Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM (w/ Parking Support Brake System) › 2019.02–2021.02
RM33C0E _56 Audio / Visual / Telematics _065452 PARK ASSIST / MONITORING _0387692 TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/ Parking Support Brake System) C

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/ Parking Support Brake System)  C1AEC  Front Sensor Communication Malfunction  


DESCRIPTION

This DTC is stored when there is an open or short circuit in the communication line between the front sensors and the ECU, or when there is a malfunction in a front sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AEC Front Sensor Communication Malfunction An open or short circuit in the communication line between the front sensors and ECU or a malfunction in a front sensor during initialization mode after the power switch is turned on (IG).
·

Front ultrasonic sensor circuit

·

Harness or connector

·

Clearance warning ECU assembly



WIRING DIAGRAM

E410481E10
0.188,3.938 1.917,4.292 1.729,0.354 10 false Front Center Ultrasonic Sensor RH 3.823,0.958 4.031,1.323 0.208,0.365 10 false BI 3.844,1.302 4.052,1.573 0.208,0.271 10 false EI 3.844,0.573 4.042,0.896 0.198,0.323 10 false SI 3.167,0.927 3.5,1.25 0.333,0.323 10 false BO 3.156,1.313 3.469,1.552 0.313,0.24 10 false EO 3.156,0.552 3.448,0.771 0.292,0.219 10 false SO 1.313,0.958 1.573,1.25 0.26,0.292 10 false BI 1.302,1.313 1.521,1.531 0.219,0.219 10 false EI 1.313,0.573 1.531,0.813 0.219,0.24 10 false SI 1.24,3.083 1.458,3.302 0.219,0.219 10 false BO 1.25,3.458 1.521,3.667 0.271,0.208 10 false EO 1.25,2.719 1.5,2.938 0.25,0.219 10 false SO 5.688,3.448 5.917,3.708 0.229,0.26 10 false EI 5.688,2.698 5.938,2.917 0.25,0.219 10 false SI 5.698,3.063 5.948,3.365 0.25,0.302 10 false BI 4.094,0.427 4.25,0.583 0.156,0.156 10 false 5 2.938,0.823 3.042,0.979 0.104,0.156 10 false 1 2.927,0.427 3.083,0.573 0.156,0.146 10 false 2 4.104,1.219 4.26,1.375 0.156,0.156 10 false 6 4.094,0.823 4.25,0.979 0.156,0.156 10 false 4 2.927,1.24 3.073,1.396 0.146,0.156 10 false 3 1.552,0.427 1.708,0.583 0.156,0.156 10 false 5 1.552,2.958 1.708,3.115 0.156,0.156 10 false 1 1.552,2.573 1.708,2.729 0.156,0.156 10 false 2 1.552,1.24 1.708,1.396 0.156,0.156 10 false 6 1.542,0.823 1.698,0.979 0.156,0.156 10 false 4 1.552,3.375 1.708,3.531 0.156,0.156 10 false 3 5.479,2.573 5.583,2.729 0.104,0.156 10 false 5 5.479,3.375 5.583,3.531 0.104,0.156 10 false 6 5.469,2.969 5.604,3.135 0.135,0.167 10 false 4 3.156,3.063 3.365,3.302 0.208,0.24 10 false BI 3.167,3.469 3.385,3.76 0.219,0.292 10 false EI 3.156,2.688 3.344,2.938 0.188,0.25 10 false SI 3.802,3.094 4.125,3.396 0.323,0.302 10 false BO 3.792,3.458 4.042,3.74 0.25,0.281 10 false EO 3.792,2.719 4.083,2.99 0.292,0.271 10 false SO 4.104,2.573 4.26,2.729 0.156,0.156 10 false 2 2.969,2.958 3.073,3.115 0.104,0.156 10 false 4 2.969,2.563 3.073,2.719 0.104,0.156 10 false 5 4.104,3.375 4.26,3.531 0.156,0.156 10 false 3 4.104,2.958 4.26,3.115 0.156,0.156 10 false 1 2.969,3.375 3.073,3.531 0.104,0.156 10 false 6 2.771,3.76 3.031,3.927 0.26,0.167 10 false B9 0.198,3.76 0.49,3.927 0.292,0.167 10 false B8 5.531,1.833 6.76,2.167 1.229,0.333 10 false Clearance Warning ECU Assembly 5.677,0.958 6.115,1.24 0.438,0.281 10 false BOF 5.688,1.313 6.115,1.563 0.427,0.25 10 false E5 5.677,0.563 6.073,0.844 0.396,0.281 10 false SOF 5.438,0.438 5.625,0.583 0.188,0.146 10 false 8 5.438,1.24 5.615,1.396 0.177,0.156 10 false 6 5.438,0.833 5.615,0.99 0.177,0.156 10 false 4 5.51,1.688 5.802,1.854 0.292,0.167 10 false R39 5.354,3.76 5.625,3.927 0.271,0.167 10 false B10 2.771,1.823 4.271,2.156 1.5,0.333 10 false Front Corner Ultrasonic Sensor RH 2.771,1.646 3.031,1.813 0.26,0.167 10 false B7 2.792,3.917 4.521,4.271 1.729,0.354 10 false Front Center Ultrasonic Sensor LH 5.333,3.927 6.833,4.26 1.5,0.333 10 false Front Corner Ultrasonic Sensor LH


PROCEDURE

1.INITIALIZE FRONT CENTER ULTRASONIC SENSOR AND FRONT CORNER ULTRASONIC SENSOR
a.

Initialize the front center ultrasonic sensor and front corner ultrasonic sensor.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING SUPPORT BRAKE SYSTEM>CALIBRATION


Result:
Proceed to
NEXT



NEXT

2.CHECK DTC OUTPUT (C1AEC)
2.CHECK DTC OUTPUT (C1AEC)
a.

Check for DTCs.

Body Electrical > IPA/ICS/Clearance Sonar > Trouble Codes
50001 170

b.

Clear the DTCs.

Body Electrical > IPA/ICS/Clearance Sonar > Clear DTCs
50002 170

c.

Recheck for DTCs.

Body Electrical > IPA/ICS/Clearance Sonar > Trouble Codes
50001 170

Result:
Result Proceed to
DTC C1AEC is output A
No DTCs are output B



A

3.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - FRONT CORNER ULTRASONIC SENSOR RH)

B

3.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - FRONT CORNER ULTRASONIC SENSOR RH)
a.

Disconnect the R39 clearance warning ECU assembly connector.


b.

Disconnect the B7 front corner ultrasonic sensor RH.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R39-4 (BOF) - B7-4 (BI) Always Below 1 Ω
R39-8 (SOF) - B7-5 (SI) Always Below 1 Ω
R39-6 (E5) - B7-6 (EI) Always Below 1 Ω
R39-4 (BOF) or B7-4 (BI) - Body ground Always 10 kΩ or higher
R39-8 (SOF) or B7-5 (SI) - Body ground Always 10 kΩ or higher
R39-6 (E5) or B7-6 (EI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (FRONT CORNER ULTRASONIC SENSOR RH - FRONT CENTER ULTRASONIC SENSOR RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (FRONT CORNER ULTRASONIC SENSOR RH - FRONT CENTER ULTRASONIC SENSOR RH)
a.

Disconnect the B8 front center ultrasonic sensor RH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B7-1 (BO) - B8-4 (BI) Always Below 1 Ω
B7-2 (SO) - B8-5 (SI) Always Below 1 Ω
B7-3 (EO) - B8-6 (EI) Always Below 1 Ω
B7-1 (BO) or B8-4 (BI) - Body ground Always 10 kΩ or higher
B7-2 (SO) or B8-5 (SI) - Body ground Always 10 kΩ or higher
B7-3 (EO) or B8-6 (EI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (FRONT CENTER ULTRASONIC SENSOR RH - FRONT CENTER ULTRASONIC SENSOR LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (FRONT CENTER ULTRASONIC SENSOR RH - FRONT CENTER ULTRASONIC SENSOR LH)
a.

Disconnect the B9 front center ultrasonic sensor LH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B8-1 (BO) - B9-4 (BI) Always Below 1 Ω
B8-2 (SO) - B9-5 (SI) Always Below 1 Ω
B8-3 (EO) - B9-6 (EI) Always Below 1 Ω
B8-1 (BO) or B9-4 (BI) - Body ground Always 10 kΩ or higher
B8-2 (SO) or B9-5 (SI) - Body ground Always 10 kΩ or higher
B8-3 (EO) or B9-6 (EI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (FRONT CENTER ULTRASONIC SENSOR LH - FRONT CORNER ULTRASONIC SENSOR LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (FRONT CENTER ULTRASONIC SENSOR LH - FRONT CORNER ULTRASONIC SENSOR LH)
a.

Disconnect the B10 front corner ultrasonic sensor LH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B9-1 (BO) - B10-4 (BI) Always Below 1 Ω
B9-2 (SO) - B10-5 (SI) Always Below 1 Ω
B9-3 (EO) - B10-6 (EI) Always Below 1 Ω
B9-1 (BO) or B10-4 (BI) - Body ground Always 10 kΩ or higher
B9-2 (SO) or B10-5 (SI) - Body ground Always 10 kΩ or higher
B9-3 (EO) or B10-6 (EI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT FRONT CORNER ULTRASONIC SENSOR RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT FRONT CORNER ULTRASONIC SENSOR RH
a.
E332147C01
0.938,0.833 1.375,1.115 true 1.573,0.583 1.729,1.104 true 2.344,0.76 2,1.146 true 2.188,1.833 2,1.448 true 1.604,1.854 1.75,1.438 true 1.063,1.802 1.385,1.438 true 0.104,0.188 0.417,0.344 0.313,0.156 10 false *a 0.719,0.677 1.031,0.833 0.313,0.156 10 false EO 1.479,0.396 1.792,0.552 0.313,0.156 10 false SO 2.302,0.594 2.615,0.75 0.313,0.156 10 false BO 0.979,1.854 1.292,2.01 0.313,0.156 10 false EI 1.542,1.906 1.854,2.063 0.313,0.156 10 false SI 2.167,1.885 2.479,2.042 0.313,0.156 10 false BI
*a Component without harness connected
(Front Corner Ultrasonic Sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (BI) - 6 (EI) Always 10 kΩ or higher
4 (BI) - 1 (BO) Always Below 1 Ω
5 (SI) - 2 (SO) Always Below 30 Ω
6 (EI) - 3 (EO) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.INSPECT FRONT CENTER ULTRASONIC SENSOR RH

NG

8.INSPECT FRONT CENTER ULTRASONIC SENSOR RH
a.
E332147C01
0.938,0.833 1.375,1.115 true 1.573,0.583 1.729,1.104 true 2.344,0.76 2,1.146 true 2.188,1.833 2,1.448 true 1.604,1.854 1.75,1.438 true 1.063,1.802 1.385,1.438 true 0.104,0.188 0.417,0.344 0.313,0.156 10 false *a 0.719,0.677 1.031,0.833 0.313,0.156 10 false EO 1.479,0.396 1.792,0.552 0.313,0.156 10 false SO 2.302,0.594 2.615,0.75 0.313,0.156 10 false BO 0.979,1.854 1.292,2.01 0.313,0.156 10 false EI 1.542,1.906 1.854,2.063 0.313,0.156 10 false SI 2.167,1.885 2.479,2.042 0.313,0.156 10 false BI
*a Component without harness connected
(Front Center Ultrasonic Sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (BI) - 6 (EI) Always 10 kΩ or higher
4 (BI) - 1 (BO) Always Below 1 Ω
5 (SI) - 2 (SO) Always Below 30 Ω
6 (EI) - 3 (EO) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.INSPECT FRONT CENTER ULTRASONIC SENSOR LH

NG

9.INSPECT FRONT CENTER ULTRASONIC SENSOR LH
a.
E332147C01
0.938,0.833 1.375,1.115 true 1.573,0.583 1.729,1.104 true 2.344,0.76 2,1.146 true 2.188,1.833 2,1.448 true 1.604,1.854 1.75,1.438 true 1.063,1.802 1.385,1.438 true 0.104,0.188 0.417,0.344 0.313,0.156 10 false *a 0.719,0.677 1.031,0.833 0.313,0.156 10 false EO 1.479,0.396 1.792,0.552 0.313,0.156 10 false SO 2.302,0.594 2.615,0.75 0.313,0.156 10 false BO 0.979,1.854 1.292,2.01 0.313,0.156 10 false EI 1.542,1.906 1.854,2.063 0.313,0.156 10 false SI 2.167,1.885 2.479,2.042 0.313,0.156 10 false BI
*a Component without harness connected
(Front Center Ultrasonic Sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (BI) - 6 (EI) Always 10 kΩ or higher
4 (BI) - 1 (BO) Always Below 1 Ω
5 (SI) - 2 (SO) Always Below 30 Ω
6 (EI) - 3 (EO) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.INSPECT FRONT CORNER ULTRASONIC SENSOR LH

NG

10.INSPECT FRONT CORNER ULTRASONIC SENSOR LH
a.
E332147C18
2.188,1.833 2,1.448 true 1.604,1.854 1.75,1.438 true 1.063,1.802 1.385,1.438 true 0.104,0.188 0.417,0.344 0.313,0.156 10 false *a 0.979,1.854 1.292,2.01 0.313,0.156 10 false EI 1.542,1.906 1.854,2.063 0.313,0.156 10 false SI 2.167,1.885 2.479,2.042 0.313,0.156 10 false BI
*a Component without harness connected
(Front Corner Ultrasonic Sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (BI) - 6 (EI) Always 10 kΩ or higher
4 (BI) - 1 Always Below 1 Ω
5 (SI) - 2 Always Below 30 Ω
6 (EI) - 3 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

11.REPLACE FRONT CORNER ULTRASONIC SENSOR RH

NG

11.REPLACE FRONT CORNER ULTRASONIC SENSOR RH

NEXT

12.CHECK DTC OUTPUT (C1AEC)
12.CHECK DTC OUTPUT (C1AEC)
a.

Clear the DTCs.

Body Electrical > IPA/ICS/Clearance Sonar > Clear DTCs
50002 170

b.

Check for DTCs.

Body Electrical > IPA/ICS/Clearance Sonar > Trouble Codes
50001 170

Result:
Result Proceed to
DTC C1AEC is output A
No DTCs are output B



A

13.REPLACE FRONT CENTER ULTRASONIC SENSOR RH

B

END (FRONT CORNER ULTRASONIC SENSOR RH WAS DEFECTIVE)

13.REPLACE FRONT CENTER ULTRASONIC SENSOR RH

NEXT

14.CHECK DTC OUTPUT (C1AEC)
14.CHECK DTC OUTPUT (C1AEC)
a.

Clear the DTCs.

Body Electrical > IPA/ICS/Clearance Sonar > Clear DTCs
50002 170

b.

Check for DTCs.

Body Electrical > IPA/ICS/Clearance Sonar > Trouble Codes
50001 170

Result:
Result Proceed to
DTC C1AEC is output A
No DTCs are output B



A

15.REPLACE FRONT CENTER ULTRASONIC SENSOR LH

B

END (FRONT CENTER ULTRASONIC SENSOR RH WAS DEFECTIVE)

15.REPLACE FRONT CENTER ULTRASONIC SENSOR LH

NEXT

16.CHECK DTC OUTPUT (C1AEC)
16.CHECK DTC OUTPUT (C1AEC)
a.

Clear the DTCs.

Body Electrical > IPA/ICS/Clearance Sonar > Clear DTCs
50002 170

b.

Check for DTCs.

Body Electrical > IPA/ICS/Clearance Sonar > Trouble Codes
50001 170

Result:
Result Proceed to
DTC C1AEC is output A
No DTCs are output B



A

17.REPLACE FRONT CORNER ULTRASONIC SENSOR LH

B

END (FRONT CENTER ULTRASONIC SENSOR LH WAS DEFECTIVE)

17.REPLACE FRONT CORNER ULTRASONIC SENSOR LH

NEXT

18.CHECK DTC OUTPUT (C1AEC)
18.CHECK DTC OUTPUT (C1AEC)
a.

Clear the DTCs.

Body Electrical > IPA/ICS/Clearance Sonar > Clear DTCs
50002 170

b.

Check for DTCs.

Body Electrical > IPA/ICS/Clearance Sonar > Trouble Codes
50001 170

Result:
Result Proceed to
DTC C1AEC is output A
No DTCs are output B



A

B

END (FRONT CORNER ULTRASONIC SENSOR LH WAS DEFECTIVE)