Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE PEDAL (for RHD) › 2019.02–2021.08
RM33C0E _54 Brake _065443 BRAKE SYSTEM (OTHER) _0319350 BRAKE PEDAL(for RHD) N

BRAKE SYSTEM (OTHER)  BRAKE PEDAL(for RHD)  ADJUSTMENT  


PROCEDURE

Hide 1.INSPECT AND ADJUST BRAKE PEDAL HEIGHT

a.

Remove the front door scuff plate RH.

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL



b.

Remove the cowl side trim sub-assembly RH.

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL



c.

Remove the No. 1 instrument panel under cover sub-assembly.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL




f.

Check the brake pedal height.

HINT:

Inspect and adjust the brake pedal height with the floor carpet and front floor mat folded back.


i.

Measure the shortest distance between the brake pedal pad surface and floor panel as shown in the illustration.

C377992C02
2.104,2.5 2.104,2.042 true 4.854,2.917 5.125,2.917 5.125,2.917 5.521,2.458 true 6.083,1.656 6.333,1.323 6.333,1.323 6.573,1.323 false 3.208,3.083 3.208,2.625 true 2.031,2.51 2.219,2.667 0.188,0.156 10 true *1 3.042,2.104 3.219,2.26 0.177,0.156 10 true *a 3.156,3.115 3.323,3.271 0.167,0.156 10 true *b 1.281,1.573 1.479,1.729 0.198,0.156 10 true *c 6.615,1.25 6.927,1.406 0.313,0.156 10 false *1 6.177,2.302 6.49,2.458 0.313,0.156 10 false *a 4.688,2.854 5,3.01 0.313,0.156 10 false *b
*1 Brake Pedal Pad - -
*a Brake Pedal Height *b Measuring Plane of Floor Panel
*c 36 mm (1.42 in.) - -


Brake Pedal Height from Floor Panel:

149.5 to 159.5 mm (5.89 to 6.28 in.)


HINT:

If the brake pedal height is not as specified, inspect and adjust the push rod length according to the procedure below.




g.

Adjust the push rod length.

i.
C377994C02
2.125,1.792 2.125,1.094 2.125,1.094 2.344,1.094 false 2.792,1.885 2.792,1.625 2.792,1.625 3.01,1.625 false 2.385,3.813 2.167,4.094 2.167,4.094 1.875,4.094 true 3.052,1.563 3.365,1.719 0.313,0.156 10 false *1 2.385,1.031 2.698,1.188 0.313,0.156 10 false *2 1.708,4.021 2.021,4.177 0.313,0.156 10 false *a 3.01,3.688 3.323,3.844 0.313,0.156 10 false *b
*1 Stop Light Switch Assembly
*2 Lock Nut
*a Floor Panel
*b Brake Pedal Height


Remove the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


ii.

Loosen the lock nut.


iii.

Adjust the brake pedal height by turning the push rod.

Brake Pedal Height from Floor Panel:

149.5 to 159.5 mm (5.89 to 6.28 in.)



iv.

Tighten the lock nut.

Torque:
25.5 N*m (260 kgf*cm, 19 ft.*lbf)


v.

Install the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION





j.

Install the No. 1 instrument panel under cover sub-assembly.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>INSTALLATION


k.

Install the cowl side trim sub-assembly RH.

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION



l.

Install the front door scuff plate RH.

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION



Hide 89510D 2.INSPECT AND ADJUST BRAKE PEDAL STROKE SENSOR ASSEMBLY

a.

Inspect the brake pedal stroke sensor assembly.

i.

Connect the GTS to the DLC3 with the power switch off.


ii.

Turn the power switch on (IG).


iii.

Turn the GTS on and enter the following menus: Chassis / ABS/VSC/TRC / Data List / Stroke Sensor.

Chassis > ABS/VSC/TRC > Data List
Tester Display
Stroke Sensor
50003 105 11

iv.

Read the stroke sensor value without the brake pedal depressed.

Standard Voltage (without the brake pedal depressed):

0.8 to 1.2 V


HINT:

If the stroke sensor value is not within the standard voltage, adjust the brake pedal stroke sensor assembly.




b.

Adjust the brake pedal stroke sensor assembly.

i.

Remove the front door scuff plate RH.

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL



ii.

Remove the cowl side trim sub-assembly RH.

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL



iii.

Remove the No. 1 instrument panel under cover sub-assembly.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL


iv.
C376568

Loosen the 2 nuts.

NOTICE:

Do not depress the brake pedal after turning the power switch on (IG).



v.
C376569

Read the stroke sensor value in the Data List, and turn the brake pedal stroke sensor assembly slowly to the right or left to adjust the output voltage so that it is within the following range.

Standard Voltage (without the brake pedal depressed):

0.8 to 1.2 V



vi.

Tighten the 2 nuts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


vii.

Turn the GTS off and turn the power switch off.


viii.

Disconnect the GTS.


ix.

Install the No. 1 instrument panel under cover sub-assembly.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>INSTALLATION


x.

Install the cowl side trim sub-assembly RH.

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION



xi.

Install the front door scuff plate RH.

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION




c.

Perform linear solenoid valve offset learning, ABS holding solenoid valve learning, brake pedal stroke sensor assembly zero point calibration and system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


Hide 3.INSPECT BRAKE PEDAL FREE PLAY

a.
C132708C09
2.167,1.563 2.469,1.781 0.302,0.219 10 false *a
*a Brake Pedal Free Play


Depress the brake pedal until a slight resistance is felt. Measure the distance as shown in the illustration.

Brake Pedal Free Play:

1.0 to 6.0 mm (0.0394 to 0.236 in.)


HINT:
·

If the brake pedal free play is not as specified, check the stop light switch clearance.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION

·

If the brake pedal free play is as specified, proceed to the Inspect Brake Pedal Reserve Distance procedure.




Hide 4.INSPECT BRAKE PEDAL RESERVE DISTANCE

a.

With the power switch on (READY), depress the brake pedal and measure the brake pedal reserve distance.

C377993C02
2.198,2.49 2.198,2.083 true 3.156,3.104 3.156,2.625 true 4.99,2.823 5.302,2.823 5.302,2.823 5.542,2.448 true 6.156,1.458 5.896,1.458 5.896,1.458 5.729,1.76 false 2.135,2.5 2.313,2.656 0.177,0.156 10 true *1 3.052,2.135 3.229,2.292 0.177,0.156 10 true *a 3.083,3.135 3.26,3.292 0.177,0.156 10 true *b 1.302,1.604 1.5,1.75 0.198,0.146 10 true *c 6.198,1.396 6.51,1.552 0.313,0.156 10 false *1 6.094,2.438 6.406,2.594 0.313,0.156 10 false *a 4.833,2.771 5.146,2.927 0.313,0.156 10 false *b
*1 Brake Pedal Pad - -
*a Brake Pedal Reserve Distance *b Measuring Plane of Floor Panel
*c 36 mm (1.42 in.) - -


Brake Pedal Reserve Distance from Floor Panel at 300 N (31 kgf, 67.4 lbf):

85 mm (3.35 in.) or more


HINT:
·

Measure the distance at the same point used for the brake pedal height inspection.

·

If the distance is not as specified, troubleshoot the brake system.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE