solenoid valve learning, brake pedal stroke sensor assembly zero point calibration and system information memorization.

3.

Perform linear solenoid valve offset learning, ABS holding solenoid valve learning, brake pedal stroke sensor assembly zero point calibration and system information memorization.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)for Initialization
(Click here)for Calibration
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.



CAUTION / NOTICE / HINT

NOTICE:

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.PERFORM ACCUMULATOR PRESSURE ZERO DOWN

a.

Using the GTS, perform the accumulator pressure zero down operation.

i.

Connect the GTS to the DLC3 with the power switch off.


ii.

Turn the power switch on (IG).


iii.

Turn the GTS on and enter the following menus: Chassis / ABS/VSC/TRC / Utility / ECB (Electronically Controlled Brake system) Utility.

Chassis > ABS/VSC/TRC > Utility
Tester Display
ECB Utility
50005 105 167

iv.

Select "Motor Invalid" on the "ECB (Electronically Controlled Brake system) Utility" screen.


v.

Perform "Motor Invalid" according to the display on the GTS.


vi.

Enter the following menus: Chassis / ABS/VSC/TRC / Utility / ECB (Electronically Controlled Brake system) Utility.

Chassis > ABS/VSC/TRC > Utility
Tester Display
ECB Utility
50005 105 167

vii.

Select "ECB (Electronically Controlled Brake system) Invalid" on the "ECB (Electronically Controlled Brake system) Utility" screen.


viii.

Perform "ECB (Electronically Controlled Brake system) Invalid" according to the display on the GTS.


ix.

Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.

HINT:

A buzzer may sound due to low accumulator pressure. As this is not a malfunction, continue the procedure.



x.

Check that the brake pedal is firm.

NOTICE:

If the brake pedal is not firm or the pump motor continues to operate even after depressing the brake pedal 40 times or more, the accumulator pressure zero down operation is not complete.



xi.

Turn the GTS off and turn the power switch off.


xii.

Disconnect the GTS from the DLC3.


xiii.

Disconnect the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>AUXILIARY BATTERY>REMOVAL



b.

When the accumulator pressure zero down could not be performed using the GTS.

NOTICE:

If DTCs are output, the accumulator pressure zero down operation may not be complete. In this case, perform the following procedure.


i.
C377744C01
0,0 0,0 false
V113147

Release the lock lever
V113148

Disconnect the connector


With the power switch off, release the lock lever and disconnect the brake booster pump assembly connector as shown in the illustration.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



ii.

Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.


iii.

Check that the brake pedal is firm.

NOTICE:

If the brake pedal is not firm or the pump motor continues to operate even after depressing the brake pedal 40 times or more, the accumulator pressure zero down operation is not complete.



iv.

Disconnect the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>AUXILIARY BATTERY>REMOVAL



Hide 55708 3.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 53607A 4.REMOVE FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY

a.
C380687

Disconnect the connector.


b.

Disengage the 2 clamps and separate the wire harness.


c.
C377997

Remove the 6 bolts, 4 nuts and front center upper suspension brace sub-assembly.


Hide 5.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 82111 6.DISCONNECT ENGINE ROOM MAIN WIRE

a.
C377746

Disconnect the connector from the brake booster with master cylinder assembly.


b.
C377747C01
1.365,2.5 1.594,2.5 true 2.115,3.01 2.271,3.01 2.271,3.01 2.375,2.823 true 2.979,2.542 2.875,2.542 2.875,2.542 2.792,2.656 true 1.615,2.427 1.927,2.583 0.313,0.156 10 false *a 1.969,2.938 2.281,3.094 0.313,0.156 10 false *b 2.198,2.417 2.51,2.573 0.313,0.156 10 false *c 3,2.458 3.313,2.615 0.313,0.156 10 false *a
*a Lock Lever
*b Lock Arm
*c Push
V113147

Release the lock lever


Push the lock arm of the connector to disengage the lock and release the lock lever as shown in the illustration.


c.
C377749C01
0.885,3.115 0.885,2.875 true 2.417,3.156 2.177,2.865 2.177,2.865 2,2.865 true 0.813,3.115 1.125,3.271 0.313,0.156 10 false *a 1.844,2.792 2.156,2.948 0.313,0.156 10 false *b
*a Screwdriver Insertion Point
*b Pre-lock
V113147

Disconnect the connector


Using a screwdriver, release the pre-lock and disconnect the connector from the brake booster with master cylinder assembly as shown in the illustration.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



Hide 44571A 7.DISCONNECT NO. 1 BRAKE ACTUATOR HOSE

a.
C377750

Slide the clip and disconnect the No. 1 brake actuator hose from the brake booster with master cylinder assembly.


Hide 8.DISCONNECT BRAKE LINE

a.
C377753

Using a union nut wrench, disconnect the 3 brake lines from the brake booster with master cylinder assembly.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




Hide 55606 9.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 47264A 10.REMOVE PUSH ROD PIN

a.
C377755

Remove the clip and push rod pin.


Hide 47210L 11.REMOVE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

a.
C377756C01
1.427,2.948 1.427,2.677 1.427,2.677 1.656,2.677 false 0.604,4.188 0.604,3.771 false 1.969,3.333 1.969,3.063 1.969,3.063 2.198,3.063 false 0.25,3.604 0.25,3.198 0.25,3.198 0.427,3.198 false 2.615,4.438 2.615,4.167 false 1.677,2.594 1.99,2.75 0.313,0.156 10 false *a 2.229,2.979 2.542,3.135 0.313,0.156 10 false *b 0.458,3.115 0.771,3.271 0.313,0.156 10 false *c 0.531,4.188 0.844,4.344 0.313,0.156 10 false *d 2.563,4.448 2.875,4.604 0.313,0.156 10 false *e
*a Skid Control ECU
*b No. 1 Reservoir Hose
*c Brake Master Cylinder Push Rod Clevis
*d Boot
*e Master Cylinder Reservoir Assembly


Remove the 4 nuts and brake booster with master cylinder assembly.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not carry the brake booster with master cylinder assembly by the parts shown in the illustration.

·

Be careful not to allow any brake fluid to enter the connector.




Hide 44785D 12.REMOVE BRAKE MASTER CYLINDER GASKET