Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT AXLE HUB BOLT › 2019.02–2021.02
RM33C0E _52 Drivetrain _065436 AXLE AND DIFFERENTIAL _0334217 FRONT AXLE HUB BOLT A

AXLE AND DIFFERENTIAL  FRONT AXLE HUB BOLT  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front axle hub bolt removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Departure Alert System (w/ Steering Control) (Click here)
Parking Support Brake System*
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)

NOTICE:
·

When removing or installing the front disc brake caliper assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C1214 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this step.

·

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISABLE BRAKE CONTROL

Hide 3.REMOVE FRONT WHEEL

Hide 47313J 4.SEPARATE FRONT FLEXIBLE HOSE

a.
C369722

Remove the bolt and separate the front flexible hose from the front shock absorber assembly.


Hide 5.SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY

a.

Remove the 2 bolts and separate the front disc brake caliper assembly from the steering knuckle.

NOTICE:

Use wire or an equivalent tool to keep the front disc brake caliper assembly from hanging by the front flexible hose.



Hide 43512 6.REMOVE FRONT DISC

Hide 43502D 7.REMOVE FRONT AXLE HUB BOLT

a.
C369718C01
1.854,1.01 1.854,0.219 1.854,0.219 2.031,0.219 true 2.365,0.865 3.01,0.865 3.01,0.865 3.01,1.354 true 2.604,1.063 3.01,1.063 true 2.958,1.385 3.271,1.542 0.313,0.156 10 false *a 2.073,0.135 2.365,0.302 0.292,0.167 10 true SST
*a Service Nut


Temporarily install 2 service nuts to the front axle hub bolts as shown in the illustration.

Recommended Service Nut:

Thread diameter: 12.0 mm (0.472 in.)

Thread pitch: 1.5 mm (0.0591 in.)


NOTICE:

Install the service nuts to prevent damage to the front axle hub bolts.



b.

Using SST and a screwdriver or an equivalent tool to hold the front axle hub sub-assembly, remove the front axle hub bolt.

SST
09611-12010  

NOTICE:

Do not damage the threads of the front axle hub bolts.



Hide 43502D 8.INSTALL FRONT AXLE HUB BOLT

a.

Temporarily install a new front axle hub bolt to the front axle hub sub-assembly.


b.
C369719C01
0.896,0.469 1.646,0.469 true 0.635,1.594 0.635,0.833 true 1.677,0.375 1.865,0.552 0.188,0.177 10 true *a 0.594,1.625 0.906,1.781 0.313,0.156 10 false *b
*a Service Nut
*b Washer


Install a washer and service nut to the front axle hub bolt as shown in the illustration.

Recommended Service Nut:

Thread diameter: 12.0 mm (0.472 in.)

Thread pitch: 1.5 mm (0.0591 in.)


HINT:

Recommended washer thickness is 5 mm (0.197 in.) or more.



c.

Using a screwdriver or an equivalent tool to hold the front axle hub sub-assembly, install the front axle hub bolt by tightening the service nut.

NOTICE:
·

Install the service nuts to prevent damage to the front axle hub bolts.

·

Do not damage the threads of the front axle hub bolts.




d.

Remove the 3 service nuts and washer from the 3 front axle hub bolts.


Hide 43512 9.INSTALL FRONT DISC

Hide 10.INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY

a.

Install the front disc brake caliper assembly to the steering knuckle with the 2 bolts.

Torque:
107 N*m (1091 kgf*cm, 79 ft.*lbf)

NOTICE:
·

Do not twist the front flexible hose when installing the front disc brake caliper assembly.

·

Make sure that there is no foreign matter on the threads of the bolt.




Hide 47313J 11.INSTALL FRONT FLEXIBLE HOSE

a.
C369729C01
0,0 0,0 false
V100135

Hook


Engage the 2 hooks to install the front speed sensor clamp bracket.

NOTICE:

Do not twist the front speed sensor when installing it.



b.
C369722

Install the front flexible hose and front speed sensor to the front shock absorber assembly with the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)

NOTICE:

Do not twist the front flexible hose when installing it.



Hide 12.INSTALL FRONT WHEEL

Hide 13.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

a.

Connect the reservoir level switch connector.


b.

Connect the cable to the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>AUXILIARY BATTERY>INSTALLATION


c.

Turn the power switch on (READY).


d.

Depress the brake pedal and release it.