Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR › 2019.02–2021.02
RM33C0E _59 Vehicle Exterior _065469 DOOR / HATCH _0333680 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  DISASSEMBLY  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front door removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane Departure Alert System (w/ Steering Control) (Click here)
Parking Support Brake System*
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
·

Door window regulator sub-assembly

·

Door glass

·

Door glass run


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Remote control function

·

Key-linked function

·

Wireless transmitter-linked function

·

Key-off operation function

·

Catch protection function

·

Window open warning function


(Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 64718C 2.REMOVE LUGGAGE TRIM SERVICE HOLE COVER

Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>AUXILIARY BATTERY>REMOVAL

CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


Hide 67492A 4.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH

a.
B469203

Disengage the clip and guide to remove the front door lower frame bracket garnish.


Hide 74038A 5.REMOVE FRONT DOOR ARMREST COVER SUB-ASSEMBLY

a.
B469204

Using a moulding remover, disengage the 3 claws to remove the front door armrest cover sub-assembly.


Hide 6.REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

a.
B469205C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape to the front door trim board sub-assembly as shown in the illustration.


b.
B469206C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the clip, 7 claws and 5 guides as shown in the illustration.


c.
B471735C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the guide as shown in the illustration.


d.

Disconnect the connector to remove the multiplex network master switch assembly with front door upper armrest base panel.


Hide 7.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)

a.
B471719C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape to the front door trim board sub-assembly as shown in the illustration.


b.
B471720C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the clip, 7 claws and 5 guides as shown in the illustration.


c.
B471741C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the guide as shown in the illustration.


d.

Disconnect the connector to remove the power window regulator switch assembly with front door upper armrest base panel.


Hide 74220 8.REMOVE FRONT ARMREST ASSEMBLY

a.
B469208C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 3 clips, 8 claws and 3 guides as shown in the illustration.


b.
B469210C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the guide to remove the front armrest assembly as shown in the illustration.


Hide 81230 9.REMOVE COURTESY LIGHT ASSEMBLY

Hide 67602 10.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

a.
B469212C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape to the front door panel as shown in the illustration.


b.
B469213

Remove the 3 screws.


c.
B469216C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the 10 clips as shown in the illustration.


d.
B479793C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 7 claws and guide as shown in the illustration.


e.
B471431C01
2.24,1.219 2.615,0.948 true 2.125,1.635 2.365,1.906 true 2.625,0.823 2.854,1.01 0.229,0.188 10 true *1 2.385,1.844 2.615,2.031 0.229,0.188 10 true *2
*1 Front Door Inside Locking Cable Assembly
*2 Front Door Lock Remote Control Cable Assembly
V113147

Remove in this Direction


Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly to remove the front door trim board sub-assembly as shown in the illustration.


Hide 11.REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP WITH FRONT DOOR VENT SEAL

a.
B477384

Disengage the clip.


b.
B479792C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the front door inner glass weatherstrip with front door vent seal as shown in the illustration.


Hide 67838A 12.REMOVE FRONT DOOR VENT SEAL

a.
B479791C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the front door vent seal from the front door inner glass weatherstrip as shown in the illustration.


Hide 69206B 13.REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

B471434

a.

Disengage the 3 claws to remove the front door inside handle sub-assembly.


Hide 89430A 14.REMOVE OUTER MIRROR CONTROL ECU ASSEMBLY

Hide 87964 16.REMOVE OUTER MIRROR INSTALL HOLE COVER

Hide 17.REMOVE OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER

Hide 86160 18.REMOVE FRONT NO. 1 SPEAKER ASSEMBLY

Hide 67832 19.REMOVE FRONT DOOR SERVICE HOLE COVER

a.
B471435

Disengage the 2 clamps.


b.
B471436

Turn each front door weatherstrip clip 45 degrees and remove the 4 front door weatherstrip clips as shown in the illustration.


c.
B471437

Disengage the 3 clips to remove the front door service hole cover.


Hide 68102 21.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

a.
B471438

Remove the hole plug.


b.

for Driver Side:

i.

Connect the multiplex network master switch assembly.



c.

for Front Passenger Side:

i.

Connect the power window regulator switch assembly.



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG).


f.

Move the front door glass sub-assembly so that the door glass bolts can be seen.


g.

Turn the power switch on (IG).


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


i.

for Driver Side:

i.

Disconnect the multiplex network master switch assembly.



j.

for Front Passenger Side:

i.

Disconnect the power window regulator switch assembly.



k.
B471439

Remove the 2 bolts.

NOTICE:

After the bolts are removed, do not allow the front door glass sub-assembly to fall.



l.
B471440C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Remove the front door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.

NOTICE:

Do not damage the front door glass sub-assembly.



Hide 22.REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY

a.
B471441

Disengage the 2 claws to remove the front door No. 2 service hole cover.


b.
B471442C01
1.146,0.656 1.917,0.906 true 0.917,0.542 1.135,0.74 0.219,0.198 10 true *a
*a Temporary Bolt


Disconnect the connector.


c.

Loosen the temporary bolt.

NOTICE:

Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator assembly may fall and cause damage.



d.

Remove the 5 bolts.


e.

Remove the front door window regulator assembly.


f.

Remove the temporary bolt from the front door window regulator assembly.


Hide 67856B 23.REMOVE FRONT DOOR PANEL PROTECTOR

a.
B471722

Remove the front door panel protector.


Hide 68151C 24.REMOVE FRONT DOOR GLASS RUN

a.
B471443

Remove the front door glass run.


Hide 67404F 25.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

a.
B471444C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the 2 bolts.


b.

Disengage the guide and remove the front door rear lower frame sub-assembly as shown in the illustration.


Hide 69220 26.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY

a.
B471448

Disengage the 2 claws.


b.

Using a screwdriver, disconnect the connector.


c.
B471450

Disengage the 3 clamps.


d.
B471451C01
0,0 0,0 false
V113147

Disengage in this Direction


Disengage the 2 claws and move the lever as shown in the illustration.


e.
B471453C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the front door outside handle assembly as shown in the illustration.


Hide 27.REMOVE FRONT DOOR LOCK CYLINDER ASSEMBLY (for Driver Side)

a.
B471455

Remove the hole plug.


b.
B471456

Using a T30 "TORX" socket wrench, loosen the screw and remove the front door lock cylinder assembly.


Hide 69217F 28.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)

a.
B471457

Remove the hole plug.


b.
B471458

Using a T30 "TORX" socket wrench, loosen the screw.


c.

Disengage the 2 guides and claw and remove the front door outside handle cover.


Hide 69241H 29.REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD

a.
B471459

Disengage the 3 claws to remove the front door front outside handle pad.


Hide 69242E 30.REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD

a.
B471460

Disengage the 3 guides and claw to remove the front door rear outside handle pad.


Hide 69040A 31.REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY

Hide 69202A 32.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.
B471461C01
0.052,0.052 0.375,0.323 0.323,0.271 12 true *A 0.052,2.302 0.427,2.583 0.375,0.281 12 true *B
*A Inside
*B Outside


Using a T30 "TORX" socket wrench, remove the screw.


b.

Slide the front door outside handle frame sub-assembly as shown in the illustration to disengage the claw and then remove the front door outside handle frame sub-assembly.


Hide 69312 33.REMOVE FRONT DOOR LOCK OPEN ROD

a.
B471462C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Remove the front door lock open rod as indicated by the arrows, in the order shown in the illustration.


Hide 68620 34.REMOVE FRONT DOOR CHECK ASSEMBLY

a.
B471464C01
0,0 0,0 false
V100135

Nut
V100136

Bolt


Remove the 2 nuts, bolt and front door check assembly.


Hide 67862 35.REMOVE FRONT DOOR WEATHERSTRIP

a.
B471469

Using a clip remover, disengage the 25 clips and remove the front door weatherstrip.


Hide 67664C 36.REMOVE DOOR FRAME GARNISH

a.
B471466

Disengage the 3 claws to remove the door frame garnish.


Hide 67402F 37.REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY

a.
B471446C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the 2 bolts.


b.

Disengage the guide and remove the front door front lower frame sub-assembly as shown in the illustration.


Hide 67001A 38.REMOVE FRONT DOOR PANEL CUSHION

a.
B481250

Disengage the 2 claws to remove the front door panel cushion.


Hide 67864B 39.REMOVE FRONT DOOR NO. 2 WEATHERSTRIP

a.
B471468

Disengage the 8 clips to remove the front door No. 2 weatherstrip.


Hide 75720 40.REMOVE FRONT DOOR BELT MOULDING ASSEMBLY

Hide 67496A 41.REMOVE FRONT DOOR FRONT LOWER FRAME UPPER COVER

Hide 75792 42.REMOVE DOOR WINDOW FRAME MOULDING CLIP

a.
B469803C01
0.646,1.479 1.229,0.969 true 0.479,1.427 0.792,1.625 0.313,0.198 10 false *a
*a Protective Tape
V113147

Remove in this Direction


Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws to remove the door window frame moulding clip.


Hide 75756C 43.REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING

Hide 67852D 44.REMOVE FRONT DOOR REAR OUTSIDE SEAL

a.
B471661

Disengage the guide to remove the front door rear outside seal.


Hide 75754A 45.REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING

Hide 75976G 46.REMOVE FRONT DOOR NO. 2 STRIPE

Hide 75986B 47.REMOVE FRONT DOOR NO. 3 STRIPE