Home › General › MAINTENANCE › FRONT DISC BRAKE PAD (for 2-Pot Caliper) › from 2019.02
RM33C0E _V1 General _065432 MAINTENANCE _0388016 FRONT DISC BRAKE PAD(for 2-Pot Caliper) A

MAINTENANCE  FRONT DISC BRAKE PAD(for 2-Pot Caliper)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the front disc brake pads, the brake pedal may feel soft due to clearance between the front disc brake pads and front disc. Depress the brake pedal several times until the brake pedal feels firm.

·

After replacing the front disc brake pads, always perform a road test to check the braking performance and check for vibrations.

·

When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be stored. As there is no malfunction, clear the DTC.

·

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 04945 1.INSTALL FRONT DISC BRAKE ANTI-SQUEAL SHIM KIT

NOTICE:
·

When replacing worn front disc brake pads, the front disc brake anti-squeal shims and front disc brake pad wear indicator plates must be replaced together with the front disc brake pads.

·

Install the front disc brake pad wear indicator plates in the correct position and direction.

·

Install the front disc brake anti-squeal shims in the correct position and direction.



a.
C342418C02
0.302,1.5 0.302,1.135 false 0.802,1.688 0.802,1.323 false 1.479,0.219 1.479,0.146 1.479,0.146 2.281,0.146 false 2.104,0.458 2.104,0.146 false 2.625,1.052 2.625,0.542 2.625,0.542 2.75,0.542 false 3.115,1.219 3.115,0.813 3.115,0.813 3.208,0.813 false 0.75,1.719 1.063,1.875 0.313,0.156 10 false *1 0.25,1.531 0.563,1.688 0.313,0.156 10 false *2 2.323,0.063 2.635,0.219 0.313,0.156 10 false *3 2.781,0.458 3.094,0.615 0.313,0.156 10 false *1 3.24,0.729 3.427,0.958 0.188,0.229 10 false *2
*1 Front No. 1 Disc Brake Anti-squeal Shim
*2 Front No. 2 Disc Brake Anti-squeal Shim
*3 Front Disc Brake Pad Wear Indicator Plate


Install the front No. 1 disc brake anti-squeal shim and front No. 2 disc brake anti-squeal shim to each front disc brake pad.


b.

Install the front disc brake pad wear indicator plate to each front disc brake pad.


Hide 2.INSTALL FRONT DISC BRAKE PAD

CAUTION:
·

Be careful not to get pinched by the front disc brake cylinder assembly or other parts when installing the front disc brake pads.

·
C380042

After lifting up the front disc brake cylinder assembly, secure it in place before performing any work on it.

·

The front disc brake cylinder assembly could fall, pinching hands or fingers and causing injury.



a.

Push in the front disc brake pistons.

NOTICE:
·

Make sure that the brake fluid does not overflow from the reservoir.

·

Do not forcibly push in the front disc brake pistons.




b.

Install the 2 front disc brake pads to the front disc brake cylinder mounting.

NOTICE:
·

Keep the friction surfaces of the front disc brake pads and front disc free from oil and grease.

·

Install the front disc brake pad so that the pad wear indicator plate is mounted on the upper side of the vehicle.




c.

Install the 2 anti-squeal springs to the front disc brake pads.

NOTICE:
·

When replacing the front disc brake pads with new ones, make sure to replace the anti-squeal springs at the same time.

·

Be sure to install the anti-squeal springs into the front disc brake pad installation holes as far as they will go.




d.

Hold the front disc brake cylinder slide pin (lower side) and install the front disc brake cylinder assembly to the front disc brake cylinder mounting with the bolt.

Torque:
34.3 N*m (350 kgf*cm, 25 ft.*lbf)

NOTICE:
·

Install the front disc brake cylinder assembly while holding both of the front disc brake pads because the anti-squeal springs may fall off the front disc brake pads.

·

Be sure that the anti-squeal springs are installed to the front disc brake pads.




Hide 3.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

a.

Connect the reservoir level switch connector.


b.

Connect the cable to the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>AUXILIARY BATTERY>INSTALLATION


c.

Turn the power switch on (READY).


d.

Depress the brake pedal and release it.



Hide 4.INSPECT BRAKE FLUID LEVEL IN RESERVOIR

Hide 5.INSTALL FRONT WHEEL