Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › from 2019.02
RM33C0E _58 Vehicle Interior _065456 THEFT DETERRENT / KEYLESS ENTRY _0385172 ENTRY AND START SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  B27A2  Open in Front Passenger Side Electrical Antenna Circuit  


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the front door outside handle assembly (for front passenger door) (electrical key antenna) at intervals of 0.25 seconds. For the front door outside handle assembly (for front passenger door) (electrical key antenna) to detect when the electrical key transmitter sub-assembly is brought close to the vehicle, a signal requesting a response from the electrical key transmitter sub-assembly is transmitted within approximately 1 m (3.28 ft.) of the front passenger door at intervals of 0.25 seconds. DTC B27A2 is stored by the certification ECU (smart key ECU assembly) when an open is detected between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for front passenger door) (electrical key antenna) (between terminals CLG2 and ANT1, or terminals CG2B and ANT2).

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B27A2 Open in Front Passenger Side Electrical Antenna Circuit An open is detected in the circuit between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for front passenger door) (CLG2 - ANT1, CG2B - ANT2) (This is detected by the malfunction detection circuit in the certification ECU (smart key ECU assembly)) (1 trip detection logic*).
·

Certification ECU (smart key ECU assembly)

·

Front door outside handle assembly (for front passenger door)

·

Harness or connector


DTC Output Confirmation Operation:

Any time



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Entry lock/unlock operation cannot be performed for front passenger door -

Related Data List and Active Test
DTC No. Data List and Active Test
B27A2 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

B482837E30
1.302,0.75 1.917,0.948 0.615,0.198 10 false ANT1 1.302,1.896 1.917,2.094 0.615,0.198 10 false ANT2 1.76,0.75 1.917,0.948 0.156,0.198 10 false 6 1.771,1.896 1.927,2.094 0.156,0.198 10 false 4 4.969,0.865 5.281,1.063 0.313,0.198 10 false R8 4.969,2.01 5.281,2.208 0.313,0.198 10 false R8 4.969,0.646 5.281,0.844 0.313,0.198 10 false 15 4.969,1.802 5.281,2 0.313,0.198 10 false 14 5.302,0.75 5.917,0.948 0.615,0.198 10 false CLG2 5.302,1.896 5.917,2.094 0.615,0.198 10 false CG2B 5.833,1.385 6.146,1.583 0.313,0.198 10 false IC 0.479,2.521 1.469,2.75 0.99,0.229 10 false N11*1, O10*2 0.49,2.677 2.792,3.385 2.302,0.708 10 false Front Door Outside Handle Assembly (for Front Passenger Door) 5.104,2.531 6.635,3.49 1.531,0.958 10 false Certification ECU (Smart Key ECU Assembly) 6.479,2.01 6.938,2.208 0.458,0.198 10 false K62 6.531,1.802 6.844,2 0.313,0.198 10 false 18 6.25,2 6.406,2.198 0.156,0.198 10 false E 3.427,2.875 4.417,3.104 0.99,0.229 10 false *1: for LHD 3.427,3.188 4.417,3.417 0.99,0.229 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK CONNECTOR CONNECTION
a.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and front door outside handle assembly (for front passenger door).

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR))

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR))
a.

Disconnect the R8 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the N11*1 or O10*2 front door outside handle assembly (for front passenger door) connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
R8-15 (CLG2) - N11-6 (ANT1) Always Below 1 Ω
R8-14 (CG2B) - N11-4 (ANT2) Always Below 1 Ω

for RHD:
Tester Connection Condition Specified Condition
R8-15 (CLG2) - O10-6 (ANT1) Always Below 1 Ω
R8-14 (CG2B) - O10-4 (ANT2) Always Below 1 Ω



d.

Reconnect the R8 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR))
B416825C43
4.521,0.469 4.917,0.698 0.396,0.229 3.271,0.469 3.667,0.698 0.396,0.229 2.927,2.302 3.146,1.354 false 3.354,2.292 3.219,1.354 false 5.417,2.24 5.219,1.469 false 0.25,0.24 0.563,0.438 0.313,0.198 10 false *a 4.604,0.5 4.917,0.698 0.313,0.198 10 false K62 0.76,2.604 1.073,2.802 0.313,0.198 10 false *b 4.104,2.604 4.417,2.802 0.313,0.198 10 false *c 2.708,2.323 3.24,2.573 0.531,0.25 10 false CLG2 3.188,2.323 3.719,2.573 0.531,0.25 10 false CG2B 5.417,2.281 5.708,2.49 0.292,0.208 10 false E 0.615,3.531 1.146,3.781 0.531,0.25 10 false GND 4.021,3.531 4.552,3.781 0.531,0.25 10 false GND 4.021,5.542 4.552,5.792 0.531,0.25 10 false GND 0.615,5.542 1.146,5.792 0.531,0.25 10 false GND 0.792,4.698 1.104,4.896 0.313,0.198 10 false *d 4.156,4.667 4.469,4.865 0.313,0.198 10 false *e 3.385,0.5 3.698,0.698 0.313,0.198 10 false R8
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
*b Waveform 1
*c Waveform 2 *d Waveform 3
*e Waveform 4 - -


a.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
R8-15 (CLG2) - K62-18 (E) Procedure:
1.

Power switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*)


5 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 1)
Procedure:
1.

Power switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)


5 V/DIV., 100 ms/DIV. Pulse generation
(See waveform 2)
R8-14 (CG2B) - K62-18 (E) Procedure:
1.

Power switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*)


5 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 3)
Procedure:
1.

Power switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)


5 V/DIV., 100 ms/DIV. Pulse generation
(See waveform 4)


*: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)