Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING SUPPORT BRAKE SYSTEM › 2019.02–2021.02
RM33C0E _56 Audio / Visual / Telematics _065452 PARK ASSIST / MONITORING _0387691 PARKING SUPPORT BRAKE SYSTEM C

PARK ASSIST / MONITORING  PARKING SUPPORT BRAKE SYSTEM  C164B  Communication Error From Clearance Sonar ECU to VSC  


DESCRIPTION

The electronically controlled brake system receives parking support brake system information from the clearance warning ECU assembly via CAN communication. When it is determined that there is a communication error between the skid control ECU and clearance warning ECU assembly, DTC C164B is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C164B Communication Error From Clearance Sonar ECU to VSC A communication error between the skid control ECU and clearance warning ECU assembly is detected
·

Clearance warning ECU assembly

·

Electronically controlled brake system

·

Skid control ECU



CAUTION / NOTICE / HINT

NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After replacing an ultrasonic sensor or the clearance warning ECU assembly, perform the necessary procedures (adjustment, calibration, initialization or registration).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING SUPPORT BRAKE SYSTEM>CALIBRATION



PROCEDURE

1.CHECK DTC OUTPUT
a.

Using the GTS, check for DTCs according to the prompts on the screen.

HINT:

After turning the power switch from off to on (IG), wait 4 seconds or more before checking for DTCs.


Body Electrical > IPA/ICS/Clearance Sonar > Trouble Codes
50001 170

b.

Clear the DTCs according to the screen on the GTS.

Body Electrical > IPA/ICS/Clearance Sonar > Clear DTCs
50002 170

c.

Recheck for DTCs.

Body Electrical > IPA/ICS/Clearance Sonar > Trouble Codes
50001 170
HINT:
·

If DTC C164B is not output after clearing the DTCs, an intermittent communication error between the clearance warning ECU assembly and skid control ECU is suspected.

·

If DTC C164B is output frequently, duplicate the conditions that cause the problem symptoms and perform the inspection again, even though the DTC was not output when rechecking for DTCs.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING




Result:
Result Proceed to
DTC C164B is output A
DTC C164B is not output B



A

2.CHECK DTC OUTPUT (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)

B

2.CHECK DTC OUTPUT (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)
a.

Using the GTS, check for DTCs according to the prompts on the screen.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC is not output A
DTC is output B



A

3.REPLACE CLEARANCE WARNING ECU ASSEMBLY

B

3.REPLACE CLEARANCE WARNING ECU ASSEMBLY

Result:
Proceed to
NEXT



NEXT

4.CHECK DTC OUTPUT
4.CHECK DTC OUTPUT
a.

Using the GTS, check for DTCs according to the prompts on the screen.

Body Electrical > IPA/ICS/Clearance Sonar > Trouble Codes
50001 170

b.

Clear the DTCs according to the screen on the GTS.

Body Electrical > IPA/ICS/Clearance Sonar > Clear DTCs
50002 170

c.

Recheck for DTCs.

Body Electrical > IPA/ICS/Clearance Sonar > Trouble Codes
50001 170

Result:
Result Proceed to
DTC C164B is output A
DTC C164B is not output B



A

B

END (CLEARANCE WARNING ECU ASSEMBLY DEFECTIVE)