Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2019.02–2021.02
RM33C0E _56 Audio / Visual / Telematics _065451 NAVIGATION / MULTI INFO DISPLAY _0333738 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B15DA  Rear Console Recognition Disconnected  


DESCRIPTION

The cooler control switch assembly is connected via AVC-LAN communication line.

This DTC is stored when an AVC-LAN communication error occurs between the radio and display receiver assembly and cooler control switch assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15DA Rear Console Recognition Disconnected A device that is listed in the AVC-LAN connected device record of the master unit is missing.
·

Cooler control switch assembly power source circuit

·

AVC-LAN circuit between radio and display receiver assembly and cooler control switch assembly

·

Cooler control switch assembly

·

Stereo component amplifier assembly

·

Radio and display receiver assembly

·

Harness or connector



HINT:

The radio and display receiver assembly is the master unit.


WIRING DIAGRAM

E292343E24
1.188,0.521 2.969,0.896 1.781,0.375 10 false from Battery 0.99,0.979 2.646,1.323 1.656,0.344 10 false from ACC Relay 0.656,1.448 2.313,1.792 1.656,0.344 10 false from IG1-NO. 1 Relay 3.375,0.677 4.323,1.021 0.948,0.344 10 false ECU-B NO. 2 3.438,1.156 4.146,1.479 0.708,0.323 10 false ECU-ACC 3.313,1.625 4.844,1.854 1.531,0.229 10 false ECU-IG1 NO. 4 1.677,2.302 2.115,2.625 0.438,0.323 10 false TX1+ 1.698,2.708 2.135,3.031 0.438,0.323 10 false TX1- 3.375,2.323 3.813,2.646 0.438,0.323 10 false TX+ 3.385,2.708 3.823,3.031 0.438,0.323 10 false TX- 3.896,2.313 4.333,2.635 0.438,0.323 10 false TXD+ 3.927,2.719 4.365,3.042 0.438,0.323 10 false TXD- 5.604,0.521 6.042,0.844 0.438,0.323 10 false +B 5.604,0.99 6.042,1.313 0.438,0.323 10 false ACC 5.604,1.458 6.042,1.781 0.438,0.323 10 false IG+ 5.594,3.51 6.031,3.833 0.438,0.323 10 false GND 5.604,2.302 6.042,2.625 0.438,0.323 10 false TX+ 5.615,2.719 6.052,3.042 0.438,0.323 10 false TX- 5.385,0.417 5.615,0.677 0.229,0.26 10 false 9 5.396,0.885 5.625,1.146 0.229,0.26 10 false 1 5.344,1.354 5.573,1.615 0.229,0.26 10 false 10 5.385,2.188 5.615,2.448 0.229,0.26 10 false 7 5.385,2.594 5.615,2.854 0.229,0.26 10 false 8 5.333,3.396 5.563,3.656 0.229,0.26 10 false 16 4.323,2.188 4.552,2.448 0.229,0.26 10 false 20 4.313,2.583 4.542,2.844 0.229,0.26 10 false 19 3.167,2.583 3.396,2.844 0.229,0.26 10 false 7 3.167,2.198 3.396,2.458 0.229,0.26 10 false 8 2.104,2.188 2.333,2.448 0.229,0.26 10 false 5 2.094,2.594 2.323,2.854 0.229,0.26 10 false 6 0.969,3.094 1.406,3.417 0.438,0.323 10 false K3 0.958,3.271 2.156,3.667 1.198,0.396 10 false Radio and Display Receiver Assembly 3.198,3.104 3.635,3.427 0.438,0.323 10 false K9 3.198,3.271 4.948,4.063 1.75,0.792 10 false Stereo Component Amplifier Assembly 1,4.302 3.24,4.604 2.24,0.302 10 false : AVC-LAN Communication Line 5.375,3.938 5.76,4.156 0.385,0.219 10 false Z1 5.365,4.094 6.708,4.646 1.344,0.552 10 false Cooler Control Switch Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION


·

When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:

-

A communication malfunction DTC may be stored.

-

The radio and display receiver assembly may not operate normally.



·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK DTC
a.

If DTC B15D3 is output, perform troubleshooting for DTC B15D3 first.

Result:
Result Proceed to
DTC B15D3 is not output. A
DTC B15D3 is output. B




A

2.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

2.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Check that optional components (including associated wiring) which generate radio waves are not installed.

Result:
Result Proceed to
Optional components (including associated wiring) are installed. A
Optional components (including associated wiring) are not installed. B


HINT:
·

Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

·

This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.





A

3.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

4.CHECK DTC
3.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Remove optional components (including associated wiring).

NOTICE:

Do not remove optional components or associated wiring without the permission of the customer.



Result:
Proceed to
NEXT



NEXT

4.CHECK DTC
4.CHECK DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

5.CHECK HARNESS AND CONNECTOR (COOLER CONTROL SWITCH ASSEMBLY POWER SOURCE)
5.CHECK HARNESS AND CONNECTOR (COOLER CONTROL SWITCH ASSEMBLY POWER SOURCE)
a.

Disconnect the Z1 cooler control switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z1-16 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Z1-9 (+B) - Z1-16 (GND) Always 11 to 14 V
Z1-10 (IG+) - Z1-16 (GND) Ignition switch ON 11 to 14 V
Z1-1 (ACC) - Z1-16 (GND) Ignition switch ACC 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (COOLER CONTROL SWITCH ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (COOLER CONTROL SWITCH ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the Z1 cooler control switch assembly connector.


b.

Disconnect the K9 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z1-7 (TX+) - K9-20 (TXD+) Always Below 1 Ω
Z1-8 (TX-) - K9-19 (TXD-) Always Below 1 Ω
Z1-7 (TX+) or K9-20 (TXD+) - Body ground Always 10 kΩ or higher
Z1-8 (TX-) or K9-19 (TXD-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE COOLER CONTROL SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE COOLER CONTROL SWITCH ASSEMBLY
a.

Replace the cooler control switch assembly with a new or known good one.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Reclining Seat Type)>REMOVAL


b.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

8.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY
8.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY
a.

Replace the stereo component amplifier assembly with a new or known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>STEREO COMPONENT AMPLIFIER>REMOVAL


b.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY