The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during ultrasonic sensor removal/installation are shown below.
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
1.REMOVE FRONT BUMPER ASSEMBLY
89341K
2.REMOVE FRONT CORNER ULTRASONIC SENSOR (w/o Parking Support Brake System)
for Bar Type Radiator Grille:
|
Remove in this Direction |
Disconnect the connector.
Disengage the claw as shown in the illustration.
|
Remove in this Direction |
Disengage the 2 claws and remove the front corner ultrasonic sensor as shown in the illustration.
for Mesh Type Radiator Grille:
Disconnect the connector.
|
Remove in this Direction |
Disengage the 2 claws and remove the front corner ultrasonic sensor as shown in the illustration.
89348J
3.REMOVE ULTRASONIC SENSOR CLIP (w/o Parking Support Brake System)
Perform this procedure only when replacement of the ultrasonic sensor clip is necessary.
for Bar Type Radiator Grille:
Disengage the clamp to remove the ultrasonic sensor clip from the wire.
89347B
4.REMOVE FRONT CORNER ULTRASONIC SENSOR RETAINER (w/o Parking Support Brake System)
Perform this procedure only when replacement of the front corner ultrasonic sensor retainer is necessary.
When removing the front corner ultrasonic sensor retainer, heat the front bumper assembly and front corner ultrasonic sensor retainer using a heat light.
Heat the front bumper assembly and front corner ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.
| Item | Temperature |
|---|---|
| Front Bumper Assembly | 40 to 60°C (104 to 140°F) |
| Front Corner Ultrasonic Sensor Retainer |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
for Bar Type Radiator Grille:
Remove the front corner ultrasonic sensor retainer.
for Mesh Type Radiator Grille:
Remove the front corner ultrasonic sensor retainer.
89341L
5.REMOVE FRONT CENTER ULTRASONIC SENSOR (w/ Parking Support Brake System)
Disconnect the connector.
|
Remove in this Direction |
Disengage the 2 claws and remove the front center ultrasonic sensor as shown in the illustration.
89341K
6.REMOVE FRONT CORNER ULTRASONIC SENSOR (w/ Parking Support Brake System)
|
Remove in this Direction |
Disconnect the connector.
Disengage the 4 claws as shown in the illustration.
|
Remove in this Direction |
Disengage the 2 claws and remove the front corner ultrasonic sensor as shown in the illustration.
89348J
7.REMOVE ULTRASONIC SENSOR CLIP (w/ Parking Support Brake System)
Perform this procedure only when replacement of the ultrasonic sensor clip is necessary.
Disengage the clamp to remove the ultrasonic sensor clip from the wire.
89347C
8.REMOVE FRONT CENTER ULTRASONIC SENSOR RETAINER (w/ Parking Support Brake System)
Perform this procedure only when replacement of the front center ultrasonic sensor retainer is necessary.
When removing the front center ultrasonic sensor retainer, heat the front bumper assembly and front center ultrasonic sensor retainer using a heat light.
Heat the front bumper assembly and front center ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.
| Item | Temperature |
|---|---|
| Front Bumper Assembly | 40 to 60°C (104 to 140°F) |
| Front Center Ultrasonic Sensor Retainer |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Remove the front center ultrasonic sensor retainer.
89347B
9.REMOVE FRONT CORNER ULTRASONIC SENSOR RETAINER (w/ Parking Support Brake System)
Perform this procedure only when replacement of the front corner ultrasonic sensor retainer is necessary.
When removing the front corner ultrasonic sensor retainer, heat the front bumper assembly and front corner ultrasonic sensor retainer using a heat light.
Heat the front bumper assembly and front corner ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.
| Item | Temperature |
|---|---|
| Front Bumper Assembly | 40 to 60°C (104 to 140°F) |
| Front Corner Ultrasonic Sensor Retainer |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Remove the front corner ultrasonic sensor retainer.
89305
10.REMOVE ULTRASONIC SENSOR CUSHION SET
Only perform this procedure when removing and installing the ultrasonic sensor cushion set.
Remove the ultrasonic sensor cushion set as shown in the illustration.
|
Remove in this Direction | - | - |