Home › Suspension › FRONT SUSPENSION › FRONT STABILIZER BAR › 2019.02–2020.08
RM33C0E _53 Suspension _065438 FRONT SUSPENSION _0334231 FRONT STABILIZER BAR A

FRONT SUSPENSION  FRONT STABILIZER BAR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front stabilizer bar removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Departure Alert System (w/ Steering Control) (Click here)
Parking Support Brake System*
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Replacement of ECM Vehicle Identification Number (VIN) or frame number registration MIL illuminates w/ Canister Pump Module:(Click here)
w/o Canister Pump Module:(Click here)
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired

·

Replacement of air fuel ratio sensor (sensor 2)


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


w/ Canister Pump Module:(Click here)
w/o Canister Pump Module:
(Click here)
Replacement of inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)
Replacement of hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Rear television camera assembly optical axis (Back camera position setting) Parking Assist Monitor System (Click here)
·

Suspension, tires, etc.

(The vehicle height changes because of suspension or tire replacement)

·

Replacement of front bumper assembly


·

Measure ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Replacement of headlight ECU sub-assembly LH
·

Synchronize the vehicle information

·

Perform headlight ECU sub-assembly LH initialization


Lighting System (EXT) (w/ Automatic Headlight Beam Level Control System) (Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Perform headlight ECU sub-assembly LH initialization
Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Rack and pinion power steering gear assembly
·

Perform torque sensor zero point calibration

·

Assist Map Writing


·

DTCs are output

·

Steering effort different between turning steering wheel left and right

·

EPS warning light illuminates


(Click here)

PROCEDURE

Hide 1.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

Hide 48810 2.REMOVE FRONT STABILIZER LINK ASSEMBLY LH

a.
C400795

Remove the cap from the nut.


b.
C373247

Remove the nut and front stabilizer link assembly LH from the front stabilizer bar.

NOTICE:

Do not damage the boot of the ball joint.


HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon socket wrench to hold the stud bolt.



Hide 48820B 3.REMOVE FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48829A 4.REMOVE FRONT NO. 1 STABILIZER BRACKET LH

a.
C373248

Remove the 2 bolts and front No. 1 stabilizer bracket LH from the front frame assembly.


Hide 48824A 5.REMOVE FRONT NO. 1 STABILIZER BRACKET RH

HINT:

Perform the same procedure as for the LH side.


Hide 48811 6.REMOVE FRONT STABILIZER BAR

a.

Remove the front stabilizer bar with 2 front stabilizer bar bushings from the front frame assembly.


Hide 48815 7.REMOVE FRONT NO. 1 STABILIZER BAR BUSHING (for LH Side)

a.

Remove the front No. 1 stabilizer bar bushing from the front stabilizer bar.


Hide 48815 8.REMOVE FRONT NO. 1 STABILIZER BAR BUSHING (for RH Side)

HINT:

Perform the same procedure as for the LH side.